Owner Manual

MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
meet all UL specifications.
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between
the fixture and the mounting surface by using silicone or similar caulking.
1.
Turn off power at circuit box to avoid possible electric shock.
2. Secure mounting bar (A) to outlet box (B) with outlet box screws (C) ( if applicable ) (see fig. 1).
3. Thread hex nut 1 (D1) onto mounting nipple (E) approximately 1/4 inch and insert lock washer 1 (F1),
then thread mounting nipple (E) onto mounting bar (A) and secure with hex nut 1 (D1).
4. Secure fixture loop (G) to nipple (H).
5. Open the chain (J) to connect to one link on bottom end of chain (J). Attach to fixture loop (G).
Securely close link on chain.
6. Thread screw collar ring (N) onto screw collar (O), then place canopy (P) over top of screw collar (O).
7. Lace wires up through every other link on chain (J) then through canopy (P).
8. Open the chain (J) on top end of chain (J) to connect to the screw collar (O). Attach to fixture screw
collar (O). Securely close link on chain.
9. Identify color coding of fixture wires (see fig. 2).
10. Connect the smooth wire with marking printed or molded from the fixture with the black wire from
outlet box (B) by wire connector (Q), and wrap the wire connector (Q) with electrical tape for a
more secure connection.
11. Connect the ribbed wire from the fixture with the white wire from the outlet box (B) by wire
connector (Q), and wrap the wire connector (Q) with electrical tape for a more secure connection.
12. Partially thread green grounding screw (R) into side hole (S) on mounting bar (A).
13. Wrap grounding wire from fixture around green grounding screw (R) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (B) by wire connector (Q) (if applicable), then wrap the wire connector (Q) with electrical tape
for a more secure connection.
14. Tighten green grounding screw (R). Do not over tighten.
15. Remove screw collar ring (N) from screw collar (O) and secure screw collar (O) to mounting nipple (E).
16. Tuck wires inside outlet box (B).
17. Raise canopy (P) to ceiling and secure screw collar ring (N) to screw collar (O).
18. Install lamp(s). Do not exceed recommended wattage.
19. Turn on power at circuit box.
WARNING
Turn off electricity to the mounting site before beginning installation.
Mounting instructions must be followed exactly as shown for the fixture to be safely sup-
ported.
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic lac-
quer which gives maximum protection against the weather. However, in time the brightness of the
brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass fixture
looking new for years to come, regularly apply a good quality, non-abrasive car wax to all metal sur-
faces, giving the fixture an extra protective covering.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
FIGURE 2.
FIXTURE
WIRES:
Smooth
HOUSE
WIRES:
Black
(Hot)
HOUSE
WIRES:
White
(Neutral)
HOUSE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Bare
Copper
(Ground)
FIXTURE
WIRES:
Ribbed
WARRANTY INFORMATION
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHTING FIXTURE
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any
packing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is
essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not
damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components
are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are
provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before
1985 have supply wires rated 60° C. Consult a qualified electrician before installing.
Owner’s Manual
Outdoor Lighting Fixture
Installation Instructions
Guide d’utilisation
Instructions d’installation
Appareil d’éclairage pour utilisation extérieure
GARANTIE LIMITÉE DE CINQ ANS
MISE EN GARDE: L’ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l’installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de
commencer l’installation. Un câblage approprié est essentiel au bon fonctionnement de cet
appareil d’éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur
ou un plafond, n’endommagez pas les câbles électriques, les canalisations de gaz ou d’eau. Si
l’un des composants de raccordement ou de l’appareil d’éclairage est endommagé, n’installez
pas cet appareil d’éclairage. Retournez-le à l’endroit où vous l’avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l’appareil
d’éclairage est doté d’un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l’étiquette U.L. et sur l’emballage de l’appareil d’éclairage.)
LES INSTRUCTIONS D’ASSEMBLAGE DE L’APPAREIL D’ÉCLAIRAGE POUR UTILISATION EXTÉRIEURE
NOTA : Déballez soigneusement l’appareil d’éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l’emballage au rebut (voir fig. 1).
*GROUND
WIRE
SIDE
HOLE (S)
WIRE
CONNECTORS (Q)
OUTLET BOX
SCREWS (C)
SCREW COLLAR (O)
LOCK WASHER 1 (F1)
HEX NUT 1 (D1)
MOUNTING NIPPLE (E)
CANOPY (P)
CHAIN (J)
SCREW COLLAR RING (N)
FIXTURE LOOP (G)
NIPPLE (H)
MOUNTING
BAR (A)
*OUTLET
BOX (B)
GREENGROUNDING
SCREW (R)
*NOT SUPPLIED
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
FIGURE 1.
*FIL DE MISE
A LA TERRE
TROU
LATERAL (S)
CONNECTEURS
DE FIL (Q)
VIS DE LA BOITE DE
SORTIE DE COURANT (C)
COLLIER FILETE (O)
RONDELLE DE BLOCAGE 1 (F1)
L’ECROU HEXAGONAL 1 (D1)
MANCHON FILET
DE FIXATION (E)
CHAPEAU (P)
CHAINE (J)
LA BAGUE DU COLLIER FILETE (N)
LA BOUCLE DE
L’APPAREIL
D’ECLAIRAGE (G)
MANCHON FILETE (H)
BARRE DE
FIXATION (A)
*BOITE DE SORTIE
DE COURANT (B)
VIS DE MISE A LA
TERRE (VERTE) (R)
FIGURE 1.
*NON FOURNI
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l’appareil
d’éclairage contenu dans la boîte.
Les instructions d’installation demeurent
cependant valables.
All rights reserved. Made in China