Assembly Instruction

ManualsBrandsBrayden Studio ManualsCeiling LightsVoegele 5-Light Shaded Geometric Chandelier

2of3

(Step 4A Continued)

Assembly (AA) by unscrewing the preassembled hex nut and lock

washer and then screwing the mounting screws in or out of the

crossbar until the correct length is achieved. Once the Ceiling

Canopy (A) is secure, remove the mounting ball and Ceiling Canopy

(A) and proceed to Step 5A.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 4A

STEP 5A - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

White wire

from supply

White wire

from fixture

Black wire from

supply (or Red)

Black wire

from fixture

Ground wire

from supply

Ground wire

from fixture

Figure 5A

STEP 6A - Install the Fixture Body

A. Position the Ceiling Canopy (A) and Fixture Body onto the Crossbar

Assembly (AA). Place the holes in the Ceiling Canopy (A) over the

mounting screws. Secure the Fixture Body by using the mounting

balls and hand tighten the mounting balls until snug.

Mounting Ball

Mounting

Screw

Figure 6A

STEP 7A Install Glass Panels and Bulbs-

A. Remove Lock Screws from Socket Assembly (I). Attach Glass

Panels (J) to Socket Assembly (I) with wider edge is on the top.

Secure by threading Lock Screws back into Socket Assembly (I). Do

not release your hands with Glass Panels (J) until hand tighten Lock

Screws until snug.

B. Insert bulbs onto sockets and screw snugly into place.

Your fixture is now assembled and ready to use.

Enjoy!

Figure 7A

Assembly Instructions for Semi-flush Light

(Step 1B - Step 6B)

Part B, Part C and Part H will not be used in the assembly of the

Semi-Flush Light fixture. Please set aside these parts.

6” Rod

12” Rod

Extra Parts include

Swivel

Optional

Swivel

STEP 1B Install Ceiling Canopy to Socket Assembly-

A. Pass supply wires with ground wire through Nipple (D), Ceiling

Canopy (A), Flat Washer (G), Lock Washer (F) and Hex Nut (E).

Thread Nipple (D) onto Socket Assembly (I). Place Ceiling Canopy

(A), Flat Washer (G) and Lock Washer (F) onto Nipple (D). Secure

by threading Hex Nut (E) onto Nipple (D). Hand tighten until snug.

Cut the wires leaving approximately 6” of wire extending from the

Figure 1B

Supply Wires and

Ground Wire

Ceiling Canopy.

B. Optional Swivel: Install the

swivel to Socket Assembly (I)

and then attach Nipple (D)

and Ceiling Canopy (A) to the

Swivel using The Flat Washer

(G), Lock Washer (F) and Hex

Nut(E)asinstepA.

STEP 2B - Installing the Crossbar

Assembly

A. Pass the supply wires through the

Crossbar Assembly (AA). Attach

the Crossbar Assembly (AA) to the

Outlet Box with the head of the

Green Ground Screw facing you.

Secure the Crossbar Assembly (AA)

with Outlet Box Screws (not

included). Tighten until snug.

Figure 2B

Supply

Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet

Box

STEP 3B - Test Fit the Ceiling Canopy to the Crossbar Assembly

A. Remove the mounting balls from the Crossbar Assembly (AA).

Place the Ceiling Canopy (A) onto the Crossbar Assembly (AA) and

secure with mounting balls. Note: The Ceiling Canopy (A) should be

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3B

snug against the

ceiling and held

tight with the

mounting balls. If it

is not, adjust the

length of the

mounting screw on

the Crossbar

Assembly (AA) by

unscrewing the

preassembled hex

Lock Screw

Bulb (not

supplied)

Socket