Instructions / Assembly

ManualsBrandsBrassCraft ManualsGas Fittings & ConnectorsProCoat 1/2 in. MIP x 1/2 in. MIP Stainless Steel Gas Connector 1/2 in. O.D.

WARNING: DO NOT stretch the connector to

make it t. Connector must be long enough to

allow the appliance to be positioned at its farthest

anticipated connected distance from the gas supply

without stretching, twisting or bending smaller that a

1-1/2 internal diameter (diameter of a golf ball).

WARNING: DO NOT trap connector against sharp

edges or corners.

CAUTION: DO NOT kink, twist or bend connector sharply.

6. Turn manual shut-off valve on to allow gas to enter system.

WARNING: DO NOT TURN ON APPLIANCE until all

connections have been leak tested!

WARNING: DO NOT USE matches, candles, open

ames or other sources of ignition to leak test

connections!

7. Test all connections with leak test solution provided,

or with clear soap and water solution; bubbles will

indicate a leak. If a leak is detected, turn off gas

supply before further tightening connections. Water

rinse and towel dry connector once test is complete.

8. Wait at least 10 minutes to be certain that all vapors

have dissipated. If leak test conrms connections do

not leak gas, and you do not smell any gas,

THEN light pilot(s) and turn on appliance.

Tools Needed for Installation:

• (2) 10 in. adjustable wrenches

• Pipe dope or gas pipe thread tape

• Leak detection solution

325.01 Rev. 11/19

Brasscraft Manufacturing Co., 39600 Orchard Hill Place Novi, Michigan 48375-5331

TOLL-FREE: 877.272.7755 FAX: 248.305.6011 www.brasscraft.com

Manufacturer assumes no responsibility for failure due to improper installation.

brand is a trademark of Brasscraft Mfg. Co.

El fabricante no asume ninguna responsabilidad si la instalación no se hace de acuerdo al instructivo.

BrassCraft

brand es una marca registrada de Brasscraft Mfg. Co.

Gas Connector Maximum Flow Capacity

Part #

Color Code

12 in 18 in 24 in 30 in 36 in 48 in 60 in 72 in

Gas Connector with Standard Fittings

CSSL

1/4 BTU’s 48,000 43,800 40,000 36,400 33,400 28,300 24,900 23,100

Purple Watts 14,067 12,837 11,723 10,668 9,789 8,294 7,297 6,770

CSSD

3/8 BTU’s 102,000 93,100 85,000 77,100 71,100 60,500 53,200 49,100

Green Watts 29,893 27,285 24,911 22,596 20,837 17,731 15,591 14,390

CSSC

1/2 BTU’s 180,000 164,200 150,000 136,000 125,000 106,000 93,200 86,000

Gold Watts 52,752 48,122 43,961 39,858 36,634 31,066 27,314 25,204

Safety+Plus® (Gas Connector with Excess Flow Valve Attached)

CSSL

1/4 BTU’s 42,000* 37,400* 36,800* 36,400 33,400 28,300 24,900 23,100

Purple Watts 12,308* 10,960* 10,784* 10,668 9,789 8,294 7,297 6,770

CSSD

3/8 BTU’s 102,000 93,100 85,000 77,100 71,100 60,500 53,200 49,100

Green Watts 29,893 27,285 24,911 22,596 20,837 17,731 15,591 14,390

CSSC

1/2 BTU’s 122,000* 118,000* 115,000* 111,000* 107,000* 106,000 93,200 86,000

Gold Watts 35,754* 34,581* 33,702* 32,530* 31,358* 31,066 27,314 25,204

Note: Connecting the safety valve lowers these values below the Z21.24/CSA 6.10 and Z21.75/CSA 6.27 standards

Listings & Certications:

Components CSA listed to ANSI Z21.24 / CSA 6.10 standard “Connectors for

Gas Appliances”

Components CSA listed to ANSI Z21.75 / CSA 6.27 standard “Connectors for

Outdoor Gas Appliances & Manufactured Homes”

NOTE: This connector meets or exceeds the minimum allowable capacity

as determined under test conditions specified in ANSI Z21.24 • CSA 6.10.

Straight length capacity rated in BTU per hr. using: 0.64 SP. Gr., 1000 BTU per

Cu Ft. Gas at 0.50 inch Water Column Pressure Drop. The capacity at 50 Pa

(0.2 inch water column) pressure drop can be determined by multiplying the

BTU per hr. listed in the table above by 0.632