Installation Instructions
For LED Wall Mount Fixture
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
A V E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F U S I B L E S O U D O D I S J O N C T E U R
.
PREPARATION
1. Shut off power at the fuse box or circuit breaker box.. If necessary
remove the old fixture and mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Take care not to lose any small parts necessary for
installation. Note: Do not remove the plastic film on the steel
mesh.
MOUNTING THE FIXTURE (FIG. 1)
3. Connect the white input wire from the driver (A) to the white wire
from the junction box. Connect the black input wire from driver (A) to
the black wire from the junction box and tuck the driver (A) and
connected wires carefully inside the junction box.(Note: To be
installed with a 4” round or octagon junction box)
4. Secure mounting plate(B)to the junction box using junction boxes
screws (E) (Size: 8-32*1/2”L). The side of the mounting back plate
marked “GND” must face out.
FINISHING THE INSTALLATION (FIG.1)
5. Put the nut (I) through gasket (C) and plastic gasket (J) and the hole
on the glass panel (K) and secure to bracket (L).
6. Attach bracket (L) to the bottom of fixture (G) with screws (M). Do
not have the glass (K) contact with the frame (G) during
assembly, to prevent the paint on the glass being scratched.
Adjust the gap between glass and fixture (G) evenly.
CONNECTING THE WIRES (FIG. 2)
7. Connect the red output wire from driver to the red input wire from
the led module. Connect the black output wire from driver to the
black input wire from led module see Fig. 2, making sure that all
wire connectors are secured. If your junction box has a ground wire
(green or bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to the mounting
plate (B) using the green screw (D) provided. Tuck the wire
connections neatly into the junction box.
8. Align fixture (G) over mounting plate (B) and tighten mounting and
secure with screws (F).Then remove the plastic film on the steel
mesh.
CAUTION /ATTENTION :When handling the fixture, do not apply
pressure to the LEDs. Hold the fixture by the base or fixture (G) only.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician without
cutting of wire and without damage to any decorative element to which
the fixture is attached. See installation steps for more details (Fig. 3)
Warning: Turn off power at the circuit breaker before replacing
LED module or LED driver.
a. Remove the bracket (L) from bottom of fixture (G), and remove
fixture (G) from mounting plate (B).
b. Remove the wire nuts located inside the fixture mounting plate (G),
remove screw (R) on fastener (S) to disconnect the LED module.
c. Remove screws (Q) to remove the acrylic panel (P). Remove
screws (O) to remove the LED module (N) from fixture (G) .
d. Reverse steps a-c for installing the new LED module.
e. Note: The LED module should be provided by a specified supplier.
f. For better heat dissipation the LED module should be applied with
thermal grease when re-lamping.
F
ig
.1
150 W CFL/LED or 600
W Incandescent/
Halogen 120 V
Single-pole lamp
dimmer
100W CFL/LED or 250W
Incandescent/ Halogen
120v
Fig 3
Fig.2
Single-pole/3-way
dimmer-
INSTALLATION INSTRUCTIONS
MIN 75
℃
Control type Maximum capacity
Ordering Information
■
Boxed
●
Clamshell
SUPPLY CONDUCTORS
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with C-L (CFL & LED) type and
Incandescent/Halogen type dimmers