AC6368A Datasheet 1、Pin Definition 1.1 Pin Assignment Figure 1-1 AC6368A Package Diagram 3 Confidential The information contained herein is the exclusive property of JIELI and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of JIELI.
AC6368A Datasheet 1.2 Pin Description Table 1-1 PIN I/O Drive Type (mA) VBAT P / Battery Power Supply VDDIO P / IO Power 3.3v Name NO.
AC6368A Datasheet 2、Electrical Characteristics 2.1 Absolute Maximum Ratings Table 2-1 Symbol Parameter Min Max Unit Topt Operating temperature -40 +85 °C Tstg Storage temperature -65 +150 °C VBAT Supply Voltage -0.3 3.6 V V3.3IO 3.3V IO Input Voltage -0.3 3.6 V Note : The chip can be damaged by any stress in excess of the absolute maximum ratings listed below 2.2 Recommended Operating Conditions Table 2-2 Symbol Parameter Min Typ Max Unit VBAT Voltage Input 2.2 3.0 3.
AC6368A Datasheet 2.4 Internal Resistor Characteristics Table 2-4 General Output Port Internal Pull-Up Resistor High Drive Internal Pull-Down Resistor PA6 PB1 8mA 24mA 10K 10K USBDP 4mA _ 1.5K 15K USBDM 4mA _ 180K 15K 2.5 Comment 1、PB1 default pull up 2、USBDM & USBDP default pull down 3、internal pull-up/pull-down resistance | accuracy ±20% BT Characteristics 2.5.
AC6368A Datasheet 2.5.
AC6368A Datasheet 3、 Package Information 3.1 SOP8 Figure 3-1 AC6368A Package 8 Confidential The information contained herein is the exclusive property of JIELI and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of JIELI.
FCC WARNING FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. The final end product must be labelled in a visible area with the following: “Contains Transmitter Module 2A4AM-BP-B01” The module can be used for BUBBLE MASSAGE BATH APPLIANCE with 0dBi antenna.
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See alsoSection 2.
module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured.
The module manufacturers shall provide a list of acceptable unique connectors. Explanation: The EUT has one PCB antenna, the antenna can't be replaced by other authorized antennas. 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating “Contains FCC ID” with their finished product.
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Explanation: The module without unintentional-radiator digital circuity, so the module does not require an evaluation by FCC Part 15 Subpart B. The host shoule be evaluated by the FCC Subpart B.
