Hardware User’s Manual Megapixel Day & Night Fixed Box Network Camera Quality Service Group Fixed Box Series 0
Review History: 1. Separate User Manual into HW and SW. 2. Merge FB-100Ap/FB-100Ae/FB-130Np Series into this User Manual. Product name: Network Camera (Fixed Box series) Release Date: 2011/12 Manual Revision: V3.0 Web site: www.brickcom.com Email: technical@brickcom.com info@brickcom.com ©2011 Brickcom Corporation.
Table of Contents Before You Use This Product ..................................................................... 3 Regulatory Information ............................................................................ 4 Chapter 1- Package Contents .................................................................... 5 Chapter 2- Fixed Box Network Camera Overview ........................................... 6 Chapter 3-LED Behavior ...........................................................................
Before You Use This Product In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network Camera is a high-performance, web-ready camera which can be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of this camera is legal before installing this unit for its intended use. Upon opening the product’s package, verify that all the accessories listed on the “Package Contents” are included.
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Chapter 1- Package Contents Please check to make sure that the product package contains all the accessories listed below. a. Network Camera b. CS mount Lens (Optional) c. Product CD d. Camera Stand e. Warranty Card f. Allen Key g. Power Adapter (Optional) h. Easy Installation Guide i.
Chapter 2- Fixed Box Network Camera Overview The Brickcom Fixed Box series offers a reliable and efficient solution for 24-hour video surveillance. The Fixed Box series offers highly efficient H.264 video compression, which reduces bandwidth and storage requirements without compromising image quality. M-JPEG and MPEG-4 are also supported for flexibility. With the megapixel progressive sensor and removable IR-cut Filter, this series delivers extremely clear and detailed images that CCTV cameras cannot offer.
Chapter 3-LED Behavior Function LED Behavior Description WPS WPS in progress WPS WPS Connection Error WPS Session overlap detected WPS WPS Successfully Connected Steady on Remark Wireless Fixed Box Front Right (Blue) Wireless Fixed Box Front Right (Blue) Wireless Fixed Box Front Right (Blue) Wireless Fixed Box Front Right (Blue) Status Hardware failure Front Left (Green) Status 1. Restoring settings 2. Normal Operation Front Left (Green) Status Continuous Illumination 1. Power Off 2.
Chapter 4- Device Appearance Description Photo Indication & Dimension Diagram Status LED Power Connector (AC24V In) Microphone/Line In Ethernet RJ45 10/100 Socket Power Connector (DC24V In) (Link/Power LED embedded) Light Sensor Detachable Antenna WPS LED WPS Button SD/SDHC Card Slot Extension I/O Terminal Block Reset Button Audio Out Build-in Microphone Auto Iris Connector NOTE 1. The WPS buttons must first be enabled through the web GUI in order to work.
(DC Drive) --- CS Mount Zoom Controller Focus Controller Extension I/O Terminal Block The Network Camera provides an extension I/O terminal block which is used to connect the camera with external input/output devices. The pin definitions are listed as below.
Hardware Reset Reset Button The Reset Button can be used to reboot the camera or restore it to factory default settings. If the camera experiences a problem, rebooting the camera may correct the problem. If the problem remains, please restore the camera to factory default settings and reinstall the software. To Reboot - Press and hold the Reset Button for one second using a paper clip or thin object. Wait for the camera to reboot.
Chapter 5- Installation 5.1 Hardware Installation Mounting the CS-Mount Lens to the Camera --- Optional Lens Connect the CS-mount lens to the camera by turning it clockwise onto the camera mount until it stops. If necessary, adjust the iris controller, focus controller, and zoom controller to get the best resolution. To adjust the lens: Adjust the iris ring controller to control the amount of light coming through the lens.
--- Optional Lens Connect the CS-mount lens to the camera by turning it clockwise onto the camera mount until it stops. If necessary, adjust focus controller, and zoom controller to get the best resolution. Connect the lens cable plug (DC Iris control cable) to the camera side connector. To adjust the lens: The zoom controller can be manually adjusted to control the zoom factor on the camera. Users can create a tighter or wider view of the site being recorded.
5.2 System Requirements Operating System: Microsoft Windows XP Home Edition SP2 Microsoft Windows XP Professional SP2 Computer: IBM PC/AT Compatible CPU: Pentium 3GHz or faster Memory: 1024 MB or more Monitor: 1024 x 768 pixels or more, 24-bit True color or better Network Interface: 10/100Mbps Network interface card must be installed Web Browser: Microsoft Internet Explorer 6.0 SP2 or higher Adobe Reader: Adobe Reader 8.
5.3 Camera Connection Basic Connection (Without PoE) To attach external devices, such as sensors and alarms, connect them to the extension I/O terminal block. Connect the camera to a switch using an Ethernet cable. Connect the supplied power cable to the camera and plug it into a power outlet. Depending on the user’s application, an Ethernet cable may be needed. The Ethernet cable should meet the specs of UTP Category 5 and not exceed 100 meters in length.
If using a non-PoE switch: Use a standard RJ-45 cable to connect the camera to a PoE Injector. Use a standard RJ-45 cable to connect the PoE Injector to the non-PoE switch. Use a standard power cable to connect the PoE Injector to a power outlet. Software Installation In this manual, "User" refers to whoever has access to the Network Camera, and "Administrator" refers to the person who can configure the camera and grant user access to the camera.
In the Install Shield Wizard dialog box, click to continue. Read the End-User License Agreement and check the option “I accept the terms of the license agreement”. Click to continue.
Select either “Complete” setup or “Custom” setup to install the system. If COMPLETE SETUP is selected: All program features will be installed into the default directory. Check the option “Complete” and then click . Click to change the appointed folder where installation and program files will be stored. Click to continue.
Select to create shortcuts. Click to continue. The installation information will be displayed. Click to continue.
To launch EasyConfig or PC-NVR Standard, select the application and click . When launching the PC-NVR program, please refer to the PC-NVR user manual. If CUSTOM SETUP is selected: This option is recommended for advanced users. It can be used to install the system to a preferred directory or to select specific program feature(s). Check the option “Custom”, and then click .
Select the features to install. Click to continue. Click to change the appointed folder where installation and program files will be stored. Click to continue.
Select programs to create shortcuts. Click to continue. The installation information will be displayed. Click to continue.
To launch EasyConfig or PC-NVR Standard, select the application and click . When launching the PC-NVR program, please refer to the PC-NVR user manual. EasyConfig To launch EasyConfig, select EasyConfig from the start menu. If Complete Setup type was used in the software installation, an EasyConfig icon was installed on the desktop. Double click to open the icon.
If Custom Setup type was used in the software installation and an EasyConfig icon was not installed on the desktop, the program will be installed under C:\Program Files\Brickcom\EasyConfig unless the program was saved to a preferred directory. Click to continue. The program will automatically search for the camera in the intranet. NOTE - Check “Skip the hardware installation guide” to skip checking the hardware connection. To check the hardware installation settings, do not check the option box.
Select either “Simple Mode” or “Professional Mode” to obtain the camera’s IP settings. If “Simple Mode” is selected, EasyConfig will set up the connection automatically. If “Professional Mode” is selected, the user will need to configure the IP settings manually.
There may be many cameras in the local network. Differentiate the cameras using their UPnP name. Double click on the camera from the survey list to connect. For configuring the IP address settings, select either , or . The DHCP setting is recommended.
If is selected, the following pages will be displayed.
If the camera supports the EasyLinkTM function, the following page will be displayed. Otherwise, this page will not be shown. *If desired, click to skip this setting. EasyLinkTM is a unique Brickcom function which allows users to assign a unique EasyLink name to their network camera’s IP address. There is no need to configure the router to open up ports or remember hard-to-memorize IP addresses. Users can log onto [uniqueEasyLinkname].mybrickcom.com to view the camera’s web GUI and live view.
If “Static IP address settings” was selected, the failure page will be displayed as below: If the connection was successful, the user will see the message: “Congratulations. The installation of the camera is complete.” When this window is displayed, click to start the PC-NVR program, to view the live video from the connected IP camera, or in the top right corner of the screen to close the installation window.
Once installation is complete, the Administrator should proceed to the next section "Accessing the Network Camera" for necessary changes and configurations.
