Network Camera Brickcom Software User’s Manual
Brickcom Matrix CB-Series CB-100Ap,CB-100Ae,CB-101Ap,CB-101Ae,CB-102Ap,CB-102Ae WCB-100Ap,WCB-100Ae WCB-500Ap,WCB-400Ap,WCB-300Ap,WCB-200Ap,WCB-130Ap CB-500Ap,CB-400Ap,CB-300Ap,CB-200Ap,CB-130Ap WCB-502Ap,WCB-402Ap,WCB-302Ap,WCB-202Ap,WCB-132Ap CB-502Ap,CB-402Ap,CB-302Ap,CB-202Ap,CB-132Ap FB-Series WFB-100Ap,WFB-100Ae,WFB-130Ap,WFB-130Np,WFB-300Ap FB-100Ae,FB-100Ap ,FB-130Ap,FB-130Np, FB-300Ap MD-Series MD-500Ap,MD-400Ap,MD-300Ap,MD-200Ap,MD-130Ap,MD-100Ae,MD-100Ap MD-130Np ,MD-200Np, MD-300Np FD-series FD-
WOB-100Ae,WOB-100Ap,WOB-130Np GOB-100Ap,GOB-130Np OB-500Ap, WOB-500Ap, GOB-500Ap OB-502Ap,OB-402Ap,OB-302Ap,OB-202Ap WOB-502Ap,WOB-402Ap,WOB-302Ap,WOB-202Ap GOB-502Ap,GOB-402Ap,GOB-302Ap,GOB-202Ap OB-500Af,OB-400Af,OB-300Af,OB-200Af,OB-130Af,OB-100Af OSD-Series OSD-040D/E PT-Series PZ-040D/E
Product name: Network Camera Release Date: 2012/03/27 Web site: www.brickcom.com Email: support@brickcom.com info@brickcom.
Feature Model Name Live View All Series Camera/Video/Audio Camera Control Camera All Series Video All Series Audio All Series Multicast All Series Privacy Mask Control CB Series Professional Preset Point OSD-040 Series Privacy Mask PZ-040 Series Patrol Settings Network Event IP Settings All Series UPnP All Series EasyLink All Series Wireless Wireless model 3G 3G model HTTP/HTTPS All Series Event Settings All Series Motion Detection All Series PIR CB Series Professional
Samba Settings All Series HTTP Settings All Series Digital Output (DO) This function only available for the models with a Do terminal Video Clip All Series Audio Clip(*) This function only available for models with a audio in or build-in MIC System LED Light(*) CB- Series Professional System Log All Series Date and Time All Series Device Information All Series Storage Management This function only available for models with a SD slot.
Table of Contents Authentication ............................................................................................................................ 1 Installing the Plug-In ................................................................................................................. 2 Live View ....................................................................................................................................... 3 Configuration ...................................................
LED Light (*) .............................................................................................................. 63 System ................................................................................................................... 64 System Log ............................................................................................................... 64 Date and Time ...........................................................................................................
Authentication To access the camera’s live view, open a web browser and enter the IP address of the camera. A dialog window will pop requesting a username and password. As stated on the previous page, for the default username and password for the Administrator are assigned as “admin/admin”. For accounts other than the administrator’s account, the user can choose to remember the password for future convenience. It is not recommended to check this box when viewing the camera feed from a public computer.
Installing the Plug-In For the initial access to the camera in Windows, the web browser may prompt the administrator for permission to install a new plug-in for on Internet Explorer. Permission request depends on the Internet security settings of the user’s PC or notebook. If the highest security level is set, the computer may prohibit any installation and execution attempt. This plug-in has been registered for certificate and is used to display the video in the browser. Click on to proceed.
Live View NOTE - (*) These are optional features. Please refer to the Product List for the full list of optional features available for the product. Live View is the default page that opens when accessing the camera. Live video is displayed directly in the browser window. Stream 1~3 Channels The network camera offers simultaneous several streams for optimized quality and bandwidth.
TCP - This protocol guarantees the complete delivery of streaming data and provides better video quality. The downside of using this protocol is that the quality of its real-time effect is less than that of the UDP protocol. UDP - This protocol allows for more real-time audio and video streams. However, network packets may be lost due to network burst traffic and images may be broken. Activate UDP connection time-sensitive responses are more important than video quality.
Digital Zoom - Enable the digital zoom operation. Mirror - Horizontally reflect the display of the live video. Flip - Vertically reflect the display of the live video. Real Size - View the object in real size. Press it again to switch back to normal mode. Full Screen - Switch to full screen mode. Press the “Esc” key to return to normal mode. Motion Detection Alert - Enable the motion detection alert function. Mute – Turn off the sound. Talk(*) – To communicate through the camera using the computer MIC.
Recording folder path - The destination for saving the recording video files. Click Browse to specify the saving path. Snapshot folder path - The destination for saving the snapshot files. Click Browse to specify the saving path and select the format from the drop-down menu. NOTE 1. The functions have no effect on the recorded video. Whatever changes are made to the will not be applied to the recorded video.
Configuration Click on the main page to change the camera settings pages. NOTE - Only Administrators can access the Configuration page. Camera/Video/Audio Camera Profile – Up to five profiles can be created for different lighting environments. night are default profiles and users can create up to three additional profiles. Day and Select a profile from the drop-down menu or select different icons to change profile settings.
Sharpness - Drag the bar to adjust the image sharpness level from -5 to +5. Saturation - Drag the bar to adjust the image saturation level from -5 to +5. Exposure Control Auto: The camera will automatically control exposure. Manual: Select this option to define the exposure manually Metering Option - Center-weighted average metering. Flicker-Free – Eliminates the problem of flicker. De-Noise Auto - The camera will automatically filter the frame-to-frame defects to reduce the visual impact of blur.
Profile Management: Profiles can be scheduled to change at scheduled times or under different lightening changes. Always- Select Always to use a single profile. Select the profile from the drop down menu. Day & Night (*) (This function only available for models with a light sensor) - Select Day & Night to schedule two profiles for day and night. Select profiles from the drop down menu for the Day and Night Profiles.
Schedule – Select Schedule to schedule specific time periods for different profiles. Digital Inputs (*) (This function only available for models with a DI terminal) - Select Digital Input to have the profile management controlled by an external sensor. Select profiles from the drop down menu. Profiles will change according to different trigger voltage levels. Click Apply to apply settings or Cancel to cancel changes. Video The Network Camera offers several separate streams for different viewing options.
Stream Video Codec - The Network Camera offers three choices of video codec standards for real-time viewing: H.264, MPEG-4 and MJPEG. Video Resolution - Select from the drop-down menu to choose the best resolution for your application. Frame Rate - Select the frame rate from drop-down menu. When selecting from Video Codec option, the frame rate ranges from 1 to 30 fps. Set a higher frame rate for smoother video quality.
Click Apply to apply settings or Cancel to cancel changes.
Video Overlay Timestamp To display the date and time on the screen during live view, check “Enable” to enable the timestamp function and select the display position from the drop-down menu. Format: YYYY-MM-DD. If Timestamp enable is selected, select the Date Format from the drop-down menu. Text To make a note about the camera, check “Enable” and select the display position from the drop-down menu. Enter a video description in the text box. Click Apply to apply settings or Cancel to cancel changes.
RTSP Server To utilize RTSP authentication, the user must first set a password for the camera. RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default the port number is set to 554. Authentication - Depending on the network security requirements, the camera provides two types of security settings for streaming via RTSP protocol: NONE and DIGEST.
Save File Folder. (This function only for firmware V3.1.0.x only) Recording folder path - The destination for saving the recording video files. Click Browse to specify the saving path. Snapshot folder path - The destination for saving the snapshot files. Click Browse to specify the saving path and select the format from the drop-down menu. Advanced Settings(This function only for firmware V3.1.0.
Sequence Parameter Set (SPS) & Picture Parameter Set (PPS)Enable or disable SPS and PPS in the H.264 packet. Sequence parameter sets (SPS), which apply to a series of consecutive coded video pictures called a coded video sequence, and Picture parameter sets (PPS), which apply to the decoding of one or more individual pictures within a coded video sequence. Click Apply to apply settings or Cancel to cancel changes.
Advanced Settings Camera MIC - The Network Camera supports two-way audio communication so that operators can transmit and receive audio simultaneously. By using the Network Camera's built-in microphone and an external speaker, users can communicate with people who are within range of the Network Camera. Camera Speaker – If the speaker is enabled, select the volume from the drop-down menu. Echo Cancellation Enabled - Enable to avoid an echo. Click Apply to apply settings or Cancel to cancel changes.
Multicast Multicast sends a video stream to the multicast group address and allows multiple clients to acquire the stream at the same time by requesting a copy from the multicast group address. Therefore, multicast can effectively save Internet bandwidth. The RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. Click “Enable” to enable Multicast stream 1 or Multicast stream 2. The default value for multicast address and port are 234.1.2.3 and 10000.
Privacy Mask Control – Enable the Privacy Mask control to mask the whole view. (This function only for firmware V3.1.0.x only) Privacy Mask Control (This function only for firmware V3.2.0.x or higher version) – Enable the Privacy Mask control to mask the certain area of the view, and up to three areas can be chosen. Hardware Privacy Mask Button(CB-Series Professional only) – Click to enable the privacy mask button on the camera. the user will not be able to use the privacy mask button.
Advanced Settings Hardware Privacy Mask Button ( CB-Series Professional only* ) – Click to enable that the HW button can enable/disable the feature of privacy masking. If it is not enabled, the user can’t use the HW button to enable/disable the feature of privacy masking. Click Apply to apply settings or Cancel to cancel changes.
Camera Control(*) Preset Point A preset position is a pre-defined camera view that can be used to quickly move the camera view to a specific location. To create a preset position: a. Use the Pan, Tilt and Zoom (PTZ) controls to steer the camera view to the wanted position. b. Enter a descriptive name under Current Position and click Add. c. The camera position and focus settings will be saved as a preset position. NOTE – A total of sixteen preset points can be set. d.
NOTE - The name of the preset point set as Home will have (H) added; for example, Gate (H). e. The camera can be configured to return to the Home position when the camera has been inactive for a specified length of time. Select the desired length of time from the drop-down menu and click Apply. Setting the time to zero prevents the camera from automatically returning to the Home position.
Privacy Mask Add / Edit Privacy mask A privacy mask can be created to conceal areas within the camera’s view. The Privacy Mask List displays all the masks that are currently configured for the network camera and if they are enabled. NOTE – A total of sixteen privacy masks can be created. To create a new privacy mask: a. Use the Pan, Tilt and Zoom (PTZ) controls or select Preset Point from the drop-down menu to steer the camera view to the wanted position. b. Click on Add.
Patrol Settings The camera can be set to patrol a group of preset points. For each patrol group, the user can configure the preset point order, movement speed, and viewing duration. To create a patrol group: a. Click on Add and enter a descriptive name in Description. b. Add preset points to the patrol group by clicking the c. Use the arrow buttons to change the order of the preset positions by using the Adjust the next to the desired preset point.
Network Network Settings This section explains how to configure a wired network connection for the camera. There are several ways to setup the camera over the Internet: (1) obtain an available dynamic IP address assigned by a DHCP server, (2) use a static IP, or use PPPoE (Point-to-point over Ethernet). Select the desire setup mode from the IP settings drop-down menu. 1.
3. PPPoE (Point-to-point over Ethernet): Use this mode if connecting to the Internet through a DSL Line. NOTE - To utilize this feature, it requires an account provided by an Internet Service Provider. Enter the user name and password provided by the ISP. Click Apply to apply settings or Cancel to cancel changes. IEEE 802.1X IEEE 802.1X is an IEEE standard for port-based Network Access Control. It provides an authentication mechanism to devices wishing to attach to a LAN or WLAN.
b. Enter your ID and password. c. Upload the CA certificate for your 802.1X configuration. Click Apply to apply settings or Cancel to cancel changes. UPnP Universal Plug and Play (UPnP) simplifies the process of adding a camera to a local area network. Once connected to a LAN, the camera will automatically appear on the intranet. Click “Enable” to enable this function and enter an UPnP name which the camera will appear under on the intranet. Click Apply to apply settings or Cancel to cancel changes.
DynDNS – Enable the DynDNS to allow the camera to have a fixed host and domain name. Refer to the DynDNS website (www.dyndns.com) to apply for a dynamic domain account. When an account has been created, enter the username, password and hostname. Click Apply to apply settings or Cancel to cancel changes. TZO TZO is a DDNS provider which allows users to create a dynamic DNS. Refer to the TZO website (http://www.tzo.com/) to apply for a dynamic domain account.
password and domain name. Click Apply to apply settings or Cancel to cancel changes.
EasyLinkTM EasyLinkTM is a unique Brickcom function which allows users to assign a unique name to the network camera. There is no need to configure the router to open up ports or remember hard-to-memorize IP address. When this function is enabled, users can use [uniqueEasyLinkname].mybrickcom.com to access the camera’s web GUI and live view. 1. Check the box to enable EasyLinkTM. 2. If Auto mode is selected, the following page will be displayed. NOTE - This mode is recommended. 3.
4. If Manual mode is selected, the following page will be displayed. a. Manually enter the Public IP Address, HTTP port and RTSP port or leave the default values. Click Apply to apply settings or Cancel to cancel changes. NOTE - The EasyLink function will not work if the following conditions occur: 1. The camera cannot be located behind a double NAT network. 2. The camera’s IP address cannot be assigned to specific port numbers using the router’s port forwarding. 3.
3G(*) Use this option if using a 3G SIM card to transmit video/audio surveillance over a 3G network a. Enter the APN (Access Point Number), Dial Number, PIN Code, User Name and Password provided by the ISP. b. Click Apply to apply the settings. The message below will be displayed if the 3G settings were successfully applied. c. Before disconnected the wired connection with the network camera, obtain the IP Address by opening EasyConfig.
d.The network camera can now be accessed over a 3G network. To access the video feed through the internet, open a web browser and enter the network camera’s IP address. A dialog window will pop up requesting a username and password. As stated on the previous page, the default username and password for the Administrator account are “admin/admin”.
These settings control how a Network Camera interacts with a wireless network. Users can identify the wireless network and enable wireless encryption. NOTE – This function is only available for Wireless models. Basic Settings Network Name (SSID) - The Service Set Identifier (SSID) is the network name used to identify the wireless signal. It is case-sensitive and can be up to 32 characters long. Wireless devices have a default SSID set by the factory.
Security - Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA-Personal/WPA2-personal) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication. A network encrypted with WPA-Personal/WPA2-personal is more secure than a network encrypted with WEP because WPA-Personal/WPA2-personal uses dynamic key encryption.
WEP- Wired Equivalent Privacy (WEP) is a basic encryption method which transmits network broadcast messages using radio signals. It is not as secure as WPA. Tx Key - Select a key from the drop-down menu. WEP Encryption - Select a level of WEP encryption: 64 bits 10 hex digits or 128 bits 26 hex digits. The default is 64 bits 10 hex digits. Key 1-4 - Enter the WEP key(s) manually. Authentication - The default is set to Open System, which allows either Shared Key or Auto authentication to be used.
WPA-Personal - WiFi Protected Access (WPA)-Personal Encryption - Supports two encryption methods with dynamic encryption keys: Temporal Key Integrity Protocol (TKIP) and Advanced Encryption Standard (AES). Select the algorithm type from the drop down menu: TKIP or AES. The default is TKIP. Shared Key - Enter the key shared between the Router and the server keys. Enter a password of 8-63 characters. Click Apply to apply settings or Cancel to cancel changes.
WPA2-Persona l - WiFi Protected Access (WPA2-Personal) Encryption - WPA2 supports AES encryption method with dynamic encryption keys. Shared Key - Enter the key shared between the Router and the server keys. Enter a password of 8-63 characters. NOTE - If using WPA or WPA2, each device in the wireless network must use the same WPA or WPA2 method and shared key or else the network will not function properly.
Advanced Settings Network Mode - From the drop-down menu, select the wireless standards running on the network. If there are Wireless-B, Wireless-G and Wireless-N (2.4GHz) devices on the network, use the default setting, BGN-Mixed. If there are Wireless-B and Wireless-G devices on the network, select BG-Mixed. If there is only Wireless-B devices on the network, select Wireless-B Only. If there is only Wireless-G devices on the network, select Wireless-G Only. If there is only Wireless-N (2.
Wi-Fi Protected Setup Use this method if the client device has a Wi-Fi Protected Setup PIN number. 1. Enter the network name from the device in the field. 2. Click to start WPS. 3. Click “Enable” to enable the WPS Button. If this feature is not enabled, the user will not be able to use the WPS button Click Apply to apply settings or Cancel to cancel changes.
allow streaming data through. HTTPS - (Hypertext Transfer Protocol over SSL) - This protocol allows authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect streaming data transmission over the Internet on a higher security level than HTTP. Click “Enable” to enable and Apply to apply settings or Cancel to cancel changes. . To enable HTTPS, users have to create and install a certificate. 1. Click “Continue to this website” to install. 2.
4. Click “Install Certificate” and follow the steps to finish the installation.
Event Event Settings When an event (such as something moving) occurs, the camera can be scheduled to perform certain actions. This section describes how to configure the camera to perform certain actions when events occur. Click on the Event Settings page. The Event Setup page will appear.
How to Set Up an Event Schedule Event Schedule describes how and when the camera performs certain actions. 1. Check “Enable” and enter a descriptive name for the event schedule. 2. Set Event Schedule to define when the event is activated by selecting from Always (24 hours), Schedule or Recurrence pattern. a.
i. A Scheduled Event can be programmed for certain times and day. ii. Click individual boxes to schedule specific times for the camera to detect events. b. If Recurrence Pattern is selected, the following page will be displayed.
i. An event schedule can be programmed to recur at different times according to the user’s needs. Select the days for the event schedule to occur. Select a start time and specify the duration. 3. Define what will trigger an event to occur by selecting an option from the Event drop-down list. 4. Select the Actions that will occur when the event is triggered.
a. When is selected, the following page will be shown: ii. Sender - Enter the email address of the sender. iii. Recipient - Enter the email address of the recipient. To enter multiple recipients, separate each using a comma. iv. Sender’s Name – Enter the sender’s name that will appear in the recipient’s inbox. v. Subject - Enter the title of the email. 5. When complete, click Apply to save new event or Cancel to delete the event. The new event will appear on the event list. 6.
NOTE - Refer to the Audio Clip section for more details about the “Play Audio Clip” action. Motion Detection Motion can be detected by measuring changes in the speed or vector of an object or objects in the monitored area. This section explains how to configure the Network Camera to enable motion detection. Detection Setting – Use this setting to enable and define the motion detection windows. The user can defined up to three areas on the live view window for motion detection. 1.
to trigger an event. 5. Adjust the “Threshold” to change the threshold level. The higher the threshold, the larger objects need to be to trigger an event. 6. The chart below the Live View window indicates the activity level of the Motion Detection window. When motion is detected by the camera and exceeds the defined threshold, a red bar will appear. Users can use this feature as a trigger source to send photos or videos to a remote server via email or FTP.
2. Edit Mode For setting Video Analytics, click ‘Edit mode’ to do further set-up. Video Source - You can choose the certain stream as the video source for the video analytics. Just choose it from the drop-down menu.
Cordon Information - Click “Enable”, then the cordon will take effect. If it is not enabled, the cordon just be kept as a setting, and will not take effect. Click Apply to apply settings or Cancel to cancel changes. The screen at the right side will be disabled when you are working to draw the cordon: Draw lines as the virtual fence to detect if there is an invader across the cordon.
Set a border (as the hot zone) for the function of the left/missing object. The system shall alarm, if there is something to be left into there or be moved out. Head Circumference The people count function focuses on the tracking of circular object, so here is to set the values of the head circumference. . Click the above icons to draw two circles as the way to specify the head circumference.
Advanced Settings Common Parameter Trigger Point: caused by the different view angle, the trigger point should be adjusted for the actual environment. For the most cases, select “Center mode” for the vertical shot, or select “Bottom mode” for the horizontal shot. Mini sampling frame: The minimal frames to recognize a moving object. The smaller causes to be more sensible/sensitive. Min pixels per object: The Min. pixels are for an object. The smaller causes to recognize one object to become two separate.
On Screen Display Cordon Enable: To control if the cordon is shown inside the image as the part of the video. Moving Object Enable: To control if the highlight of the moving object is shown inside the image as the part of the video. Trajectory Enable: To control if the trajectory is shown inside the image as the part of the video. Counting Enable: While an invader cross over the line, then the camera counts it automatically. So enable this one to let the count numbers be shown as the part of the video.
Abandon End: After the system alarms for the lost object, the system shall start to save a picture as the next comparison target. To continue the previous example, if the chosen stream is configured as 15 fps, and this parameter is 300, then 20 seconds after the system alarms for the lost object, the system shall save a picture as the next comparison target. Digital Input (DI) The DI socket allows the IP camera to receive input from an external device.
sensor will be able to detect moving objects within six meters. Audio Detection Users can schedule an event to be triggered if there is a change in the sound level of a monitored area. Audio detection can be used to measure change in the ambient voice. Select the sensitivity from the drop-down menu. Sensitivity - is used to adjust the sensitivity of the sound level from 10 - 100%. The default sensitivity is 50%. Display the current sound level. Click Apply to apply settings or Cancel to cancel changes.
Notifications Use the tools in this section to specify what type of notification will be sent when an event occurs. The camera can send buffered images to an FTP server, Samba, Email, or HTTP. FTP Settings File Transfer Protocol (FTP) is used as an application component to automatically transfer files for program internal functions. Select “Primary FTP Server” from the Server Selection drop down menu to send media files to a FTP server when an event is triggered. Enter the FTP IP address or hostname.
E-mail Settings Select “Primary Email Server” option from the Server Selection drop down menu to send media files to an email server when an event is triggered. SMTP Server - Enter the server host name of the email server. SMTP Port - Enter the port number of the email server; by default, the SMTP port is set to 25. Authentication - Select the authentication type from the drop-down menu. Email Account - Enter the user name of the email account if necessary.
Samba Settings Select this option to send the media files via a network neighborhood when an event is triggered. Server Address - Enter the IP address of the Samba server. User Name - Enter the user name of the Samba server. Password - Enter the password of the Samba server. Work Group - Enter the workgroup of the Samba server. Shared Folder - Enter the share folder of the Samba server. Click Apply to apply settings or Cancel to cancel changes.
Parameter – type the notification parameter if necessary. Example URL - http://192.168.1.1/xxxx.cgi Message - name1=value1&name2=vlaue2 Result - http://192.168.1.1/xxxx.cgi? name1=value1&name2=vlaue2 Ex: https://192.168.1.1/notification.cgi?event=MD&camera=FB-100A Message - Enter the message notification that will be sent when an event is triggered. Enter the user name and password if necessary. Click Apply to apply settings or Cancel to cancel changes.
Video Clip/Snapshot Video Clip If there is an event happened, the camera can be configured to record the video as a reaction. Pre-alarm buffer - Images can be stored internally from the time immediately preceding the trigger. Enter the desired length of time. Post-alarm buffer - Images can be stored internally from the time immediately following the trigger. Enter the desired length of time. Maximum buffer size – To specify the Max. file size of each video clip.
Audio Clip(*) Audio Recording – Audio clips can be recorded and played when an event occurs. Click Browse to import a file from a local hard drive or network disk. Import. Select the file and click NOTE – The camera can only play audio clips which are saved as .wav files with G.711 u-law encoding in 8000 Hz sampling rate. To record a new clip using the camera's microphone: 1. File Name-Enter a file name. 2. Duration - Enter the number of seconds to record. 3. Click Record to record the new audio clip.
LED Light (*) Mode – Select “Keep active during event” or “Keep active for” a specific amount of time when an event is triggered. LED Control - The LED on the front of the camera can be set to flash at a configurable interval when an event is triggered. From the Activate drop down menu, select a percentage which the LED will brighten to. When the LED reaches the selected percentage, it can be configure to fade to off or turn off. Select the option from the Inactive menu.
System System Log Log – Set up the camera to record a system log when an event is triggered. This page displays the system’s log in chronological order. The system log is stored in the camera’s buffer area and will be overwritten when the buffer area is full. Click Retrieve to retrieve the log or click Save to file to save the system log.
Remote Logging The user can configure the camera to send the system log file to a remote server as a log backup. Click to enable remote log and enter the IP address of the remote server. Enter the port number of the remote server. Click Apply to apply settings or Cancel to cancel changes. Date and Time Time Zone – Select the local time zone from drop-down menu. Manual – Manually enter the date and time.
Click Apply to apply settings or Cancel to cancel changes. Device Information System Information – Displays the complete system information of the camera. Network Settings –Displays the complete network settings information of the camera.
Video/Audio Settings –Displays the complete video/audio settings information of the camera. Wireless(*) - Displays the complete wireless information of the camera. Client Information- Displays the RTSP Client. following information: IP Address and channel.
Storage Management (*) Storage Management is used to view all the recorded files on the Micro-SD/SDHC card. Click Reload to refresh the list of recorded files. Click Remove to safely remove the Micro-SD/SDHC memory card. Click Format to format the Micro-SD/SDHC memory card. Left click on the folder to list the recorded files. The user can either play the snapshot of the recorded files by moving the mouse pointer over the file or double click on a file to play it.
Advanced Settings Automatic Recycle (*) – Enable to automatically overwrite older files when the available space remaining on the Micro-SD/SDHC card is less than 100MB. If the Automatic Recycle function is disabled, there must be at least 50MB hard drive space available for the camera to be able to record video files. Offline Record – Enable to keep recording if the Network Camera is offline. FTP Service – Enable to Camera FTP Server.
openssl enc -ciphername [-in filename] [-out filename] [-pass arg] [-e] [-d] [-a/-base64] [-A] [-k password] [-kfile filename] [-K key] [-iv IV] [-S salt] [-salt] [-nosalt] [-z] [-md] [-p] [-P] [-bufsize number] [-nopad] [-debug] [-none] [-engine id] For example: openssl enc -d -aes128 -in encryptfile -out decryptfile -k password Click Apply to apply settings or Cancel to cancel changes. LED Indicators The LED on the front of the camera can be configured to remain unlit.
Click Apply to apply settings or Cancel to cancel changes.
Maintenance User Management This section explains how to enable password protection and create multiple accounts. The administrator account name is “admin”, which is permanent and cannot be deleted. Click Add to create an account. Enter the new user’s name, password and confirm password. Administrators can add up to 10 user accounts. Select the privilege level for the new user account from the drop-down list.
Administrator - user has access to view and change the Configuration page. Users with administrator privilege can change other user’s access rights and delete user accounts. Click Delete or Update to delete or modify a user’s account. Viewer - user can only access the main page for live viewing. Remote Viewer - user can only access the main page for live viewing using TCP protocol. Language Select the desired language from the radio button.
Click Apply to apply settings or Cancel to cancel changes. Firmware Upgrade This feature allows the user to upgrade the camera firmware. It will take a few minutes to complete the process. NOTE - Do not power off the camera or camera during the upgrade. Upgrade - Click Browse… and specify the firmware file. Click Upgrade. The camera will begin upgrading and will reboot automatically when the upgrade is finished. The following message will show during the firmware upgrading process.
Configuration This feature allows the user to export/import the configuration files of the network camera. Import/Export - Click export to pop up a dialog to indicate the location and file to export. Click browse to indicate the location and file of the camera configuration and click import to import the configuration file back into the network camera. Reset to Default This section is used to restore the camera to default factory settings.
device will reboot. Are you sure?” Click “OK” to continue. The camera will take about one minute to reboot. The following message will show during the rebooting process. When completed, the live video page will be displayed in the web browser.
