Installation Guide
425.10 11/19
CAUTION: DO NOT INSTALL THIS PRODUCT UNTIL YOU READ AND
UNDERSTAND ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY, PROPERTY DAMAGE
OR PRODUCT FAILURE.
Plumbing professionals have trusted BrassCraft® water supplies
for more than 70 years. We invented the exible water supply and
continue to be a leader in quality and innovation. From vinyl to our
premium polymer braided connectors, BrassCraft® is your one
source for a full line of quality water connectors.
INSTALLATION INSTRUCTIONS
Manufacturer assumes no responsibility for failure due to improper installation.
CAUTION:
BE SURE TO SHUT OFF WATER BEFORE STARTING.
• For Use with Water in Accessible Locations Only.
• For Use on Hot & Cold Water Applications.
• No Cutting, Bending or Flaring Required.
For use with iron pipe or compression valve outlets.
• Operating temperature 40-160˚F intermittent to 180˚F.
• Operating pressure: 125 psi maximum.
• Certied to NSF 61/9 for drinking water.
Universal Faucet Water Connector Kit
Figure 1
FOR 3/8 IN. COMPRESSION
OUTLET SHUT-OFF STOPS
Figura 1. Para llave de paso con
salida de 9,5mm tubería de hierro.
PIPE ADAPTOR
Adaptador de tubo
CONE WASHER
Rondana cónica
1/2 in. IRON
PIPE
OUTLET
Salida de tubo
CONNECTOR
Conector
3/8 in. COMPRESSION
Compresión
3/8 in.
COMPRESSION
OUTLET
Salida de tubo
CONNECTOR
Conector
3/8 in. COMPRESSION
Compresión
COMPRESSION
ADAPTOR
Adaptador de compresión
FLAT WASHER
Rondana
1/2 in.
COMPRESSION
OUTLET
Salida de compresión
INSTALLATION INSTRUCTIONS (CONTINUED)
CAUTION:
BE SURE TO IDENTIFY THE CORRECT WATER SUPPLY CONNECTION
BEFORE BEGINNING INSTALLATION PROCEDURE. APPLICATION OF THIS CONNECTOR
WITH THE INCORRECT WATER SUPPLY CONNECTION MAY CAUSE LEAKS.
1. Shut off water supply at valve.
2. Remove old supply tubes.
3. Thread wing nut of connector onto faucet shank and hand tighten only.
4. Determine valve outlet size.
• If outlet is 3/8 in. compression, thread new connector directly onto stop outlet.*
Hand tighten, then wrench tighten 1/4 turn more. (Figure 1)
• If outlet is 1/2 in. compression, place at washer into compression adaptor and
thread onto stop outlet. Hand tighten, then wrench tighten 1/4 turn more. (Figure 2)
• If outlet is 1/2 in. iron pipe, place cone washer into iron pipe adaptor and thread
onto stop outlet. Hand tighten, then wrench tighten 1/4 turn more. Use a cloth on
nut to protect nish. (Figure 3)
5. Thread connector onto adaptor. Hand tighten, then wrench tighten 1/4 turn more.
Tools Needed for Installation: • Wrench • Protective cloth
*NOTE: Connector includes washers, DO NOT USE THREAD SEALANT.
Figure 2
FOR 1/2 IN. COMPRESSION
OUTLET SHUT-OFF STOPS
Figura 2. Para llave de paso con
salida de 12,7mm tubería de hierro.
CONNECTOR
Conector
3/8 in. COMPRESSION
Compresión
Figure 3
FOR 1/2 IN. IRON PIPE
OUTLET SHUT-OFF STOPS
Figura 3. Para llave de paso con
salida de 12,7mm tubería de hierro.
©2019 Brasscraft Manufacturing Company
Brasscraft Manufacturing Co., 39600 Orchard Hill Place Novi, Michigan 48375-5331
TOLL-FREE: 877.272.7755 FAX: 248.305.6011 www.brasscraft.com
Manufacturer assumes no responsibility for failure due to improper installation.©2019 Brasscraft Manufacturing
Company, Novi, MI 48375-5331 U.S.A. All Rights Reserved. www.brasscraft.com Designed, Machined and
Assembled in the U.S.A. BrassCraft
®
brand is a trademark of Brasscraft Mfg. Co.
El fabricante no asume ninguna responsabilidad si la instalación no se hace de acuerdo al instructivo.
Diseñado, Maquinado y Ensamblado en E.U.A. BrassCraft
®
brand es una marca registrada de Brasscraft Mfg. Co.