Assembly & Installation Instrutions
Page 2/4
Installation steps
1. Thread two headless screws through the cross bar, and then secure them with four lock nuts (two on each side of
the cross bar). Adjust the length of the headless screws if necessary.
Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
2. Attach cross bar to outlet box using two mounting screws.
3. Gently slide the glass panel into the metal frame in place. With one side locating into the
slot of “L” clip, secure the other side of the glass panel by pressing the clips.
(See Fig.1 & Fig.2)
4. Pull out the source wires from the outlet box. Make wire connections using wire
connectors as follows:
---Connect the hot wire (usually black insulation) from the fixture to the black wire from
the power source.
---Connect the neutral wire (usually white insulation) from the fixture to the white wire
from the power source.
---Attach the fixture grounding wire (usually green insulation or bare wire) to the cross
bar with the green grounding screw, and then connect it to the house grounding wire
with the wire connector.
Carefully put all of the wires back into the outlet box.
5. Attach the fixture to the cross bar by inserting headless screws into holes on back plate, and then secure it with two
rubber pads and two ball nuts.
CAUTION:With silicone caulking compound, caulk completely around where the back plate meets with the
wall surface to prevent water from seeping into the outlet box.
6. Install a bulb (not included). Check relamping label at socket area or packaging for maximum allowed wattage.
Turn off the power at fuse or circuit box.
Turn on the power at fuse or circuit box.
Function and Operation
MODES OF OPERATION
Choose a mode by sliding the switch on the back of the sensor. when power is first applied, the light will turn on
immediately. Wait for 100 seconds to allow the sensor to warm up.
“L” Clip
Clip
Glass
Panel
Metal
Frame
Fig. 1
Fig. 2
1. TEST MODE (daytime and nighttime operation)
● The light will turn to low-level brightness (0%~50% brightness). The light will turn to high-level brightness (100%
brightness) when motion is detected, and stay on as long as the motion is continuing. The light will revert to
low-level brightness about 5 seconds after motion is no longer detected.
2. 3H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 3 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set.
● Light will turn off automatically at dawn, and return to 3 H mode at dusk.
3. 6H MODE (nighttime operation only)
● At dusk, the light will turn to high-level brightness (100% brightness). The light will turn to low-level brightness (0%
~50% brightness) automatically after 6 hours. The light will turn to high-level brightness (100% brightness) when
motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light
will remain on for the predetermined time you set (5~180 seconds), and then revert to low-level brightness you set
● Light will turn off automatically at dawn, and return to 6 H mode at dusk.
4. 0 MODE (nighttime operation only)
● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness
(100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no
longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to
low level brightness you set.
● Light will turn off automatically at dawn, and return to 0 H mode at dusk.