Assembly Instruction

ManualsBrandsBrayden Studio ManualsCeiling LightsVoegele 5-Light Shaded Geometric Chandelier

1of3

(5)A19MediumBaseBulbs100WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Assembly Instructions for Pendant Light

(Step 1A - Step 7A)

Hardware Contents

Package Contents

Crossbar Assembly

6” Rod

Ceiling Canopy

12” Rod

Socket Assembly

Nipple

STEP 1A Attach Swivel and Ceiling

Canopy together

A. Thread Nipple (D) onto the Swivel

(H).

B. Place Ceiling Canopy (A), Flat

Washer (G) and Lock Washer (F) over

the Nipple (D). Secure by threading

Hex Nut (E) onto the Nipple (D),

tighten until sung with screwdrivers.

Figure 1A

STEP 2A Assemble Rods and the Ceiling Canopy-

A. Determine Rods (B/C) to be assembled to Socket Assembly (I)

according to your hanging height.

C. Pass supply wires and ground wire through the chosen rods (B/C)

and Ceiling Canopy (A). Thread Socket Assembly (I), the chosen

Rods (B/C) and the Swivel (H) together.

Hand tighten until snug.

Suggested rods for Ceiling height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and (2) 12” rods

STEP 3A - Installing the Crossbar

Assembly

A. Pass the supply wires through the

Crossbar Assembly (AA). Attach

the Crossbar Assembly (AA) to the

Outlet Box with the head of the

Green Ground Screw facing you.

Secure the Crossbar Assembly (AA)

with Outlet Box Screws (not

included). Tighten until snug.

Figure 3A

STEP 4A - Test Fit the Ceiling Canopy to the Crossbar Assembly

A. Remove the mounting balls from the Crossbar Assembly (AA). Place

the Ceiling Canopy (A) onto the Crossbar Assembly (AA) and

secure with mounting balls. Note: The Ceiling Canopy (A) should be

snug against the ceiling and held tight with the mounting balls. If it is

not, adjust the length of the mounting screw on the Crossbar

Lock Washer

Flat

Washer

Swivel

Hex Nut

Glass Panel

Supply Wires

and Ground

Wire

Figure 2A

Supply

Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet

Box

Assembly Instruction Sheet

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) A19 Medium Base Bulbs 100W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
Assembly Instructions for Semi-flush Light (Step 1B - Step 6B) (Step 4A Continued) Assembly (AA) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (A) is secure, remove the mounting ball and Ceiling Canopy (A) and proceed to Step 5A. Part B, Part C and Part H will not be used in the assembly of the Semi-Flush Light fixture. Please set aside these parts.
PAGE 3
(Step 3B Contined) nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (A) is secure, remove the mounting ball and Ceiling Canopy (A) and proceed to Step 4B. FINISH: POLISHED CHROME STEP 4B - Wire Connections PENDANT LIGHT A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together.