User Manual Model: C3236 Checkweigher AWT35-501815 Issue AA C3236_u_en_501815.
Table of Contents 1. General information and Warnings page 5 FCC Declaration of Compliance - Déclaration de conformité..……...…………..…... 5 Training - Formation……………………..………………………………...……………... 6 Battery Safe Disposal - Élimination sécurisée des batteries……...………………….. 6 Routine Maintenance - Entretien de routine……………………………………..…….. 6 Cleaning the Machine - Nettoyage de la machine………………………….…………. 6 Sharp Objects - Objets tranchants………………………….………………...……....... 6 2.
4. Menus page 12 User Menu……………………..……………………………………….………….………. 12 User Menu Levels………………….……………………….………………………… 12 User Functions Descriptions [UF].………………….……….……………………… 12 Supervisor Menu....………………………….……………..…………………..…………. 13 Supervisor Menu Levels……..……….……………………………………………… 13 Supervisor Functions Descriptions [LF].…………..….……………………….…… 14 Quick Calibration Menu……..………………………..……………………….…………. 15 Quick Calibration Menu Levels…...…………….
Manual revision history Current Issue Draft AWT35-501815 Issue AA Date Created Jan. 2019 C3236_u_en_501815.
1. General Information and Warnings 1.1. FCC Declarations of Compliance - FCC Déclaration de conformité United States This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
1.4. Training - Formation Do not attempt to operate or complete any procedure on a machine unless you have received the appropriate training or read the instruction books. Ne pas tenter d’utiliser la machine ou lui appliquer une quelconque procédure sans avoir reçu une formation adaptée ou lu les manuels d’instruction. CAUTION! Risk of electrical shock. Refer to qualified service personnel for service. ATTENTION! Risque de choc électrique. Confier la réparation de l’appareil à un personnel qualifié. 1.5.
2. Introduction The C3236 is a high resolution stainless steel IP68 wash-down scale ideal for general food weighing, portion control or checkweighing applications. This scale offers a fast weight indication along with an easy to use Under, Over and Acceptable weight indication. Ideal for most food processing environments or where weighing needs to take place in a clean wet environment. This manual covers the introduction to the unit, its use, configuration and calibration. 2.
When the scale is turned on, the battery annunciators are: - LOW BATTERY, battery needs to be recharged; - CHARGE, battery is being charged (6hrs). Do not use any other type of power adaptor than the one supplied with the scale and verify that the AC power socket outlet is properly protected. Charge the battery before using (+6hrs). Caution! When cleaning or washing down the scale, please insure the power adaptor is fully removed from the scale prior to cleaning. Figure 1 - C3236 underside view. 2.5.
2.5.2. Operation Keys Keys are shown below along with their functions. Some keys have secondary functions. - Press the UNITS key to scroll through the active units of measure. - In Menu mode: It aborts a numeric entry and acts as an ESCAPE key for menu navigation (ESC). Press and hold the OFF key to turn off the scale. oFF will be displayed for 2 seconds. - Press the ON key to turn on the scale. The scale will self-adjust to 0. Press this key to Zero the display.
3. Scale Operation The steps for various kinds of weighing are explained in the following pages. To set parameters and calibrate the unit, see chapters 4.3. Supervisor Menu on page 13 and 6. Calibration on page 17. A warm-up time of 15 minutes is required to stabilize the measured values. 3.1. Gross Weighing To perform a gross weighment, follow these steps: 1. Power up the scale. Be sure the scale is displaying weight in the correct unit of measure. Press the UNITS key, if necessary. 2.
3.3.1. Setting the Checkweighing Limits i. When the scale is ON, press FN (▲) key; UF-1 will be displayed. ii. Press FN (▲) key; UF-2 will be displayed. iii. Press ON/ZERO/TARE (↵) key; iv. To enter or edit the LO limit value, scroll through the displayed digits by using the ON/ZERO/TARE (↵) key. Press the FN (▲) key to increase the value of the flashing digit. v. Press ON/ZERO/TARE (↵) key to confirm; vi. Repeat points iv. and v. for the HI limit; vii.
4. Menus There are three menus that allow to configure, enable or execute specific functions or options. page 12 • User Menu UF – 1 ~ 11 13 • Supervisor Menu LF 1 ~ 8 15 • Quick Calibration Menu ECF – 1 ~ 3 4.1. User Menu In the User Menu there are various submenus available to configure specific sections of the scale operating modes, including a diagnostic feature. 4.1.1. User Menu Levels [UF] Navigate the menus and increase a numeric value by pressing FN (▲) key.
UF-3 Auto Power-Off: use this to set the length of time before the scale automatically turns off if not being used. Values can be set between 01 and 99 minutes. Factory default: AoFF 10 (10min). Auto Power-OFF disabled when AoFF 00 UF-4 Stand by: a battery power saving function to turn off the display power but not turn off the scale. Ideal for weight processes where the scale could say inactive for long periods of time and where the Zero point or current weight cannot be lost.
4.2.2. Supervisor Functions Descriptions [LF] There are 8 functions. st LF 1 1 Calibration: see chapter 6. Calibration on page 17 for a detailed procedure. LF 2 Configuration: use this item to configure system parameters, specific sections of the operating modes. See chapter 5. Scale Configuration at page 16. LF 3 Linearization: use this to add 1-3 linearization points for the scale equivalent to 0, 1/3, 2/3 and 3/3 of the max capacity.
4.3. Quick Calibration Menu See chapter 6. Calibration on page 17 for a detailed procedure. NOTE: Default calibration units are in kg. To change this to lb please refer to Scale configuration LF 2 on page 16. 4.3.1. Quick Calibration Menu Levels [ECF] Navigate the menus and increase a numeric value by pressing FN (▲) key. Use ON/ZERO/TARE (↵) key to confirm and/or move to the next option or numeric value position. Press UNIT (ESC) key to exit the option or the menu. 4.4.2.
5. Scale Configuration [LF 2] Enter the function LF 2 to set the units, range mode, calibration units, decimal position of the separator and division size. Navigate the menus and increase a numeric value by pressing FN (▲) key. Use ON/ZERO/TARE (↵) key to confirm and/or move to the next option or numeric value position. Press UNIT (ESC) key to exit the option or the menu. AWT35-501815 Issue AA C3236_u_en_501815.
6. Calibration It is recommended to perform only the very first calibration following the function LF 1 in the Supervisor Menu. To prevent any unintentional change of the scale configuration, all the subsequent Calibrations should be performed entering the Quick Calibration Menu [ECF]. Both procedures above, must be conducted following the steps on the 6.1 Scale Calibration Procedure. 6.1.
7. Replacement Parts Part number Description AWT25-502472 Power supply universal with USA-UK & EU plug adaptors (100 to 240VAC 50/60 Hz output: 12V 1000mA with special water proof 2 pin connector) Replacement battery (DJW6-4.0 6V4.0AH lead acid battery) AWT20-509288 AWT35-501815 Issue AA Replacement feet Kit (4 feet and lock nuts) C3236_u_en_501815.
AWT35-501815 Issue AA C3236_u_en_501815.
