Installation Sheet

ManualsBrandsBrizo ManualsBrizo CollectionsBrizo Rook 18 GPM Widespread Bidet Faucet with Pop-Up Drain Assembly

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

Para instalación fácil de su llave

Brizo

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Comprar las conexiones correctas para el

suministro de agua.

For easy installation of your Brizo

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To purchase the correct water supply hook-up.

Pour installer votre robinet Brizo

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

• Acheter le bon nécessaire de raccordement.

Models/Modelos/Modèles

68460-LHP▲

Series/Serias/Seria

Rook™

4/21/15 Rev. A

TWO HANDLE ROSETTE BIDET VALVE & DIVERTER

WITH VACUUM BREAKER AND POP-UP ASSEMBLY

- LESS HANDLES

VÁLVULA DE DOS MANIJAS PARA BIDÉS CON

BOQUILLA DE ROCÍO Y DESVIADOR CON ROMPE-

VACÍO Y DESAGÜE AUTOMÁTICO – SIN MANIJAS

ROBINET À DEUX MANETTES POUR BIDET AVEC

GICLEUR, INVERSEUR À BRISE-VIDE ET RENVOI

MÉCANIQUE - SANS LES MANETTES

3/32" (2.38mm)

3/32 po (2.38mm)

2 mm

www.brizo.com

▲Specify Finish / Especifíque el Acabado / Précisez le Fini

80439

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

80439

Note: Handle kits must be

ordered separately.

Nota: los juegos de manijas se

venden por separado.

Note : Manettes en kit vendues

séparément.

Summary of content (8 pages)

PAGE 1
80439 Models/Modelos/Modèles 68460-LHP▲ Series/Serias/Seria Rook™ TWO HANDLE ROSETTE BIDET VALVE & DIVERTER WITH VACUUM BREAKER AND POP-UP ASSEMBLY - LESS HANDLES VÁLVULA DE DOS MANIJAS PARA BIDÉS CON BOQUILLA DE ROCÍO Y DESVIADOR CON ROMPEVACÍO Y DESAGÜE AUTOMÁTICO – SIN MANIJAS ROBINET À DEUX MANETTES POUR BIDET AVEC GICLEUR, INVERSEUR À BRISE-VIDE ET RENVOI MÉCANIQUE - SANS LES MANETTES Note: Handle kits must be ordered separately. Nota: los juegos de manijas se venden por separado.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
RP28653▲ Metal Pop-Up Assembly Less Lift Rod Ensamble de Metal del Desagüe Automático Menos la Barra de Alzar Renvoi mécanique en métal sans la tige de manoeuvre Handles (sold separately) Manijas (se vende por separado) Manettes (vendu séparément) RP78584▲ Buttons & Friction Rings Botóns y Argolla de la Fricción Boutons et boucle de frottement RP63514▲ Diverter Handle & Set Screw Manija Desviadora y Tornillo de Ajuste Manette d’inverseur et vis de calage HL5360▲ (Lever) Handles & Glide Rings Manijas y a
PAGE 4
2 6 7 3 4 5 1 MAINTENANCE OPERATING INSTRUCTIONS SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE ASSEMBLIES. If your bidet faucet leaks out of rim feed area, or from rosette sprayer, or around handle body area, replace valve cartridge (1). A. Check to be sure diverter valve handle (6) is in the rim feed position (turned fully clockwise). B. Turn on hot and cold water valves and adjust for desired temperature. C. To divert to rosette spray, slowly turn diverter handle fully counterclockwise.
PAGE 5
1 A. C. 3 2 3 2 1 1 4 2 B. 2 7 D. 3 6 1 4 5 5 6 1 2 INSTALLATION OF DIVERTER VALVE/VACUUM BREAKER Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. Hole size must be 1-1/8" diameter minimum. A. Assemble diverter valve (1) with “Y” and gasket (2) as shown in illustration. Slide one rubber cone washer (3), with smaller tapered end pointing up, onto diverter valve all the way to the base.
PAGE 6
3 A. C. 4 3 8 6 2 7 1 B. D. 11 11 10 9 5 6 4 INSTALLATION OF VALVE ASSEMBLIES & TRIM Note: Holes for valves must be 1-1/8" diameter minimum and must be at least 5" apart. Look for a blue label or dot on cold valve assembly and red label or dot on hot valve assembly and install them on appropriate side. A. Install mounting nut (1) onto end valve shank (2). Position gasket (3) into the groove of adapter nut (4). Place the end valve shank through mounting hole from the bottom.
PAGE 7
C. B. E. D. NE I CO 9 2 SIL 4 A. 1 2 5 7 8 4 10 3 6 G. F. 12 7 7 H. 13 1 14 11 10 17 4 18 15 11 16 11 Step 3b METAL POP-UP Step 3c A. Remove stopper (1) and flange (2). D. Apply silicone to underside of flange (9). Insert body G. Remove pivot nut (10). Install horizontal rod B. Screw nut (3) all the way down. Push washer (4) and gasket (5) down. E. Pivot (10) must face faucet. Pull body (7) down firmly H. Install rod guide assembly (14). Attach C.
PAGE 8
6 5 A. 1 3 3 3 1 2 3 2 1 1 2 4 B. 5 4 5 FLUSH YOUR SYSTEM A. Turn diverter handle (1) clockwise to ‘rim feed’ position. Turn on water Connect 12" hoses (1) from “Y” on diverter valve (2) to outlets on hot & cold end valve bodies (3) as shown. Tighten firmly but do not over tighten. Connect inlet hoses (4) to hot and cold valve inlets (5) as shown. Tighten firmly but do not over tighten.