Installation & Assembly

IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Shut o
the power at the circuit breaker and completely remove the old xture from the ceiling,
including the old mounting strap.
From the parts bag remove the mounting strap assembly. One end of nipple (F) should
be attached to mounting strap (A) with washer (C) and hex nut (D) in place. The other
end should have canopy loop (H) attached. Attach mounting strap (A) to the junction
box using mounting screws (B) and a screwdriver. Tighten securely. Unscrew canopy loop
collar (I) from canopy loop (H). Pass canopy (G) over the mounted canopy loop to test the
height. Approximately half of the canopy loop’s exterior threads should be exposed, and
the canopy loop collar should t snugly onto the canopy loop. Remove canopy (G) and
adjust the height of nipple (F) and canopy loop (H) until the desired height is reached.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn o the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling. Slide canopy loop (H) and canopy loop collar (I) up beneath the canopy. Tightly thread canopy loop collar (I) onto
canopy loop (H) to secure canopy (G) in place.
Install light bulbs (not provided) in accordance with the xture’s specications. Do not exceed the maximum recommended wattage. Position
the arms. If the decorative twists (R) are loose, use the small tool (Q) to tighten.
Your installation is complete. Turn on the power and test the xture.
ASSEMBLING THE FIXTURE
Gently place lamp body (T) on a at surface. Thread spacer (Q) onto post (U) of lamp
body (T). Push the xture’s wires through rod (P). Position rings (O) to create an opening
large enough to place lamp body (T) inside. Carefully pull the xture’s wires through the
nipples (U and (W) before threading rod (P) into nipple (W). Pull the wires until taut and
gently rotate post (U) of lamp body (T) onto the bottom of rod (P) until lamp body (T) is
securely locked onto rod (P).
Place washer (M) onto nipple (N) and twist top loop (L) onto the threads. By measuring,
determine the correct number of chain links needed for proper hanging height. If
necessary, use a pair of pliers to open and remove any excess chain. Attach chain
connectors (K) to each end of chain (J) before attaching one end of the chain connector/
chain to top loop (L). Close the chain connector. Connect the other chain connector (K)
to canopy loop (H). Feed the xture’s wires up through top loop (L) then through chain
(J) (every three links or so). Pull the wires until taut. Gently slide canopy loop collar (I) and
canopy (G) onto the chain/wires.
CONNECTING THE WIRES
Have an assistant support the xture’s weight while completing the wiring. Cut away excess
wire. Attach the xture’s wires to the power supply wires from the junction box. Connect black to
smooth/black/transparent (L) wire; white to ribbed/white/transparent (N) wire; ground to ground
(green or copper). Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no ground wire (green or copper) from
the junction box, locate ground screw (E) on mounting strap (A) and wrap the xture’s ground
wire around the green ground screw (E). Use a screwdriver to secure ground screw (E) onto the
mounting bracket/mounting strap. Tuck all wires.
A
C
D
E
F
G
H
I
J
B
L
M
K
N
O
O
O
P
R
S
Q
T
U
W
Assembly Instructions