Installation Manual

ManualsBrandsBraeburn ManualsEquipment5220

Detailed

Installer Guide

Programmable Thermostats

Speciﬁcations

Installation and Wiring

Quick Reference

Installer Settings

System Testing

• Possible electric shock or damage to equipment can occur.

• Disconnect power before beginning installation.

Caution

This thermostat requires 24 Volt AC Power or 2 properly installed “AA” Alkaline

batteries for

proper operation. When connecting 24 Volt AC Power the batteries may

be installed as a backup.

For use only as described in this manual. Any other use will void warranty.

5020

Up to 2 Heat / 1 Cool Heat Pump

1 Heat / 1 Cool Conventional

5220

Up to 3 Heat / 2 Cool Heat Pump

Up to 2 Heat / 2 Cool Conventional

Warning

For installation by experienced service technicians only.

This thermostat is compatible with:

• Single stage heat / cool conventional and heat pump systems

• Single stage heat pumps with auxiliary heat

• Heat pump systems up to 3 stages of heating and 2 stages of cooling (5220 only)

• 250 – 750 millivolt heating only systems

• 2 or 3 wire hydronic zone systems

Electrical and control speciﬁcations:

• Electrical Rating: 24 Volt AC

• 1 amp maximum load per terminal

• AC Power: 18 – 30 Volts AC

• DC Power: 3.0 Volt DC (2 “AA” Alkaline Batteries Included)

• Control Range: 45° – 90° F (7° – 32° C)

• Temperature Accuracy: +/- 1° F (+/- .5° C)

• Outdoor Temperature Display Range: -40° - 120° F (-40° - 49° C)

Terminations

• 5020: Rc, Rh, W1/E, C, Y1, O/B/V3, G, S2, S1

• 5220: Rc, Rh, W2, W1/E/W3, C, L, Y2, Y1, O/B/V3, G, S2, S1

Speciﬁcations

5020W-100-05

Model number is located on back of thermostat.

PREMIER

SERIES

Summary of content (15 pages)

PAGE 1
® Detailed Installer Guide PREMIER SERIES Programmable Thermostats 5020 Up to 2 Heat / 1 Cool Heat Pump 1 Heat / 1 Cool Conventional 5220 Up to 3 Heat / 2 Cool Heat Pump Up to 2 Heat / 2 Cool Conventional Model number is located on back of thermostat. 1 Specifications 2 Installation and Wiring 3 Quick Reference 4 Installer Settings 5 System Testing Warning For installation by experienced service technicians only. Caution • Possible electric shock or damage to equipment can occur.
PAGE 2
2 Installation and Wiring Warning Disconnect power before beginning installation. Thermostat Location Install the thermostat approximately 5 feet (1.5m) above the floor in an area that has a good amount of air circulation and maintains an average room temperature. Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls.
PAGE 3
2 Provide Power C + + 24VAC Power Terminal (C) Batteries Installed as Shown • For 24 Volt AC power, you must connect the common side of the transformer to the C terminal on the thermostat sub-base. In dual transformer installations, the transformer common must come from the cooling transformer. • For battery power, insert the 2 supplied “AA” type alkaline batteries into the battery compartment located in the rear housing of the thermostat.
PAGE 4
3 Connecting Your Wires (continued) Wiring Terminations for model 5220 Terminal Function Description Rc Input 24 Volt AC Cooling Transformer (Dual Transformer Systems Only) Rh Input Power Connection (24 Volt AC Heating Transformer or Millivolt Power Source) G Fan Control Output W1 / E / W3 Output (W1) 1st Stage Conventional Heat, (E) Emergency Heat, (W3) 3rd Stage Auxiliary Heat 2nd Stage Conventional Heat W2 Output O / B / V3 Output (O
PAGE 5
Conventional Systems Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. Shaded areas do not apply to the 5020.
PAGE 6
Heat Pump Systems - Typical Wiring Configurations NOTE: The “System Type” option will be configured in the Installer Settings section. Shaded areas do not apply to the 5020.
PAGE 7
4 Attach Thermostat to Sub-Base UP UP L S1 C S2 W1/E /AUX11 /AUX G W2/ AUX2 Y1 W3/ O/B Y2 RH A RC H INSTRUCTIONS DAY/TIME 1) Line up the thermostat body with the sub-base. 2) Carefully push the thermostat body against the sub-base until it snaps in place. 3) Insert Quick Reference Card into slot on top of thermostat. NOTE: This thermostat ships configured as a 1H/1C conventional thermostat. Confirm installer settings. See page 10.
PAGE 8
3 Quick Reference 8 7 1 9 10 11 12 13 2 14 BACK NEXT 3 4 5 6 Thermostat Display 1 Room Temperature....................... .Displays the current room temperature 2 Set Temperature........................... .Displays the current set point temperature 3 BACK Indicator*............................ .BACK button is active 4 NEXT Indicator*............................ .NEXT button is active 5 Outdoor Temperature Indicator.... .
PAGE 9
22 INSTRUCTIONS 23 15 BACK NEXT 18 19 DAY/TIME 16 17 20 21 24 Thermostat 15 Reset Button ................................ .Resets current time, program and user settings 16 SYSTEM Button............................. .Selects the system you want to control 17 DAY/TIME Button........................... .Sets the current time and day of the week PROG Button................................. .Selects programming mode or press for 3 seconds to select SpeedSet® BACK Button*........
PAGE 10
4 Installer Settings The Installer Settings must be properly configured in order for this thermostat to operate correctly. The Installer INSTRUCTIONS Settings are menu driven. The portion of these settings that do not apply to your setup will be skipped. These settings are indicated below with comments. More detail on each setting follows this table. 1. Press and hold down the RETURN and buttons for 3 seconds. 2. Release both buttons and the first installer setting will be displayed. 3.
PAGE 11
No. Installer Setting (Notes follow this table) Factory Default Setting Options Comments (More information follows this table) 7 1st Stage Differential 0.5 DIF1 0.5, 1.0 or Select a 1st stage temperature differential of 2.0 DIF1 .5°, 1° or 2° F (0.2°, 0.5° or 1.0° C) 8 2nd Stage Differential 2.0 DIF2 1.0, 2.0, 3.0, Select a 2nd stage temperature differential of [note 2] 4.0, 5.0 or 1°, 2°, 3°, 4°, 5° or 6° F (0.5°, 1.0°, 1.5°, 2.0°, 6.0 DIF2 2.
PAGE 12
NOTES - Installer Settings 1 2 3 4 5 6 7 8 9 10 11 Only available if Residential profile was selected in option 1. Only available if a 2 or 3 stage system type was selected in option 6. Only available if a Conventional system was selected in option 6. Only available if a 2 or 3 stage Heat Pump system was selected in option 6. Only available if a Heat Pump system was selected in option 6. Only available if the 24 Volt AC common wire is connected to the C terminal.
PAGE 13
15 AC Power Interrupt Warning [note 6] – When enabled, the thermostat will display an outage warning when AC power to the thermostat is lost. 16 Short Cycle Protection [note 7] – Selects the number of minutes the cooling compressor will be locked out after turning off. This short cycle protection is also active in the heat mode if a heat pump system was selected in Option 6. 17 Residual Cooling Fan Delay [note 7] – Selects a delay for the system fan after the cooling compressor has turned off.
PAGE 14
5 System Testing Warning Read Before Testing • Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty. • Do not select the COOL mode of operation if the outside temperature is below 50º F (10º C). This could possibly damage the controlled cooling system and may cause personal injury.
PAGE 15
® Limited Warranty When installed by a professional contractor, this product is backed by a 5 year limited warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full copy of this warranty: · Visit us online: www.braeburnonline.com/warranty · Phone us: 866.268.5599 · Write us: Braeburn Systems LLC 2215 Cornell Avenue Montgomery, IL 60538 5 YEAR LIMITED WARRANTY Store this manual for future reference.