ENGLISH USER MANUAL OPERATION MANUAL ® Thank you for buying this BRITEQ product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit. FEATURES This unit is radio-interference suppressed. This product meets the requirements of the current European and national guidelines. Conformity has been established and the relevant statements and documents have been deposited by the manufacturer.
ENGLISH USER MANUAL SAFETY INSTRUCTIONS: CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
ENGLISH USER MANUAL The housing and the lenses must be replaced if they are visibly damaged. Please use the original packing when the device is to be transported. Due to safety reasons it is prohibited to make unauthorized modifications to the unit. Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy. DESCRIPTION: 1. Projector with hard plastic cover to protect the LEDs.
ENGLISH USER MANUAL INSTALLING THE BATTERY The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. To keep the battery in good condition it should be recharged immediately after it was discharged! Never store a discharged battery for a longer period! The battery should always be used in horizontal position, ventilation must be provided during charging and use of the battery.
ENGLISH USER MANUAL INSTALLING THE (OPTIONAL) W-DMX MODULE Important: The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and mechanical safety in your country. Unpack the “LDP-WDMX-ACCUSPOT” module (W-DMX module): it consists of an antenna with nut and the actual W-DMX PCB. Switch the projector off and remove the mains cable. On the projector: remove the 4 screws of the blind plate where the WDMX module will be installed.
ENGLISH USER MANUAL Remark: You can connect a JBS CA-8 remote controller to the master unit if you want to have more control over the master/slave operation. You can also connect the JBS LEDCON-02 remote controller Electrical installation for two or more units in DMX-mode: You can control the LDP-ACCUSPOT by DMX in different ways, depending on your needs.
ENGLISH USER MANUAL Note: when a DMX-signal is detected on the DMX-input connector, this “wired” DMX-signal will take precedence over the wireless DMX-signal. USING THE (OPTIONAL) COVERS The LDP-ACCUSPOT 7TC comes in black color, not always the best choice while placed in front of a white wall. Therefore you can buy optional plastic covers to put around the projector.
ENGLISH USER MANUAL “ShoW” Show Mode Used to choose to select one of the preprogrammed multi channel shows when used in standalone or master/slave mode. Press the MENU button until “ShoW” is shown on the display. Press the ENTER button to select. Use DOWN and UP buttons to select one of the preprogrammed shows: “Sh 1” all shows played in random mode. “Sh 1” to “Sh12” 12 different built-in shows.
ENGLISH USER MANUAL “ChMd” Channel Mode The unit has 5 different channel modes, refer to the DMX-chart to see the differences. Press the MENU button until “ChMd” is shown on the display. Press the ENTER button to select. Use DOWN and UP button to select one of the available channel modes. Once the mode is selected, press the ENTER button to confirm. Press the MENU button for about 2 seconds to return to running mode.
ENGLISH USER MANUAL Once the mode is selected, press the ENTER button to confirm. Press the MENU button for about 2 seconds to return to running mode. “Led” Led Display Display on: display is always on. Display off: display is off when not used. Press the MENU button until the display shows “Led”. Press the ENTER button. Use DOWN and UP buttons to select “ on “ (display always on) or “oFF “ (display off when not used). Once the mode is selected, press the ENTER button to confirm.
ENGLISH USER MANUAL C. Connect the optional JBS CA-8 controller for more control: The JBS CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the JBS CA-8 input of the first unit (master). Now you can control all the connected units: BUTTON STANDBY FUNCTION MODE ACTIONS To blackout all the fixtures 1.Synchronous strobe in white color 2.The same color chase 3.Different color strobe Strobe (LED OFF) Select one of the different colors.
ENGLISH USER MANUAL Channel mode 5: MAINTENANCE Switch off the unit and unplug the mains cable. During inspection the following points should be checked: When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced. The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected. In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly.
ENGLISH USER MANUAL SPECIFICATIONS Mains Input: Power consumption: Fuse: IEC input/output daisy chaining: Rechargeable battery: Battery dimensions: Sound Control: DMX connections: LEDs: Beam angle: Size: Weight: 100-240V, 50/60HZ 32 Watt 250V T6,3A slow blow (20mm glass) 40pcs 12Vdc / 24Ah 166 x 175mm, height = 125mm Internal microphone XLR 3pin 7 LEDs 3IN1 3W 25° see drawing below 5.
