Assembly Instruction

ManualsBrandsBrayden Studio ManualsCeiling LightsViveros 5 - Light Kitchen Island Linear Pendant

1of2

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Glass Panel

Lock Ball

Ceiling

Canopy

Quick Link

Small Loop

Socket Assemby

6” Rod

12” Rod

STEP 1 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

Figure 1

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 2 Install Nipple to Crossbar-

* Pliers is required for this step.

A. Thread Hex Nut (CC) to the middle of Nipple (DD). Place Lock

Washer (BB) over Nipple (DD) and then thread Nipple (DD) into

center hole of Crossbar (AA) until Nipple (DD) is about 0.375” above

Crossbar (AA).

B. Place Ceiling Canopy (A) over Nipple (DD) against the ceiling to

(Step 2 Continued)

determine the correct

position of Nipple (DD).

Thread Lock Ball (EE) onto

the Nipple (DD). Adjust

Nipple (DD) to allow Ceiling

Canopy (A) to rest against

the ceiling when held in

place by Lock Ball (EE).

C. Remove Ceiling Canopy (A)

and then tighten Hex Nut

(CC) against Crossbar (AA)

to secure in place.

Step A

Figure 2

STEP 3 Assemble Swivels, Rods and Fixture Body-

A. Determine Rods (D/E) to be assembled to Socket Assembly (F)

according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(D/E) and Small Loop (C). Thread Socket Assembly (F), the chosen

Rods (D/E) and Small Loop (C) together. Hand tighten until snug.

C. Pass the supply wires and ground wire through Quick Link (B) and

Ceiling Canopy (A). Attach Ceiling Canopy (A) to Small Loops (C) by

using Quick Links (B).

Suggested rods for Ceiling height :

8’ ceiling: use (1) 6” rod and (1) 12” rod

9’ ceiling: use (1) 6” rod and (2) 12” rods

10’ ceiling: use (2) 6” rods and (2) 12” rods

Supply Wires

and Ground Wire

Figure 3

(5)A19MediumBasebulbs100WMaximumor

(5)MediumBaseT9VintageBulbsarerecommendedbutnotsupplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) A19 Medium Base bulbs 100W Maximum or (5) Medium Base T9 Vintage Bulbs are recommended but not supplied. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
STEP 4 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box. Note: If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N" neutral wire before you cut the excess wire off. One is labeled N and the other labeled L.