Assembly Instruction

ManualsBrandsBrayden Studio ManualsBlack Outdoor Hanging LightsVitela Earth Black 1 -Bulb 19'' H Outdoor Hanging Lantern

(1)A21MediumBase150WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

1of2

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture

Loop

Hardware Contents

Crossbar

Lock

Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling Canopy

Quick Link

Fixture Chain

STEP 1 Install Fixture Loop,

Fixture Body and Cage together

A. Threading Fixture Loop (A) onto

Fixture Body (B), hand tighten

until sung.

C. Pass the top edge of the Cage

edge of the fixture hood of the

Fixture Body (B) and secure with

Lock Balls (D). Hand tighten until

sung.

Cage

Lock Ball

Figure 1

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of

the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place

another Lock Washer (BB) over the Nipple (DD) and then thread the

Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about

0.375” above the Crossbar (AA).

Step B

Step A

Figure 3

C. Remove the Canopy Lock

Ring (FF) from the Canopy

Chain Loop (EE). Place the

Ceiling Canopy (II) over the

Canopy Chain Loop (EE)

against the ceiling to

determine the correct position

of the Nipple (DD). Thread the

Canopy Lock Ring onto the

Canopy Chain Loop (EE).

Adjust the Nipple (DD) to

allow the Ceiling Canopy (II)

to rest against the ceiling

when held in place by the

Canopy Lock Ring (FF).

D. Remove the Canopy Lock

Ring (FF) and the Ceiling

Canopy (II). Tighten the Hex

Nut (CC) against the Crossbar

(AA) to secure in place.

Fixture

Body

STEP 4 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

links if needed.

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop and the

Canopy Chain Loop (EE), pull the supply wires through the Fixture

Chain (GG) alternating links. After the wires are through the Fixture

Chain (GG), pull the Supply Wires and the Ground Wire through the

Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with

one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and

attach the other end of the Fixture Chain (GG) onto the Canopy

Chain Loop (EE) with another Quick Link (HH). The fixture will now

hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving

Approximately 8” of wire extending from the Outlet Box.

E. Refer to Step 5 for wire connections.

F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) A21 Medium Base 150W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
How to Replace Glass Shade Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until tight. A. Unlock Lock Balls and remove Fixture Hood from the Cage . B . Unscrew Flat Head Screws on the Cage with Glass Shade, remove Tabs and Glass Shade from the Cage. C. Replace the Glass Shade with a new one and re verse above steps to reinstall prev iously removed parts back onto fixture.