Full Product Manual

7. Make sure the bottom end of the Water Straw
reaches the lowest part of the water jug (fig. 3).
Straw reaches the side of the jug at its lowest
point to ensure all of the water can be utilized.
Note: Most standard shaped water jugs have a
raised center at the very bottom. For maximum
efficiency, make sure the Water Straw reaches the
side of the jug at its lowest point to ensure all of
the water can be utilized (fig. 3).
8. Slide jug into the storage area and close
the Lower Door.
9. Plug cord into a properly grounded wall outlet.
The pump will now turn on and take up to 4
minutes to fill the internal tanks for the first time.
The pump will stop automatically when filled.
10. When the pump has stopped running turn the Hot Water and Cold
Water ON/OFF Switches (see # 12 and 13 on the Parts and
Features list) to the ON position. The Hot and Cold Water Indicator
Lights (see A and C on the Parts and Features list) will illuminate.
Note: Allow up to 1 hour for heating and cooling cycles to complete
and water to reach the proper hot and cold temperatures. The Hot and
Cold Water Indicator Lights will shut off when each cycle is complete.
11. Place a glass under the Water Dispensing Spigot (see # 5 on the
Parts and Features list).
12. After inserting a new filter, there may be a few bits of black
activated charcoal from the new filter present in the water glass.
This is common with new filters.
13. For cold water, press/hold the Cold Water Dispensing Button (see
#3 on the Parts and Features list) until the desired amount of
water has been dispensed, then release.
13. The Hot Water dispensing button
features a Child Safety Lock. To dispense
hot water, push the red safety lock in,
then push/hold the dispensing button
down until the desired amount of
water has been dispensed, then release.
Refilling an Empty Jug
When the water jug is empty, the cooler will attempt to pump water
for 2 minutes. After this time, the pump will stop and light the furthest
right on the upper panel will be on. This is your notification to refill
the empty jug. If this light is on and jug is not empty, it is notification
to change the BRITA filter.
1. Open the Lower Door.
2. Remove Water Straw and take empty jug out of the cooler.
3. Install a new jug by following the instructions for "Refill empty jug"
(Page 5).
BRITA Filter Replacement
• Replacement Cartridge BRITA Model No. FR-200
For use in the TCL-BR-1 Self-Filtering water cooler.
Thank you for choosing BRITA , the world’s No. 1 brand of household
water filtration. BRITA’s certified water filtration systems turn ordinary
tap water into cleaner, great-tasting drinking water. Just follow these
easy instructions to quickly install your BRITA Replacement Filter.
Replacing the BRITA Filter is easy. On the upper panel of your BRITA
Water Cooler, the furthest light to the right is the indicator for 2 func-
tions: 1) It will blink when your water jug is empty and needs to be
refilled. 2) If your water jug is not empty and the light furthest to the
right on the upper panel is blinking, it means that it is time to replace
your BRITA Filter. Prompt filter replacement helps to assure you of
cleaner, great-tasting water
.
Filter Replacement
1. The unit does not need to be unplugged, just slide the large water
jug out from behind the bottom door.
2. Holding the filter at the top with your fingers, gently pivot only the
filter toward you. It will easily pivot down when gently pulling on
only the filter, at the top, and pulling filter toward you.
Draining the Reservoirs
WARNING: BURN HAZARD. The product heats water to a temperature
of approximately 95° C / 203° F. Water temperatures above 52° C / 125° F
can cause severe burns or death from scalding. Children should be
supervised by an adult when using this product.
Drain the reservoirs before and after cleaning, before long vacations
or if not using the cooler for a long period of time.
1. Unplug the cooler.
2. Open the Lower Door and remove jug from cooler.
3. Remove the Water Straw from the water jug.
4. Place a container under the Water Dispensing Spigot. Press and
hold the Hot and Cold Dispensing Buttons until water no longer
comes out.
5. Place a container directly under the Drain Valve
(#14 on the Parts and Features list) on the back of
the cooler.
6. Remove the Drain Valve cap and drain valve
plug and let the water flow into the container.
7. Replace the Drain Valve cap and plug.
8. Replace the water jug.
9. Plug in the cooler.
LIMITED WARRANTY
This warranty applies to products purchased and used in the U.S. and
Canada. This is the only expressed warranty for this product and is in lieu of
any other warranty or condition.
This product is warranted to be free from defects in material and
workmanship for a period of one (1) year from the date of original purchase.
During this period, your exclusive remedy is replacement of this product or
any component found to be defective at our option; however, you are
responsible for all costs associated with returning the product to us and our
returning a product or component under this warranty to you. If the product
or component is no longer available, we will replace with a similar one of
equal or greater value.
This warranty does not cover glass, filters, wear from normal use, use not in
conformity with the printed directions, or damage to the product resulting
from accident, alteration, abuse, or misuse. This warranty extends only to the
original consumer purchaser or gift recipient. Keep the original sales receipt,
as proof of purchase is required to make a warranty claim. This warranty is
void if the product is used for other than single-family household use or
subjected to any voltage and waveform other than as specified on the rating
label (e.g., 115V ~ 60 Hz).
We exclude all claims for special, incidental, and consequential damages
caused by breach of express or implied warranty. All liability is limited to the
amount of the purchase price. Every implied warranty, including any
statutory warranty or condition of merchantability or fitness for a particular
purpose, is disclaimed except to the extent prohibited by law, in which case
such warranty or condition is limited to the duration of this written
warranty. This warranty gives you specific legal rights. You may have other
legal rights that vary depending on where you live. Some states or provinces
do not allow limitations on implied warranties or special, incidental, or
consequential damages, so the foregoing limitations may not apply to you.
To make a warranty claim, do not return this appliance to the store.
Call BRITA Customer Service at 716.235.1300 or toll-free at 1.800.256.8169 in
the U.S. and Canada. For faster service, locate the model #, serial #, and
manufacture date on your appliance.
Problem
No hot and/or
cold water.
No water
dispenses from
spigot.
Water Cooler
leaks.
Possible Causes
1. Cooler is
unplugged.
2. The Cold and/or
Hot Water ON/OFF
Switches (see # 12
and 13 on the
Parts and Features
list) are in the OFF
position.
1. Cooler is
unplugged.
2. Cold and/or Hot
Water Dispensing
Buttons are
disconnected on
inside of unit.
3. The circuit breaker
is tripped.
Cold tank lid is loose.
Solution
1. Push plug completely
into outlet.
2. Turn the Cold and/or
Hot Water ON/OFF
Switches to the ON
position.
1. Push plug completely
into outlet.
2. Remove Top Cover
and reconnect
button components.
See additional
troubleshooting
guide or call
Customer Service.
3a. Replace fuse or
reset circuit breaker.
3b. If too many items
are plugged into a
single outlet, move
some items to a
different outlet.
Remove Top Cover
and make sure cold
tank lid is secure.
1-800-256-8169
1-716-235-1300
Cleaning the Condenser
To improve cooling and efficiency, vacuum or sweep away the dust
from the Condenser Coils (see # 11 on the Parts and Features list) on
the back of the cooler. You can purchase a brush designed
specifically for this purpose from your local appliance store.
Troubleshooting the Water Cooler
1. Push red Child Safety Lock in.
2. Press the Hot Water Button down
while holding Child Safety Lock in.
1
2
fig. 3
fig. 2
TCL Products LLC,
300 Hylan Drive, Ste 198, Rochester, NY 14623
BRITA is a registered trademark
of Brita LP, used under license
by TCL Products LLC.
3. Reverse the process in #2 above to replace the old filter with a
new filter, finishing with pivoting the new filter, already attached to
the base, into its upright position. It will “click” into place when it
is in its correct upright position.
4. Slide the water jug back into place, and be sure to close the door
all the way. If the door is not closed completely, the unit will not
pump water, so be sure to close the door completely.
9
10
6
7 8