Installation & Assembly

CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
Note: Portions of installation will require (2) people.
1) Passxturewirethroughlongthreadedpipe[1](with2hexnuts
onit).
2) Screwthepipeintothehexcoupling[2]allthewaydownuntil
thehexnuttouchesthecoupling.
3) Passthexturewirethroughthewideopeningofthetopcov-
er[3].Restthecoverontothetophousing[4].(Somethreads
shouldbeexposedfromthetop.Youcanadjustthehexnutsto
seatproperly).
4) Passthexturewirethroughthesmallcoupling[5].Screwthe
couplingontotheexposedthreadsfromthetopofthecover.
Tightentosecure.
5) Passxturewirethroughdesiredamountofstems[6]and
screwstemstogetherusingsuppliedshortthreadedtubes[7].
 NOTE:Threadlockingcompoundmustbeappliedtoallstem
threadsasnotedwitharrowsymboltopreventaccidentalrota-
tionofxtureduringcleaning,relamping,etc.
6) Passxturewirethroughendofswivel[8]withoutthreaded
pipe.Threadthatendofswivelontoendoflaststem.
 NOTE:Directionofswivelinaccordancewithceiling.
7) Passxturewirethroughholeincanopy[9].Passthreaded
pipeonendofswivelupthroughholeincanopy.
8) Passxturewirethroughlockwasher[10].Threadlockwasher
 ontoendofthreadedpipeprotrudingfrominsidecanopy.
9) Passxturewirethroughhexnut[11].Threadhexnutontoend
ofthreadedpipe.
10) Findtheappropriatethreadedholesonmountingstrap[12].
Assemblemountingscrews[13]intothreadedholes.
11)Attachmountingstraptooutletbox[14].Mountingstrapcan
beadjustedtosuitpositionofxture.
12)Groundinginstructions:(SeeIllus.AorB).
 A) Onxtureswheremountingstrapisprovidedwithahole
andtworaiseddimples.Wrapgroundwirefromoutletbox
aroundgreengroundscrew,andthreadintohole.
 B) Onxtureswhereacuppedwasherisprovided.Attach
 groundwirefromoutletboxundercuppedwasherand
 greengroundscrew,andthreadintomountingstrap.
 Ifxtureisprovidedwithgroundwire.Connectxtureground
wiretooutletboxgroundwirewithwireconnector.(Notpro-
vided.)Afterfollowingtheabovesteps.Neverconnectground
wiretoblackorwhitepowersupplywires.
13)Makewireconnections(connectorsnotprovided.)Reference
chartbelowforcorrectconnectionsandwireaccordingly.
14)Pushxturetoceiling,carefullypassingmountingscrews
throughholesincanopy.NOTE:Becertainwiresdonotget
pinchedbetweencanopyandceiling.
15)Useknobs[15]andlockwashers[16]tosecurecanopy.Tighten
tosecure.
16) Insertrecommendedbulb.(Notsupplied)
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
►
►
►
►
1
2
3
4
5
6
7
8
9
10
11
13
12
14
15
16
17
18
19
20
21
22
23
17) Carefullylowertheglass[17]ontothelowertrim.
18) Using(2)people,raisethelowertrim/glassuptothetophous-
ing.Slipthetophousingarms[18]insidetheslotofthelower
trimsupportarms[19].Aligntheholesofthetophousingarms
withtheholesinthelowertrimarms.
19) Slideasupportarmscrew[20]throughtheholeinanarm.
Screwanial[21]ontothescrew.Repeatthisstepforremain-
ingarms.
20) Tightentosecurethetrimtothearms.