Installation Sheet

ManualsBrandsBrizo ManualsBrizo CollectionsBrizo Levoir Widespread Bidet Faucet with Pop-Up Drain Assembly and Diverter with Integral Vacuum Breaker - Less Handles

TWO HANDLE WIDESPREAD BIDET FAUCET

WITH INTEGRAL VACUUM BREAKER - LESS HANDLES

LLAVE DE AGUA DE PIEZAS SEPARADAS, DE DOS MANIJAS,

PARA BIDETS CON EL TRITURADOR INTEGRAL DEL VACÍO –

SIN MANIJAS

ROBINET À GRAND ENTRAXE ET À DEUX MANETTES POUR

BIDET AVEC LE BRISEUR INTÉGRAL DE VIDE - SANS LES

MANETTES

Levoir™

Model/Modelo/Modèle

68498-sLHP

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

SILICONE

Icons

Para instalación fácil de su llave

Brizo

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Comprar las conexiones correctas para el

suministro de agua.

For easy installation of your

Brizo

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To purchase the correct water supply hook-up.

Pour installer votre robinet

Brizo

facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

• Acheter le bon nécessaire de raccordement.

07/02/2018 Rev. B

SILICONE

Icons

SILICONE

Icons

sSpecify Finish / Especifíque el Acabado / Précisez le Fini

www.brizo.com

92794

Note: Handle kits must be

ordered separately.

Nota: los juegos de manijas se

venden por separado.

Note : Manettes en kit vendues

séparément.

3/32" (2.38mm)

3/32 po (2.38mm)

3 mm

3/32"

Summary of content (8 pages)

PAGE 1
92794 TWO HANDLE WIDESPREAD BIDET FAUCET WITH INTEGRAL VACUUM BREAKER - LESS HANDLES LLAVE DE AGUA DE PIEZAS SEPARADAS, DE DOS MANIJAS, PARA BIDETS CON EL TRITURADOR INTEGRAL DEL VACÍO – SIN MANIJAS Levoir™ Model/Modelo/Modèle 68498-sLHP ROBINET À GRAND ENTRAXE ET À DEUX MANETTES POUR BIDET AVEC LE BRISEUR INTÉGRAL DE VIDE - SANS LES MANETTES Note: Handle kits must be ordered separately. Nota: los juegos de manijas se venden por separado. Write purchased model number here.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
2 1 2 3 mm 3 4 1 OPERATING INSTRUCTIONS MAINTENANCE A. Check to be sure diverter valve handle (1) is in the rim feed position (turned fully clockwise). B. Turn on hot and cold water valves and adjust for desired temperature. C. To divert to rosette spray, slowly turn diverter handle fully counterclockwise. Note: It is normal for a little water to come out of rim feed hole when system is in rosette spray position and vice versa. D. To fill bowl, pull up on lift rod knob (2).
PAGE 4
Levoir™ Model/Modelo/Modèle 68498-sLHP RP92362 Spline Adapter and Screw Adaptador con estrías y tornillo Adaptateur cannelé et vis RP62796▲ Diverter Handle & Set Screw Manija Desviadora y Tornillo de Ajuste Manette d’inverseur et vis de calage RP62797▲ Diverter Body Cuerpo Desviador Corps d’inverseur RP46408 Mounting Flange w/Gasket Brida de Montaje con Empaque Collerette avec joint RP61825 Valve Cartridge, Hot Side Cartucho de la Válvula, Lado Caliente Cartouche de soupape, eau chaude RP100422p Handle
PAGE 5
1 A. B. 3 3 2 2 1 1 4 2 C. 3 3/32" 2 D. 2 3 1 4 1 5 6 1 2 INSTALLATION OF DIVERTER VALVE/VACUUM BREAKER Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. Hole size must be 1-1/8” diameter minimum. A. B. C. D. Connect diverter valve (1) with “Y” and gasket (2) as shown in illustration. Slide one rubber cone washer (3), with smaller tapered end pointing up, onto diverter valve all the way to the base.
PAGE 6
3 B. A. 4 3 5 2 4 1 C. D. 10 8 9 6 7 6 5 INSTALLATION OF VALVE ASSEMBLIES & TRIM Note: Holes for valves must be 1-1/8" diameter minimum and must be at least 5" apart. Look for a blue label or dot on cold valve assembly and red label or dot on hot valve assembly and install them on appropriate side. A. Install mounting nut (1) onto end valve shank (2). Position gasket (3) into the groove of adapter nut (4). Place the end valve shank through mounting hole from the bottom.
PAGE 7
4 A. C. B. E. D. 1 1 2 3 2 3 2 1 1 1 G. F. 4 2 2 H. 5 5 3 1 2 1 5 1 6 3 2 4 2 POP-UP INSTALLATION A. Remove stopper (1) and flange (2). D. Apply silicone to underside of flange (1). Insert G. Remove pivot nut (1). Install horizontal rod B. Screw nut (1) all the way down. Push washer (2) E. Pivot (1) must face faucet. Pull assembly (2) down H. Install rod guide assembly (1). Attach and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece.
PAGE 8
5 6 1 2 A. 3 1 3 1/2" (12.7 mm) IPS 2 3 2 B. MAKE CONNECTIONS TO WATER LINES: FLUSH YOUR SYSTEM Choose hook-ups for 1/2" I.P.S. connections: (1) Ball nose riser (3/8" O.D. copper tubing), or (2) 1/2" I.P.S. faucet connector. A. Turn diverter handle (1) clockwise to ‘rim feed’ position. Turn on water supplies (2) and turn hot and cold handles (3) to open position for one minute to flush any debris from system. Use coupling nuts (3) with the ball nose risers (1).