Instructions / Assembly

ManualsBrandsBrio ManualsFaucet Water FiltersReverse Osmosis Faucet Mount Water Filtration System, 700 GPD, 2:1 Pure to Drain, Tank-Less, Under Sink

Tankless RO Filtration System

Setup Manual

Model No.: ROSL700

G20-U

Summary of content (14 pages)

PAGE 1
G20-U Tankless RO Filtration System Setup Manual Model No.
PAGE 2
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Features . . . . .
PAGE 3
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing, and operating this filtration system. • If the power cable is damaged, do not use. Contact Customer Service for a replacement. • Avoid storing in an area exposed to intense sunlight as this can cause damage to components. • Do not store or expose the device in temperatures lower than 32°F (0°C). The ideal temperature range is 39°F - 100°F (4-38°C).
PAGE 4
Intended Use This appliance is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices, and other working environments • Farm houses • Clients in hotels, motels, and other residential type environments • Bed and breakfast type environments • Catering and similar non-retail applications This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless the
PAGE 5
Indicator Panel Description 1. Filter indicator lights – When blinking, indicates it is time to change filters (RO or PCB). 1 RO 2. Reset button – Press to reset the system after changing filters. PCB 3. Flush button – Press to flush newly installed filters. Reset Flush 2 Product Dimensions Height Width Depth 42 cm (16.5 in.) 13.2 cm (5.2 in.) 46.1 cm (18.2 in.) Materials Needed Wrench Electric drill with 1/4 in.
PAGE 6
Package Contents I A F B J E K D H C L G Part Description M Quantity Part Description Quantity A RO filtration system 1 H Drain saddle 1 B Faucet 1 I RO water outlet tube 1 C Power adapter 1 J Shut-off valve tube 1 D Feed water adapter 1 K Faucet tubing 2 E PCB filter 1 L 1 F RO filter 1 2/8 - 3/8 in.Quick connect M 2/8 in. Quick connect 2 G Plumbers tape 1 Installation 1.
PAGE 7
2. Connect to the Cold Water Supply CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your filters. D. Turn off and then disconnect the current cold water supply line. E. Connect the feed water adapter (D) to the cold water supply line. D F. Connect the cold water supply line on top of the feed water adapter (D).
PAGE 8
3. Make the Reverse Osmosis Waste Connections The “RO” filter assembly requires a drain line connection to be installed, which removes rejected water to the sewer. The drain saddle connects the drain line from the dispenser to your drain pipe. The drain saddle is designed to fit around a standard 1.5 in. OD (outer diameter) drain pipe. Always install the drain saddle before the P-trap and on a straight vertical or horizontal section of the pipe.
PAGE 9
4. Install the faucet A. Ensure that you have a faucet mounting hole in your sink or sink countertop for this faucet. If you do not, create a mounting hole no less than 1 – 1.2 in. (26 – 30 mm). B. Remove the washer (1) and lock nut (2) from the faucet. Ensure that you leave the O-ring (3) on the faucet. C. Attach the two 2/8 in. quick connects (M) to the large faucet post (filtered water) and the short faucet post (tap water). 3 1 2 M M D.
PAGE 10
5. Complete the Installation A. Connect the shut off valve tube (J) to the inlet water connection (1). B. Connect the faucet tubing (K) connected to the 2/8 in. quick connect (M) to the filtered water connection (2). C. Connect the faucet tubing (K) connected to the 2/8 in. quick connect (M) to the purified water connection (3). D. Connect the RO water outlet tube (I) to the waste water connection (4). E.
PAGE 11
Troubleshooting Problem Probable cause Solution The filter is generating a light noise during operation. The filter can generate a light noise during operation. This is normal. The water output volume has dropped. • The filter is jammed. • Flush or replace the filter. • The filter needs to be replaced. • Replace the filter. • The ball valve or faucet is not completely turned on. • Check the water inlet ball valve, or the faucet to ensure they are turned on completely.
PAGE 12
Filter Replacement Schedule Filter Type Replacement Schedule Function PCB Composite Filter (PAC and Carbon) 12 months Removes mud, sand, rust, suspended materials, residual chlorine, and abnormal flavor from water. RO Filter 24 months Removes up to 99% of contaminants including arsenic, lead, fluoride, heavy metals and more. Replace the Filters When the filter indicator light on the indicator panel flashes, it indicates that one of your filters needs to be replaced. 1.
PAGE 13
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Filters (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.