User guide

Your Additional Camera
B
T
V
i
d
e
o
B
a
b
y
M
o
n
i
t
o
r
Skip
Front
Camera
Infra red LEDs
Back-up light
for night vision.
Power on/off
Press and hold to
turn on or off.
Red light is on
when powered
by batteries.
Green light is on
when powered by
the power adaptor.
Orange light is on when
the Camera unit
is not paired to
the Parent unit.
Flashes red when
the battery is low.
Flashes red and green
alternately when
the Camera unit is in
pairing mode.
Camera angle
adjustment tab
Pull to adjust the
camera angle.
Light sensor
Press to play and
stop lullabies.
Volume +/-
Press to increase or
decrease the volume.
Skip
Press to skip to the
next lullaby.
Microphone
Back
Temperature sensor
Speaker
To listen to lullabies
and parent’s voice
when Talk feature
is used from the
Parent unit.
Power socket
Antenna
Battery
compartment cover
Threaded socket
(6mm)
Used for the wall
mounting bracket
supplied or a tripod
(not supplied).
2 Pairing and testing
You will need to pair your new Camera unit to your BT Digital Video 1000
Parent unit before you can use it. You can pair a maximum of four Camera
units to your Parent unit.
To pair the Camera unit to your Parent unit
1. Firstly, make sure the Camera and Parent units are turned on, by pressing and
holding the power buttons on each unit.
2. Press
on the Parent unit.
3. Press
or to highlight PAIR/UNPAIR CAM, then press or .
4. Press
or again to select Pair new CAM.
5. Press
or to choose a Camera unit slot, then press .
6. When the display shows Please press both
and keys on CAM side until
POWER indicator flashes Red and Green light, press and hold the and
buttons for 5 seconds on the Camera unit. The light on the button of
the Camera unit will flash red and green alternately.
7. When pairing has been successful, the screen will display the image from the
newly paired Camera unit. The light on the
button of the Camera unit
will turn red when it is powered by AA batteries or green when powered by the
power adaptor.
If pairing fails, the screen will display Pairing failed. Try the pairing procedure again.
If you pair a new Camera unit to an already occupied Camera unit slot it will
unpair the current Camera unit. Only one Camera unit can be paired at a time.
Testing the units before use
It is important that you test the units before use and at regular times thereafter,
especially if they have not been used for some time.
To test your units
1. Place the Parent and Camera units in the same room but make sure they are at
least 2 metres apart.
2. Press and hold the button on the Camera unit until the Power light on the
button turns on.
3. Press and hold the button on the Parent unit until the display shows
Waiting for linking and the Link light flashes.
4. Press the button on the Parent unit to view the image from the Camera unit.
If no connection can be established, the Parent unit will display No link to CAM for
a few seconds, then Waiting for linking… The Link light will continue to flash.
Positioning and operating range
Positioning
We recommend you place the Camera unit between 1-2 metres away from your
baby for best performance. Make sure the unit and cable is out of reach of your
baby. Do not place the Parent and Camera units too close together as you will
hear a high-pitched noise, this is normal. The units are designed to be located
at a distance from one another, e.g. in separate rooms.
Operating range
The operating range is up to 300 metres outdoors and 50 metres indoors.
The actual operating range may vary depending on the environmental conditions
and other interferences such as walls, doors and other obstructions.
3 Go!
Switch the Camera unit on/off
1. Press and hold the button until the light on the button turns on.
2. To turn the Camera unit off, press and hold the
button for 2 seconds. The
light will turn off.
Adjust the Camera unit loudspeaker volume
You can adjust the loudspeaker volume from Level 1 to Level 5. The default
setting is Level 3. If you adjust the loudspeaker volume it will also adjust the
parent voice (Talk) playback volume.
When the maximum or minimum volume levels have been reached you will
hear an error tone.
1. Press the
or button on the Camera unit at any time to increase or
decrease the loudspeaker volume.
Play lullabies from the Camera unit
The Camera unit has five lullabies that can be played to gently soothe your baby.
The total lullaby playback time is about 15 minutes and it starts from where you
stopped it last time.
To play lullabies
Press the
button to play.
Press the
Skip
button to skip to the next lullaby.
Press the
button to stop playback.
Lullaby playback will be paused if the Talk feature is being used from the
Parent unit, when finished lullaby playback will resume.
Night vision
To help you monitor your baby at night, the Camera unit automatically uses the
light from its infrared LEDs when it is turned on in a dark room. However, it only
transmits black and white images in this mode.
The LEDs on the Camera unit may glow red slightly in dark conditions,
this is normal.
To unpair a Camera unit from the Parent unit
1. Firstly, make sure both units are turned on, then press
on the Parent unit.
2. Press
or to highlight PAIR/UNPAIR CAM, then press or .
3. Press
or to select Unpair CAM, then press .
4. Press
or to select the Camera unit you want to unpair,
then press .
5. When the display shows, To unpair CAM # from the system, press
key,
press the button.
6. When the display shows, Press
key to confirm, press .
7. When unpairing has been successful, the screen will display the image from
the next paired Camera unit. If there is no paired Camera unit, the screen will
display NO CAM paired.