Installation Guide

ManualsBrandsBrizo ManualsKitchen FaucetsSolna Pull-Out Kitchen Faucet - Limited Lifetime Warranty

HIGH-RISE PULL-DOWN KITCHEN,

PULL-OUT AND BAR / PREP FAUCETS

LLAVES DE AGUA-GRIFOS CUELLO

DE GANSO, DESPLEGABLES PARA LA

COCINA, EXTRAÍBLES Y PARA BAR / PREP

ROBINETS COL-DE-CYGNE À BEC-

DOUCHETTE RÉTRACTABLE POUR ÉVIER

DE CUSINE, ROBINETS À BEC-DOUCHETTE

RÉTRACTABLE ET ROBINETS POUR ÉVIER

DE BAR OU D’ÎLOT

Models/Modelos/Modèles

63020LF, 63220LF & 63920LF

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

SILICONE

1/18/13 Rev. A

ASME A112.18.1 / CSA B125.1

ICC/ANSI A117.1

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

SOLNA

75133

Para instalación fácil de su llave

Brizo

usted necesitará:

•LEER TODAS las instrucciones completamente

antes de empezar.

•LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your

Brizo

faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•To READ ALL warnings, care, and

maintenance information.

Pour installer votre robinet

Brizo

facilement, vous devez:

•LIRE TOUTES les instructions avant de débuter;

•LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

www.brizo.com

63020LF

63220LF 63920LF

Summary of content (12 pages)

PAGE 1
HIGH-RISE PULL-DOWN KITCHEN, PULL-OUT AND BAR / PREP FAUCETS LLAVES DE AGUA-GRIFOS CUELLO DE GANSO, DESPLEGABLES PARA LA COCINA, EXTRAÍBLES Y PARA BAR / PREP ROBINETS COL-DE-CYGNE À BECDOUCHETTE RÉTRACTABLE POUR ÉVIER DE CUSINE, ROBINETS À BEC-DOUCHETTE RÉTRACTABLE ET ROBINETS POUR ÉVIER DE BAR OU D’ÎLOT 75133 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 Models/Modelos/Modèles 63020LF, 63220LF & 63920LF Series/Series/Seria SOLNA® Write purchased model number here.
PAGE 2
Limited Warranty on Brizo® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Brizo® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
The Solna 63020LF pull-down and 63920LF prep models have been produced in two configurations. If you have a problem with your faucet and need to contact Delta Faucet, please take a few moments to determine which design option you have installed. Los modelos 63020LF Solna desplegable y 63920LF para preparativos han sido fabricados en dos configuraciones.
PAGE 4
Current Configuration See page 3 to identify the correct configuration. Configuración actual Vea la página 3 para identificar la configuración correcta. Configuration actuelle Consultez la page 3 pour déterminer la bonne configuration.
PAGE 5
Configuración original Original Configuration Vea la página 3 para identificar la configuración correcta. See page 3 to identify the correct configuration. Configuration initiale Consultez la page 3 pour déterminer la bonne configuration.
PAGE 6
Backflow Protection System Other useful accessories that may be purchased separately. Otros accesorios útiles que se pueden comprar por separado. Autres accessoires utiles pouvant être achetés séparément. Your Brizo® faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1.
PAGE 7
1 B. A. 3 2 2 2 1 1 2 2 Mount Faucet to Deck A. Your faucet is designed for a hole diameter of 1 3/8" +/- 1/4" (35 mm +/- 6 mm) and a deck thickness of up to 3" (76 mm). Install gasket (1) into groove under faucet base (2). Insert faucet tubes and shank through mounting hole in sink; and, place faucet over mounting hole. Note: With 10 1/2" escutcheon, maximum deck thickness is reduced to 2 3/4" (69.8 mm). Instale la Llave de Agua en el Borde A.
PAGE 8
OPTIONAL / OPCIONAL / FACULTATIVE 2 1 4 2 1 5 3 3 4 2 2 3 4 2 4 5 5 5 4 6 2 6 Incorrect Installations. Optional Escutcheon Installation Hose Installation For optional installations using the 10 1/2" escutcheon, order RP71451 (specify finish) not supplied. Place the 10 1/2" escutcheon (1) and gasket (2) under faucet base. Mount as shown above using the 2 1/4-20 studs (3), nuts and washers (4), mounting nut and washer (5). Tighten mounting nut (5) securely by hand.
PAGE 9
3 A. B. 2 OR 2 1 O 2 OU 3 1 4 3 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 10
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 11
4 B. A. C. 3 1 3 6 3 4 2 5 2 4 OR 6 5 5 1 A. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the spout. Be sure to hold the end of the hose down into the sink and turn faucet handle (3) to the mixed position. Note: To turn faucet on, move handle (3) away from body (4). Flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. Install the sprayer (5) and discard blue clip (6).
PAGE 12
3 6 2 5 4 3 1 2 Maintenance If faucet leaks from under handle or from spout outlet – Insert a small screwdriver into slot (1) in button (2) and remove. Loosen set screw (3) inside of handle. Remove handle. Remove bonnet (4) by rotating counterclockwise. Bonnet may be stiff due to O-ring, but should rotate by hand. Remove bonnet nut (5) by rotating counterclockwise with a wrench. Remove cartridge (6) by pulling directly back on stem. Replace cartridge and reassemble.