User's Manual

NOTE: See the wireless remote sensor manual for complete installation and use instructions.
Compatible Wireless Remote Sensors
WirelessRemoteIndoorSensor(s)–4sensorsmaximum
WirelessRemoteOutdoorSensor–1sensormaximum
WirelessRemoteHumiditySensor–1sensormaximum
NOTE: No more than 4 wireless remote sensors can be connected.
Pairing Wireless Remote Sensors
1 PressandholdtheHOLD and RETURNbuttonsfor3seconds.
2PressNEXT untilthewordSENSappearsinthedisplayandthesymbolashes.
3 Aftertheremotesensorispowered,pressandholdtheCONNECTbuttononthesensorfor3seconds
and release.
4 Theremotesensorwillenterpairingmodefor60seconds.Duringthistimetheblueindicatoronthewireless
 remotesensorwillashonceevery2seconds.
5Whenpaired,thethermostatdisplaywillchangeandindicatewhichremotesensorhasbeenpaired(see
 Table1).Thesymbolwillstopashingandtheblueindicatorontheremotesensorwillturnonfor
 60seconds.
6 Topairanotherwirelessremotesensor,pressNEXTandrepeatsteps3-5.
7PressRETURNatanytimetoexit.
NOTE: Sensors that have already been paired will appear in the thermostat display first, with a solid symbol.
Using Wired Remote Sensors
•OnewiredindoororwiredoutdoorremotesensorcanalsobeconnectedtothethermostatsS1andS2
 terminalsonthecontrolmoduleusing2-wirethermostatcable.
•Youcannotmixwiredandwirelessremotesensorsofthesametype(i.e.mixinganindoorwirelessremote
 sensorandanindoorwiredremotesensor).
Replacing a Thermostat
Ifyouarereplacingathermostatthatispairedwithanexistingwirelesssensor,youwillneedtocleartheremote
sensorandpairitagainwiththenewlyinstalledthermostat.
1 Installthenewthermostat.
2 Onthewirelessremotesensoryouwanttoclear,pressandholdtheCONNECTbuttonfor10secondsuntilthe
red indicator turns on.
3ReleasetheCONNECTbuttonandtheblueandredindicatorwilleachashoncetoindicatethesensorwas
 successfullycleared.
4 Pairtheremotesensoragain.
Replacing a Sensor
Ifyouarereplacingawirelessremotesensorthatispairedwithanexistingthermostat,youwillneedtoclearthe
thermostat’sremotesensorconnectionbeforepairingthenewwirelessremotesensor.
1 Installthenewwirelessremotesensor.
2 ThermostatremotesensorsettingsareclearedbyadjustingInstallerSetting29toCLR1(seesection4).
 Thissettingclearsalltheremotesensorspairedwiththethermostat.
NOTE: Be careful not to select CLR3 unless you want to clear all the thermostat settings.
3Oncetheremotesensorsettingsareclearedyouwillneedtopairyournewwirelessremotesensor.Youwill
 alsoneedtopairanyotherexistingwirelessremotesensorsthatwerepreviouslyconnected.
5
Wireless Remote Sensors
IDS1, IDS2, IDS3 or IDS4 RemoteIndoorSensor1-4
HMS  RemoteHumiditySensor
ODS  RemoteOutdoorSensor
Table 1
Installer Guide 16