User manual

Section 5: Module Configuration 5-5
Moseley SL9003Q 602-12016 Revision G2016 Revision G
MPEG Encoder-M
M1 M0 ISO/MPEG Coding mode
off=0 off=0 mono
off=0 on=1 dual channel /double mono (C5)
on=1 off=0 joint stereo [default]
on=1 on=1 stereo
M5 M4 M3 M2 Output Rate
off=0 off=0 off=0 off=0 reserved
off=0 off=0 off=0 on=1 32 kb/s
off=0 off=0 on=1 off=0 48 kb/s
off=0 off=0 on=1 on=1 56 kb/s
off=0 on=1 off=0 off=0 64 kb/s
off=0 on=1 off=0 on=1 80 kb/s
off=0 on=1 on=1 off=0 96 kb/s
off=0 on=1 on=1 on=1 112 kb/s
on=1 off=0 off=0 off=0 128 kb/s
on=1 off=0 off=0 on=1 160 kb/s
on=1 off=0 on=1 off=0 192 kb/s
on=1 off=0 on=1 on=1 224 kb/s
on=1 on=1 off=0 off=0 256 kb/s [default]
on=1 on=1 off=0 on=1 320 kb/s
on=1 on=1 on=1 off=0 384 kb/s
on=1 on=1 on=1 on=1 forbidden
Audio In Card
E2-E5 Analog Input Impedance
600 600 ohms
HI-Z >10kohms (default)
E3-E6
dB Gain Nominal Input Level
0 0 (default) +10 dBu (default)
6 6 +4 dBu
20 20 -10 dBu
40 40 -30 dBu
MPEG-Encoder A
A7 A6 ISO/MPEG Input Rate
off=0 off=0 44.1 kHz
off=0 on=1 48.0 kHz (default)
on=1 off=0 32 kHz
on=1 on=1 reserved
A5
A4 A3
0 0 0 reserved
A2
A1 A0
0 0 0 reserved
MPEG Encoder - C
C5 Coding Mode
off=0 dual channel [default]
on=1 double mono
S52 – System Clock
TXD TXC Modem TX Compressed
off X TXDATA disabled [default]
on X TXDATA enabled
X off TXCLK disabled [default]
X on TXCLK enabled
S52-3
S52-4 Modem TX Linear
off X TXDATA disabled [default]
on X TXDATA enabled
X off TXCLK disabled [default]
X on TXCLK enabled
S31 – System Config
M1 M2 Input Rate (A/D & AES/EBU/SPDIF &SRC
off=0 off=0 44.1 kHz (internal osc)
off=0 on=1 48.0 kHz (internal osc)
on=1 off=0 32.0 kHz (internal osc) [default]
on=1 on=1 AES/EBU (variable from AES/EBU/SPDIF)
M3 AES/EBU/SPDIF mode
off=0 AES=master A/D=secondary [default]
on=1 No input switching (M1, M2=source)
M4 M5 M6 VCO Clock Source Bus Clock
off=0 off=0 off=0 input mode (M1,M2) ignore
off=0 off=0 on=1 internal oscillator ignore
off=0 on=1 off=0 trunk compressed ignore
off=0 on=1 on=1 trunk linear ignore
on=1 off=0 off=0 reserved input
on=1 off=0 on=1 reserved input
on=1 on=1 off=0 mux compressed input
on=1 on=1 on=1 mux linear input
M7 M8 Linear Data Rate
off=0 off=0 44.1 kHz
off=0 on=1 48.0 kHz
on=1 off=0 32.0 kHz [default]
on=1 on=1 44.0 kHz
S23 – System Config
R1 R2 Sample Rate Converter Data Source
off=0 off=0 AES/EBU/SPDIF [default]
off=0 on=1 A/D Converter
on=1 off=0 Zeros (gnd)
on=1 on=1 Sine Generator
R3
Bus Master Clock
off=0 receive clock from mux bus [default]
on=1 supply clock to mux bus
R4 Aux RS-232 Data
off=0 Disabled
on=1 Enabled [default]
R5 R6 2- /4 – Channel Select
off=0 off=0 2-Channel
off=0 on=1 reserved
on=1 off=0 4-Channel Master (1st pair)
on=1 on=1 4-Channel Slave (2nd pair)
R7 9003 LEDs & Metering
off=0 Disabled /FP Select [default]
on=1 Enabled / Forced On
R8 Debug
off=0 Normal [default]
on=1 Debug (B-bus = outputs)
S22 – Board ID
A2 A3 A4 A5 A6 A7 A8 A9 Board # Base Addr
off off off off off off off off 0 0
off on off off off off off off 2 8
off off on off off off off off 3 16
off off off on off off off off 4 32
off off off off off on off off 6 128
off off off off off off on off 7 256
S21 – Data Channel
D1 D2 Aux Data # of Bits
off=0 off=0 6 (6N/5E/50)
off=0 on=1 7 (7N/6E/60)
on=1 off=0 8 (8N/7E/70) [default]
on=1 on=1 9 (9N/8E/80)
D3 D4 D5 Aux Date Rate
off=0 off=0 off=0 300
off=0 off=0 on=1 600
off=0 on=1 off=0 1200 [default]
off=0 on=1 on=1 2400
on=1 off=0 off=0 4800
on=1 off=0 on=1 9600 +
on=1 on=1 off=0 19200 +
on=1 on=1 on=1 38400 +
+ MUST use CTS Line
D6 Reserved
off=0 Reserved [default]
on-1 Reserved
D7 Test
off=0 Disabled [default]
on=1 Enabled
D8 Debug
off=0 Normal [default]
on=1 Enabled
M7 M6
0 0 reserved
S81 – AES/EBU
..
S81-A S81-B S81-C S81-D S81-E AES/EBU/SPDIF
off on off off on AES/EBU (default)
on on off off off SPDIF
S81-VERF S81-ERF AES/EBU VERF/ERF
on off Validity Bit & Error Flag
off on Error Flag Only (default)
S81-8 Reserved
off=0 reserved
Figure 5-3 Audio Encoder PC Board / Switch & Jumper Settings