Datasheet

One-touch memory buttons (M1-M11)
Store your 11 most frequently used phone numbers on the grey one-touch memory
buttons for ease of dialling. Buttons 7-11 have been pre-programmed with the
following BT Services, however you can overwrite them with your own numbers.
M7 = Residential Directory Enquiries 118 500, M8 = Business Directory Enquiries
118 700, M9 = BT Answer 1571, M10 = Call Divert On, M11 = Call Divert Off.
Store/replace a one touch number
Lift the handset, or press
, to get a line.
Press and hold the grey memory button you want until you hear a beep and the
Secrecy light ashes.
Enter the number you want to store.
Press the same grey memory button to conrm. The number is stored.
You hear a conrmation beep. Pull out and use the memory label next to the
button to keep a note of the person’s name.
Dial a one-touch memory number
Lift the handset, or press
, then press the one-touch button you want.
The stored number is dialled.
Storing a pause in a number
A pause is normally inserted in a stored telephone number after a switchboard
access code (e.g. 9) to allow the switchboard time to get an outside line before
the number is dialled. For example,
9 – Pause – 08702405522.
To enter a pause, press
in the appropriate place when storing the number.
2 Go!
Making calls
Lift the handset and dial the phone number. Replace the handset to end the call.
Make a call using a headset
Headsets are not supplied. However, you can purchase headsets (with RJ11 jack)
by visiting www.shop.bt.com
Plug the headset into the socket marked
on the underside of the base.
Press
and dial the number. When the headset is in use the headset indicator
(on the button) will be lit.
Press
to end the call.
Receive a call using a headset
When the phone rings and the headset is plugged in, press
to answer.
Redial
Lift the handset, or press
, then press to redial the last number called.
Handsfree
Press
during a call to switch between earpiece and loudspeaker.
Secrecy
Press
during a call. The red secrecy light (on the button) comes on and your
caller cannot hear you. Press again to return to your caller.
Message waiting
If your BT Converse phone is connected to a switchboard, the message waiting indicator
will ash when you receive new voicemail messages.
BT 1571 or similar network voicemail users can also use this feature, however the
indicator light will not ash. New voicemail messages will be indicated by a stuttered
dial tone when you pick up the handset.
If your telephone is connected to a switchboard you may need to change the
message waiting switch setting on the base of the phone. It is pre-set to MW3
which is for an SX2000 switch. MW1 and MW2 positions are for when the telephone
is connected to an ISDX switch. If the switch is moved to MW2 and the message
waiting indicator stays on permanently, use MW1.
Lift the handset, or press
and dial , to connect to your
answering service.
Adjust the ringer volume
Set the Ringer Volume switch on the underside of the phone to 0 (Off), 1 or 2.
Adjusting the ringer tone
Set the Ringer switch on the underside of the phone to 1 (Low), 2 (Medium) or 3 (High).
Amplify
Press to switch the earpiece/headset volume to High. After you hang up,
the volume will automatically return to Normal volume.
Your phone
Help
Most problems can be xed with a few simple checks.
Problem Solution
No dial tone Only use the cables supplied.
Make sure the line cord is plugged into the correct socket.
You have a dial tone, but the
phone will not dial out
If you are connected to a switchboard, check whether
you need to dial an access code or if you need to change
the dial mode.
Phone ringer does not ring Is the ringer volume switch set to 0?
Move the ringer switch to 1 or 2.
Using broadband on the same
phone line?
Make sure you plug the phone
into the wall socket via an ADSL
microlter (not supplied), otherwise
you may have problems with this
product and your broadband service.
ADSL
microlter
Find out more
• New Frequently Asked Questions available at www.bt.com/producthelp
• If you need more detailed instructions, a full user guide is available to
download from www.bt.com/producthelp
Make and
receive calls
with a headset.
Indicator light is
on when in use.
R (Recall) for
use with a
switchboard and
some BT Calling
Features.
Make and
receive calls
handsfree.
Indicator light is
on when in use.
Adjust earpiece,
headset or
speaker volume
during a call.
Press to switch
earpiece/
headset volume
to High.
During a call,
press to stop
your caller
hearing you.
Indicator light is
on when in use.
Headset socket
(underneath
the phone)
Use to connect
a headset.
One touch
memory label
Keep a note of
your numbers.
The following
switches are
located on the
underside:
Dialling mode
Set the
dialling mode.
Message
waiting switch
Adjust if
connected to a
switchboard.
Ringer switch
Adjust the
ringer tone.
Ringer volume
switch
Adjust the
ringer volume.
Handset park
If phone is
wall-mounted,
hang the
handset here
if you need to
leave the phone
during a call.
Redials the last
number called.
Use to enter
a pause.
Store your
most important
one touch
number here.
Message
waiting
indicator
Flashes if you
have Voicemail.
1
Call indicator
Flashes when
you have an
incoming call.
10 one-touch
memory
buttons
(M2-M11)
Store and dial
one-touch
numbers.
Bottom 5
buttons are
pre-programmed
with BT Services
numbers.
1 The light will only ash when connected to a PBX switch or similar.
The light will not ash when used with network services. e.g. BT 1571.
Handset & Hearing Aid
Hearing aid wearers may benet from switching
their hearing aid to the middle T position and
holding the earpiece up to the aid, not their ear.
Please visit http://www.btplc.com/inclusion/ for
further practical advice on using hearings aids.