Point of Use Water Dispenser Setup Manual Model No.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Features . . . . .
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating this dispenser, always exercise basic safety precautions, including the following: • Prior to use, this dispenser must be properly assembled and installed in accordance with this manual. • For indoor use only.
Intended Use This appliance is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices and other working environments • Farm houses • Clients in hotels, motels and other residential type environments • Bed and breakfast type environments • Catering and similar non-retail applications This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they h
Indicator Panel Description 1. Power indicator light – When illuminated, indicates that the dispenser is on. 2. Hot water indicator light – When illuminated, indicates that the dispenser is heating water. 3. Cold water indicator light – When illuminated, indicates that the dispenser is cooling water. 4. Water indicator light – When blinking, indicates that the dispenser is not connected to a water line or is not receiving water from the water line. 1 2 3 Product Dimensions Height Width Depth 105.
Installation 1. Determine Installation Location A. Place the dispenser upright. B. Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. NOTICE: Do NOT plug in the power cord until the entire installation section is completed. C. Position the back of the dispenser no closer than 20 cm (8 in.) from a wall and permit free airflow between the wall and water dispenser. 2.
E. Gently tug on the tube (B) to ensure a secure connection with the feed water adapter (E). E B 3. Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A. Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. C D B. Connect the tip of the shut-off valve tube (B) to the left side of the filter housing (C). C B C.
4. Install the Filters and Complete the Installation A. After flushing, twist each filter (D) clockwise into the filter housings located inside the dispenser cabinet. The sediment filter goes on the left, the carbon filter on the right. D B. Remove the safety plug from the water inlet hole on the back of the dispenser by pushing in the inlet hole collar and then gently pulling out the plug. C. Connect the tip of the shut-off valve tube (B) into the water inlet hole on the back of the dispenser.
Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate the hot and cold switches, ensure water has filled the tanks inside the dispenser in order to prevent dry heating. 1. Plug in the dispenser and turn the On/Off switch to On. 2.
Troubleshooting Problem Solution • It takes up to one hour after setup to dispense cold water. • Make sure the power cord is properly connected to a working outlet. The cold water is not cold. • Make sure the back of the dispenser is at least 20 cm from a wall and there is free airflow on all 20 cm sides of the dispenser. • Make sure green power switch on back of dispenser is On. • If water still isn’t cold, call customer service at +1 844-257-4103 for assistance.
Clean the Dispenser CAUTION: Before cleaning, make sure the power switch is in the O (off) position and unplug the water dispenser. IMPORTANT: This dispenser contains UV technology that will help keep your dispenser clean. However, if you do need to clean your dispenser for any reason, follow these steps: 1. Remove remaining water from reservoirs in the dispenser by dispensing from the hot and cold taps into a pitcher or bucket. 2. Remove the top cover (1), cold tank cover (2), and separator (3). 3.
Filter Replacement Schedule Filter Type Replacement Schedule Function Carbon 6 months or 950 gallons Reduces chlorine, taste and odor, lead and cysts. Sediment 6 months or 950 gallons Performs a coarse filtration of original water. Removes mud, sand, iron, rust, and suspensions, and impurities. Replace the Filters IMPORTANT: Only replace the filters with new filters designed for this dispenser. Any other type of filter will damage the machine and void any warranty.
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.
Contact Us Call: +1 844-257-4103 ©2020 DTWUSA
