User manual
Table Of Contents
- User Manual
- Starlink SL9003Q
- Digital Studio Transmitter Link
- WARRANTY
- SL9003Q Manual Dwg # 602-12016-01 R: G Revision Levels:
- Using This Manual - Overview
- Section 1 System Features and Specifications
- Section 2 Quick Start
- Section 3 Installation
- Section 4 Operation
- Section 5 Module Configuration
- Section 6 Customer Service
- Section 7 System Information
- Table of Contents
- List of Figures
- List of Tables
- 1 System Features and Specifications
- 2 Quick Start
- 3 Installation
- 4 Operation
- 7.1 Introduction
- 7.2 Front Panel Operation
- 4.3 Screen Menu Navigation and Structure
- 7.4 Screen Menu Summaries
- 4.4.1 Meter
- 4.4.2 System: Card View
- 4.4.3 System: Power Supply
- 4.4.4 System: Info
- 4.4.5 System: Basic Card Setup
- 4.4.6 Factory Calibration
- 4.4.7 SYSTEM: UNIT-WIDE PARAMS
- 4.4.8 System: Date/Time
- 4.4.9 System: Transfer
- 4.4.10 System: External I/O (NMS)
- 4.4.11 Alarms/Faults
- 4.4.12 Radio: Modem Status (QAM)
- 4.4.13 Radio TX Status
- 4.4.14 Radio RX Status
- 4.4.15 Radio TX Control
- 4.4.16 Radio RX Control
- 4.4.17 Radio Modem (QAM) Configure
- 4.4.18 Radio TX Configure
- 4.4.19 Radio RX Configure
- 4.4.20 Radio Modem/TX/RX Copy Function
- 4.5 Intelligent Multiplexer PC Interface Software
- 4.6 NMS/CPU PC Interface Software
- 5 Module Configuration
- 6 Customer Service
- 7 System Description
- 8 Appendices
- Appendix A: Path Evaluation Information
- Appendix B: Audio Considerations
- Appendix C: Glossary of Terms
- Appendix D: Microvolt – dBm – Watt Conversion (50 ohms)
- Appendix E: Spectral Emission Masks
- Appendix F: Redundant Backup with TP64 and TPT-2 Transfer Panels
- Appendix G: Optimizing Radio Performance For Hostile Environments
- Appendix H: FCC APPLICATIONS INFORMATION - FCC Form 601
- Starlink SL9003Q & Digital Composite - 950 MHz Band
Section 5: Module Configuration 5-3
Moseley SL9003Q 602-12016 Revision G
Digital Data Stream I/O:
(V.35/RS449)
Data Output: RS232 levels,
9pin D male, Asynchronous
300-38400 bps (4800 max
for ADPCM)
AES/EBU/SPDIF
Zout=110 ohm, transformer
balanced, 32, 44.1, 48 kHz
sample rate (32 kHz typ.)
Left (Ch.1)/Right (Ch.2):
Zout<50 ohm, active
balanced, +10dBu = 0 VU
AUDIO DEC
SPDIF
AES/EBU
TRUNK
DATA
CH. 1
LEFT
CH. 2
RIGHT
CMPR
LIN
ID#
Figure 5-2 Audio Decoder Front Panel
Switch and jumper settings for the Audio Encoder and Audio Decoder are shown in
Figures 5-1 and 5-2, respectively. The following sections will clarify the particular
groupings of switches.
CAUTION:
Avoid excessive pressure on the audio adjustment potentiometers located
on the back panels of the Audio Encoder/Decoder modules.