Installation Guide

ManualsBrandsBrizo ManualsBathroom FaucetsTresa Wall Mounted Bathroom Faucet - Limited Lifetime Warranty

TWO HANDLE WALL MOUNTED LAVATORY FAUCETS

LLAVES DE AGUA DE DOS MANIJAS DE LAVAMANOS

PARA INSTALACIÓN EN LA PARED

ROBINETS À DEUX MANETTES POUR LAVABO,

MONTAGE AU MUR

Model/Modelo/Modèle

65836LF

Series/Series/Seria

Tresa

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

ASME A112.18.1 / CSA B125.1

ASME A112.18.2 / CSA B125.2

ICC/ANSI A117.1

SILICONE

Para instalación fácil de su llave

Brizo

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Comprar las conexiones correctas para el

suministro de agua.

For easy installation of your

Brizo

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To purchase the correct water supply hook-up.

Pour installer votre robinet

Brizo

facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

• Acheter

le bon nécessaire de raccordement.

04/01/2013 Rev.Ewww.brizo.com

3 mm

61564

Summary of content (8 pages)

PAGE 1
61564 TWO HANDLE WALL MOUNTED LAVATORY FAUCETS LLAVES DE AGUA DE DOS MANIJAS DE LAVAMANOS PARA INSTALACIÓN EN LA PARED ROBINETS À DEUX MANETTES POUR LAVABO, MONTAGE AU MUR ASME A112.18.1 / CSA B125.1 ASME A112.18.2 / CSA B125.2 ICC/ANSI A117.1 Model/Modelo/Modèle 65836LF Series/Series/Seria Tresa® Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
RP62515 O-Rings Anillos “O” Joints Toriques RP61577▲ Escutcheon, O-ring and Gasket Escudete/chapa, Anillo O y Empaque Rosace, joint torique et joint RP40119 Set Screw & Allen Wrench 3 mm Tornillo de Ajuste y Llave Allen, 3 mm Vis et Clé Allen, 3 mm RP63031▲ Aerator Aireador Aérateur RP75782▲ Handle sleeve base , Stem & Valve Cartridge, Cold Side Base y espiga de la manga para la manija y Cartucho de la Válvula, Lado Frío Embase de manette gainée et tige et Cartouche de soupape, eau froide RP61575 Stem E
PAGE 4
1 1 2 3 8 5 3 7 3.2 mm 6 2 4 MAINTENANCE – VALVES SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES MAINTENANCE – SPOUT If your faucet leaks out of spout or around handle body, replace valve cartridge (1). A. Remove handle blade (2) from body (3) by turning blade counterclockwise. B. Using an allen wrench, loosen set screw (4) inside handle body (3). Pull body from adapter (5). C. Remove adapter (5) and stem extender (6). Unthread handle base (7). D.
PAGE 5
1 A. 2 Min. 11 1/2" Min. 11 1/2 po 2 1/8" - 3 1/2" 2 1/8 po - 3 1/2 po Min. 3" Min. 3 po 1 B. 1 1 1 FAUCET INSTALLATION NOTE: It is very important that the spout tip of this faucet be at least 1" minimum above the rim of the bowl after installation. Lay out your installation carefully to assure this air gap. A. Construct a suitable stud brace for mounting of the valve body. Refer to the roughing-in dimensions located on the plaster guard sleeves on valve body. NOTE: Indicated min. / max.
PAGE 6
3 4 4" (100 mm) 1 1/2" (38 mm) Diameter 5 1 3 4 2 MOUNTING WALL ESCUTCHEONS Note: One of the escutcheons has a Brizo logo (1) on it. It is suggested that this escutcheon be placed over the center spout sleeve with the logo at the bottom 6 o’clock position. Pull off plasterguards (2) and discard them. Assemble gaskets (3) and escutcheons (4). Carefully slide the escutcheons and gaskets over each sleeve of the valve body (5).
PAGE 7
6 5 2 3 6 1 4 3 mm 5 1 7 2 HANDLE INSTALLATION Install set screw (1) (the longer set screw) into end of handle blade (2). Thread handle stem adapter (3) into stem extender (4). Ensure glide ring (5) is installed inside the handle base (6); then, slide handle base onto the stem adapter. Make sure handle base is properly seated on stem adapter and secure with set screw (7). Hand tighten handle blade in handle base. Repeat this step for the other handle.
PAGE 8
7 1 2 2 FLUSH YOUR SYSTEM Remove aerator (1) and turn both faucet handles (2) to full open position. Turn on hot and cold supplies (if not already open) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts or disrupt water flow from your faucet. After flushing, turn handles to off position and reinstall aerator. HAGA FLUIR EL AGUA POR SU SISTEMA Quite el aireador (1) and gire ambas manijas (2) a la posición completamente abierta.