User manual
Table Of Contents
- User Manual
- Starlink SL9003Q
- Digital Studio Transmitter Link
- WARRANTY
- SL9003Q Manual Dwg # 602-12016-01 R: G Revision Levels:
- Using This Manual - Overview
- Section 1 System Features and Specifications
- Section 2 Quick Start
- Section 3 Installation
- Section 4 Operation
- Section 5 Module Configuration
- Section 6 Customer Service
- Section 7 System Information
- Table of Contents
- List of Figures
- List of Tables
- 1 System Features and Specifications
- 2 Quick Start
- 3 Installation
- 4 Operation
- 7.1 Introduction
- 7.2 Front Panel Operation
- 4.3 Screen Menu Navigation and Structure
- 7.4 Screen Menu Summaries
- 4.4.1 Meter
- 4.4.2 System: Card View
- 4.4.3 System: Power Supply
- 4.4.4 System: Info
- 4.4.5 System: Basic Card Setup
- 4.4.6 Factory Calibration
- 4.4.7 SYSTEM: UNIT-WIDE PARAMS
- 4.4.8 System: Date/Time
- 4.4.9 System: Transfer
- 4.4.10 System: External I/O (NMS)
- 4.4.11 Alarms/Faults
- 4.4.12 Radio: Modem Status (QAM)
- 4.4.13 Radio TX Status
- 4.4.14 Radio RX Status
- 4.4.15 Radio TX Control
- 4.4.16 Radio RX Control
- 4.4.17 Radio Modem (QAM) Configure
- 4.4.18 Radio TX Configure
- 4.4.19 Radio RX Configure
- 4.4.20 Radio Modem/TX/RX Copy Function
- 4.5 Intelligent Multiplexer PC Interface Software
- 4.6 NMS/CPU PC Interface Software
- 5 Module Configuration
- 6 Customer Service
- 7 System Description
- 8 Appendices
- Appendix A: Path Evaluation Information
- Appendix B: Audio Considerations
- Appendix C: Glossary of Terms
- Appendix D: Microvolt – dBm – Watt Conversion (50 ohms)
- Appendix E: Spectral Emission Masks
- Appendix F: Redundant Backup with TP64 and TPT-2 Transfer Panels
- Appendix G: Optimizing Radio Performance For Hostile Environments
- Appendix H: FCC APPLICATIONS INFORMATION - FCC Form 601
- Starlink SL9003Q & Digital Composite - 950 MHz Band
Section 4: Operation 4-13
Moseley SL9003Q 602-12016 Revision G
4.4.6 Factory Calibration
The Factory Calibration Screens are documented below. The user may refer to this
diagram when instructed to do so by Moseley customer service technicians.
Though the user is given access to the factory calibration menu area to allow for field
servicing and monitoring of certain measurements, be aware that changing any
parameter (pressing ENTER) may cause the units to fail to operate properly.
Caution
Changing Factory Calibration may cause the link to fail. Do not change
unless directed by Moseley Customer Services personnel
RADIO TX
Factory Calibrate
RADIO RX
QAM MODEM
SYSTEM
RADIO TX-A Cal
FWD PWR
REV PWR
ALC
PA CUR
RADIO TX-A Cal
AFC LVL
LO LVL
XCTR LVL
FWD Pwr-A Calibr.
Pwr Adjust 112 111
Calibr Val
Reading 1.00
0.96
REV Pwr-A Calibr.
Calibr Val
Reading 0.25
0.03
ALC-A Calibr
PA LC AUTO
PA Current-A Calibr
Calibr Val
Reading 2.40
1.91
AFC Lvl-A Calibr
Calibr Val
Reading 4.50
2.36
LO Lvl-A Calibr
Calibr Val
Reading 100.00
97.09
XCTR Lvl-A Calibr
Calibr Val
Reading 100.00
100.00
Figure 4-5 Factory Calibration-Radio TX Screens