Installation Sheet

ManualsBrandsBrizo ManualsBathroom FaucetsBidet Faucet Double Handle Less Handles from the RSVP Collection

TWO HANDLE WIDESPREAD BIDET FAUCETS

WITH INTEGRAL VACUUM BREAKER - LESS HANDLES

LLAVES DE AGUA DE PIEZAS SEPARADAS, DE

DOS MANIJAS, PARA BIDETS CON EL TRITURADOR

INTEGRAL DEL VACÍO - SIN MANIJAS

ROBINETS À GRAND ENTRAXE ET À DEUX MANETTES

POUR BIDET AVEC LE BRISEUR INTÉGRAL DE VIDE -

SANS LES MANETTES

Model/Modelo/Modèle

68490-sLHP

Series/Series/Seria

RSVP

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

SILICONE

Icons

Para instalación fácil de su llave

Brizo

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Comprar las conexiones correctas para el

suministro de agua.

For easy installation of your

Brizo

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To purchase the correct water supply hook-up.

Pour installer votre robinet

Brizo

facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

• Acheter le bon nécessaire de raccordement.

8/25/15 Rev. D

SILICONE

Icons

Note: Handle kits must be

ordered separately.

Nota: los juegos de manijas se

venden por separado.

Note : Manettes en kit vendues

séparément.

www.brizo.com

54535

SILICONE

Icons

sSpecify Finish / Especifíque el Acabado / Précisez le Fini

Summary of content (8 pages)

PAGE 1
54535 TWO HANDLE WIDESPREAD BIDET FAUCETS WITH INTEGRAL VACUUM BREAKER - LESS HANDLES LLAVES DE AGUA DE PIEZAS SEPARADAS, DE DOS MANIJAS, PARA BIDETS CON EL TRITURADOR INTEGRAL DEL VACÍO - SIN MANIJAS Model/Modelo/Modèle 68490-sLHP Series/Series/Seria RSVP® ROBINETS À GRAND ENTRAXE ET À DEUX MANETTES POUR BIDET AVEC LE BRISEUR INTÉGRAL DE VIDE - SANS LES MANETTES Note: Handle kits must be ordered separately. Nota: los juegos de manijas se venden por separado. Write purchased model number here.
PAGE 2
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
2 1 2 3 mm 3 4 1 OPERATING INSTRUCTIONS MAINTENANCE A. Check to be sure diverter valve handle (1) is in the rim feed position (turned fully clockwise). B. Turn on hot and cold water valves and adjust for desired temperature. C. To divert to rosette spray, slowly turn diverter handle fully counterclockwise. Note: It is normal for a little water to come out of rim feed hole when system is in rosette spray position and vice versa. D. To fill bowl, pull up on lift rod knob (2).
PAGE 4
RP26853 Allen Wrench Llave Allen Clé Allen HL5390▲ Lever Handle & Body, Hot Side Palanca y Cuerpo, Lado Caliente Manette et corps, eau chaude RP63514▲ Diverter Handle & Set Screw Manija Desviadora y Tornillo de Ajuste Manette d’inverseur et vis de calage RP46408 Mounting Flange w/Gasket Brida de Montaje con Empaque Collerette avec joint RP46409 Screw & Stem Tornillo y Espiga Vis et tige RP61825 Valve Cartridge, Hot Side Cartucho de la Válvula , Lado Caliente Cartouche de soupape, eau chaude RP44193 Gaske
PAGE 5
1 A. B. 3 3 2 2 1 1 4 2 C. 3 2 mm 2 D. 2 3 1 4 5 1 6 1 2 INSTALLATION OF DIVERTER VALVE/VACUUM BREAKER Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. Hole size must be 1-1/8” diameter minimum. A. B. C. D. Connect diverter valve (1) with “Y” and gasket (2) as shown in illustration. Slide one rubber cone washer (3), with smaller tapered end pointing up, onto diverter valve all the way to the base.
PAGE 6
3 B. A. 5 1 4 3 2 1 C. D. 2 1 1 2 1 INSTALLATION OF VALVE ASSEMBLIES & TRIM Note: Holes for valves must be 1-1/8" diameter minimum and must be at least 5" apart. Look for a blue label or dot on cold valve assembly and red label or dot on hot valve assembly and install them on appropriate side. mounting parts to side valve (1); nut (2), washer (3), & gasket (4), making A. Assemble sure to screw nut down to near bottom of threads.
PAGE 7
C. B. E. D. NE I CO 1 SIL 4 A. 1 2 3 2 3 2 1 1 1 G. F. 4 2 2 H. 5 5 3 1 2 1 5 1 6 3 2 4 2 Step 3b POP-UP INSTALLATION A. Remove stopper (1) and flange (2). D. Apply silicone to underside of flange (1). Insert B. Screw nut (1) all the way down. Push washer (2) E. Pivot (1) must face faucet. Pull assembly (2) down and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. body (2) into sink. Screw flange (1) into body (2).
PAGE 8
5 6 A. 3 1 3 1/2" (12.7 mm) IPS 2 2 3 B. 1 2 MAKE CONNECTIONS TO WATER LINES: FLUSH YOUR SYSTEM Choose hook-ups for 1/2" I.P.S. connections: (1) Ball nose riser (3/8" O.D. copper tubing), or (2) 1/2" I.P.S. faucet connector. A. Turn diverter handle (1) clockwise to ‘rim feed’ position. Turn on water supplies (2) and turn hot and cold handles (3) to open position for one minute to flush any debris from system. Use the enclosed coupling nuts (3) with the ball nose risers (1).