User Guide BT Digital Baby Monitor 300 2250 Baby Monitor 300 UG Iss2.[2].
Welcome… to your BT Digital Baby Monitor 300 • Digital sound quality with high definition sound (Hi-ds™) lets you hear your baby breathe, gurgle, snuffle or cry with complete clarity • Wireless range of up to 300m outdoors and up to 50m indoors (in ideal conditions, where there is a clear line of sight between the units) – giving you the freedom to move around with clear reception and no interference from other baby monitors • Out of range and battery low warnings • Link light provides continuous confidenc
This User Guide provides you with all the information you need to get the most from your BT Digital Baby Monitor 300. Please read this guide carefully and keep it for future reference.
Important safety information • Your BT Digital Baby Monitor 300 is designed to be an aid and should not be used as a substitute for responsible and proper adult supervision. • Make sure the Baby unit, Parent unit and mains adapter cables are kept out of reach of your baby – at least one metre away. • Never place the Baby unit inside your baby’s cot, bed or playpen. • Never cover your Parent or Baby units (e.g. with clothes, towels or blankets).
In this guide 5 Important safety information.............4 Adjust the nightlight brightness.........15 Your BT Digital Baby Monitor 300.......6 Talk back..........................................15 Parent unit.........................................6 Parent unit battery LED indicator.......16 Baby unit...........................................7 Find.................................................16 Back of the Baby unit..........................8 List of tones..................................
Your BT Digital Baby Monitor 300 Parent unit Lanyard attach point You can loop a lanyard (not supplied) through here. + Vol. Increase speaker volume. Talk Press to talk to your baby. - Vol. Decrease speaker volume. Mute is switched on when -Vol is pressed to the lowest level. Microphone Mute LED Steady red indicates that Mute has been switched on. Battery LED status indicator (top of unit) Red flashing light indicates the batteries are low and need re-charging.
Your BT Digital Baby Monitor 300 7 Baby unit Nightlight Press or to switch the nightlight on or off. for Press and hold 2 seconds to switch off. Find Press to emit an alert beep from the Parent unit – useful for finding the Parent unit if you’ve misplaced it. Link indicator Steady green indicates that the Baby and Parent units are linked. Flashes green if not linked for the first 30 seconds. Flashes red if not linked for longer than 30 seconds.
Your BT Digital Baby Monitor 300 Back of the Baby unit Power socket For connection to the mains power socket via the power adapter cable supplied. If you experience any problems, please call the Helpline on Freephone 0800 145 6789* or visit bt.com/producthelp 2250 Baby Monitor 300 UG Iss2.[2].
Setting up Parent unit 1. Plug one of the power adapter cables into the socket marked on the side of the Parent unit and plug the other end into the mains power wall socket and switch the power on. 2. Activate the batteries by pulling the plastic tab away from the top of the Parent unit and leave to charge for 24 hours to reach maximum charge. 24 9 WARNING! Only use the power adapters supplied. Using incorrect power adapters may permanently damage your product.
Setting up Battery low warning – Parent unit When the batteries are low – approximately within 1 hour of running out – the Parent unit will emit a low battery alert and the low battery indicator on the unit will flash red. Baby unit 1. Plug the remaining power adapter cable into the socket marked on the back of the Baby unit and plug the other end into the mains power and switch on. To speed up the charging process turn the Parent unit off when charging if it’s not being used.
Setting up Important: The link confirmation between the two units is vital for use so they can communicate. If the link between the units is broken at any time, the Link indicators on the Parent and Baby units will flash green as they try to search for each other. After 30 seconds, if the link is still broken they will flash red and you will also hear an alert signal from the Parent unit.
Using your BT Digital Baby Monitor 300 Switching on/off Switch the Baby unit on 1. Press and hold the button for 1 second. The nightlight will briefly illuminate and then the green LED will flash until it links with the Parent unit. Once linked the green LED will remain on. Switch the Parent unit on button on the Parent unit 1. Press and hold the until all the LEDs on the top of the unit briefly illuminate. The green Link indicator will flash.
Using your BT Digital Baby Monitor 300 13 Baby sound level LED indicators LEDs 1-4 = Green LEDs 5-7 = Red The seven LEDs across the top of the Parent unit light up to indicate the level of sound being received from the Baby unit. The LEDs light up progressively as the sound increases. LEDs 1-2 light up Green when sounds of 57dB and 63dB are received. LEDs 3-4 light up Green when sounds of 69dB and 75dB are received. LEDs 5-7 light up Red when sounds of 83dB, 89dB or 95dB are received.
Using your BT Digital Baby Monitor 300 If you try and set the volume higher or lower than the 5 settings available on either unit you will hear a double alert tone. or buttons are If the pressed while Mute has been set then Mute will be switched off and the loudspeaker volume will return to Level 3 automatically Adjust the Parent unit loudspeaker volume There are 5 volume levels and off (Mute). The default loudspeaker volume is Level 3. or to select the required level. You will 1.
Using your BT Digital Baby Monitor 300 Nightlight You can set a comforting nightlight on the Baby unit. There are three levels of brightness. 15 The Baby unit must be switched on for the nightlight to work, but doesn’t need to be linked to the Parent unit. Switch Baby unit nightlight on/off 1. To switch on, press either the or button. It will take 3 seconds to illuminate to the highest brightness level. button 2.
Using your BT Digital Baby Monitor 300 Do not press the button when the Baby unit and Parent unit are positioned in the same room. High-pitch noise will be generated if the button is pressed when the Baby unit and Parent unit are close to each other or within 3 metres distance. When using Talk back, hold the Parent unit approximately 30cm in front of your mouth when talking to baby. 1. Press and hold down the button on the Parent unit to speak to your baby.
Using your BT Digital Baby Monitor 300 17 List of tones Your Baby Monitor unit can produce various tones. They have the following meaning: Tone Meaning Single tone Confirmation tone e.g. setting saved. Double tone (fast) Error tone e.g. max volume reached when adjusting volume. Double tone (slow) User alert e.g. crying alert, paging alert etc. Triple tone (fast) System alert e.g. link lost, battery low etc. User Alert tones can be silenced by pressing any button on the Parent unit.
Using your BT Digital Baby Monitor 300 Resetting the units is only advisable if you are experiencing difficulties with your product. It is a useful feature that ensures your Baby Monitor is returned to its new “out of the box” settings. Reset the units Resetting either units will return the settings at that unit back to its default settings. Reset the Parent unit 1. Within 3 seconds of the Parent unit being switched button for at least 10 on, press and hold the seconds.
Help Helpline If you have any problems using your BT Digital Baby Monitor 300, call 0800 145 6789*. • • • • Parent unit is beeping Please see page 17 for the list of tones the Parent unit makes. The Parent unit will beep for a number of reasons: The link has been lost between your units, see page 11. Check that the Baby unit Link indicator is illuminated. If not, please ensure that the power adapter is still connected and if this still does not switch on, please test into a different electrical socket.
Help • Check units are within range of one another. • Check both units are turned on. • To speed up the charging process turn the Parent unit off when charging if it is not being used. Link indicator is flashing red • The Link between your units is broken. You will also hear an alert on the Parent unit to let you know there is no communication between the units. If this happens, check that the mains power (or batteries) is correctly connected and that the units are within range of one another.
General information Cleaning Both units have splash resistant grilles and casing. To clean, wipe with a damp cloth. Guarantee Your BT Digital Baby Monitor 300 is guaranteed for a period of 12 months from the date of purchase.
General information Returning your product If the Helpline is unable to remedy your problem they will issue a Fault Reference Authorisation number and ask you to return the product to your original place of purchase. Where possible, pack the product in its original packaging. Please remember to include all parts, including the power supply adapters and the original batteries. For guarantee purposes proof of purchase is required so please keep your receipt.
General information 23 R&TTE This product is intended for use within the UK. This equipment complies with the essential requirements for the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC. Declaration of Conformance Hereby, BT declares that this BT Digital Baby Monitor 300 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The Declaration of Conformance for the BT Digital Baby Monitor 300 is available from bt.
For a Better Future We’re always looking to make our products last longer and use less power, so we don’t have such a big impact on the environment. To find out about what we are doing, visit bt.com/betterfuture Offices worldwide The services described in this publication are subject to availability and may be modified from time to time. Services and equipment are provided subject to British Telecommunications plc’s respective standard conditions of contract.
