OPERATOR’S MANUAL Safety, Operation & Service Information 100 Series One-Man Auger Model: BRPA180H Form: GOM08042002US, Version 1.0, Original Instructions • • • • • • • • Do not discard this manual. Keep manual readily available for reference during operation or when servicing product. Before operation, read and comprehend operator manual content. When ordering replacement parts, please supply the following information: model number, serial number and part number.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 TABLE OF CONTENTS 1 INTRODUCTION ……………………….…………… 3 2 INTENDED USE ……………..……………..……….. 3 3 TRAINING …………………………….……………… 3 4 SAFETY SYMBOLS ………….…………………….. 3 5 SAFETY INSTRUCTIONS ……………………..…... 3 6 MACHINE SPECIFICATIONS .…………..………… 6 7 STANDARD PRODUCTS & ACCESSORIES ….… 6 8 MACHINE SET-UP ………….……………….………. 7 9 APPLICATION THEORY & TECHNIQUES …….… 8 10 OPERATING INSTRUCTIONS …………………..… 9 11 MAINTENANCE INSTRUCTIONS ………………….
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 OPERATOR INSTRUCTIONAL DATA SHEET The following undersigned operators of Auger described and/or pertaining to this Operator Manual have received formal safety and operational information/instruction from undersigned owner(s)/instructor(s) in accordance to OSHA 29 CFR 1926.21 (b)(2) and/or applicable updated revisions pertaining to, but not necessarily limited to the: 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 1 INTRODUCTION Congratulations on your decision to purchase a Brave light construction product. It has been a continuing objective of Brave to manufacture equipment that delivers uncompromising value, service life and investment return. When you purchased this product, you also gained access to a team of dedicated, knowledgeable, support personnel that stand willing and ready to provide field support assistance.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 SPARK ARRESTER DISCLAIMER • WARNING DO NOT operate Auger on any forest covered, brush covered, or grass covered, unimproved land unless an approved spark arrester is installed on the muffler. The spark arrester must be maintained in proper working order by the owner and/or operator. In the State of California, the above is required by law. Other states may have similar laws. Laws will apply on US Federal lands.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 DETERMINATION OF POTENTIAL ABOVE SURFACE HAZARDS IN PROPOSED DIGGING LOCATION(S) TRANSPORTATION 1. Auger is designed for one operator to transport it by the operator handle to, while on, and from job site. 2. When transporting Auger in/on motor vehicle, gasoline tank breather vent (if so equipped) must be completely closed to eliminate fuel seepage. 3.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 6 MACHINE SPECIFICATIONS • • • • WARNING An Auger with improperly maintained engine throttle control will “spin” about its axis when operator loses full control. In event of this occurrence, do not attempt to stop engine by grasping rotating operator handle. DO NOT introduce any foreign object in an attempt to stop and/or block rotating handle. Instead, allow engine to exhaust its fuel supply.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 ACCESSORIES NOTE: All auger bits, bit extensions, blades and bit screw are for use in general purpose projects for a variety of soil conditions unless otherwise specified. All auger bits and auger bit extension drive connections are 1 inch (25 mm) diameter. Digging depth for all augers is 30 inch (762 mm) and auger extension is 15 inch (381 mm). Part # Description BR10639 2.25 inch (57 mm) Auger OD 3.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 • • • • • DANGER DO NOT smoke near fuel tank. DO NOT fill fuel tank with engine running or if it is hot. Allow ample time between each refueling for engine to cool. An ignition source in close proximity to fuel tank can be the source of an explosion, resulting in property damage and/or personal injury. Consult material supplied by engine manufacturer for information relative to proper fueling procedures. 3.
0 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 WARNING DO NOT use shovel and/or foreign object to remove loose soil from around hole area while operating Auger. • This can result in shovel and/or foreign object to become entrapped by rotating auger bit. DANGER To reduce potential for personal injury, stop Auger between each hole.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 14. Keep left side of operator handle as close to waist/leg/arm areas as possible for maximum leverage/control and minimize effects of “kickback” if obstruction is encountered when digging. 15. Keep arms close to upper body, back as vertical as possible, and bend legs as needed to minimize physical stress. 16. Position left foot forward of right foot and a comfortable distance apart. FIGURE 3 7.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 • • FIGURE 8 CAUTION Area can become hot to the touch. Wear gloves for added protection. FIGURE 10 20. Push lock handle down slightly to disengage upper detent position. Turn lock handle counterclockwise (to right) until it stops against vertical slot of lock bracket. FIGURE 10 21. Push lock handle down until it stops against bottom slot of lock bracket and engages transmission gear.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 ADDING/REMOVING NONFLIGHTED AUGER BIT EXTENSION For holes deeper than standard augers provide, a non-flighted auger bit extension increases digging depth 15 inches (381 mm). Additional operator experience, over introductory/novice skill levels, is required when using. Follow this accepted procedure to add non-flighted auger bit extension: 26. Dig to approximate full depth of auger bit following operating instructions.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 11 MAINTENANCE INSTRUCTIONS IMPORTANT: Keep external condition of operator handle and throttle control free of accumulation of moisture, dirt, pitch and other foreign substance that can provide a conductive pathway for energy to be transmitted. Throttle control should be maintained in clean, dry condition and free of all foreign materials.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 CHANGING AUGER TRANSMISSION GREASE Tools Required: 1 each, 7/16 inch (12 mm) wrench 1 each, #2 Phillips head screwdriver 1 each, torque wrench, 120 inch pounds (13.5 N.m.) capacity with 7/16 inch (12 mm) socket 1 each, plastic hammer 7. Remove gasket plus, primary gear and pinion assembly. 8. Clean interior surfaces of transmission cover and case plus, pressure relief valve with safety type solvent. 9. Clean each gear with safety type solvent.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 MAGURA® THROTTLE CONTROL MAINTENANCE PROGRAM For every 8 hours of actual operation and whenever throttle cable is replaced, the following maintenance program is to be followed: 1. CAUTION DO NOT operate Auger without rubber boot in proper location or in poor condition. • Without boot assembly, foreign material can accumulate within throttle control assembly.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 REPLACING WORN AUGER BIT BLADE Application: All 1 inch diameter drive connection, 4 inch diameter auger bits or larger. DANGER Wear safety eyewear and other safety apparel appropriate for the job application and/or job site environment. • Blade replacement process can create flying steel chips and/or other debris. • Caution all onlookers regarding the possibility of and/or to remain clear of flying debris.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 1. DANGER DO NOT smoke near fuel tank. DO NOT fill fuel tank with engine running or if it is hot. Allow ample time between each refueling for engine to cool. • An ignition source in close proximity to fuel tank can be the source of an explosion, resulting in property damage and/or personal injury. • Consult material supplied by engine manufacturer for information relative to proper fueling procedures. • • • 2.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 NOTE: Centrifugal clutch drum/pinion shaft assembly removal and installation will require a level working platform of sufficient size and appropriate height. As an alternative, the transmission output driveshaft can be securely mounted in suitable bench vise. 1. Drain fuel from fuel tank into a UL, CSA or UN marked, European ADR regulation approved fuel container and oil from engine crankcase.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 ENGINE SERVICE Consult applicable material supplied by engine manufacturer for specific service and maintenance information regarding: 1. 2. 3. 4. 5. 6. 7. 8. muffler spark plug air filter carburetor adjustment maintenance schedule engine oil change troubleshooting short and long term storage 14 STORAGE Keep this information stored with Operator Manual for Auger so it will always be available for use when engine requires service or maintenance.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.0 6. Apply light coat of protective grease to transmission driveshaft to prevent formation of rust. 7. Store Auger with operator handle level with ground to prevent transmission oil draining from breather vent and damaging surrounding environment and to minimize potential for crankcase oil entering combustion chamber and creating hydraulic lock up. 8.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
100 SERIES ONE-MAN AUGER FORM GOM08042002US, VERSION 1.
