User's Manual

No. Installer Setting Factory Setting Comments
(
Notes follow this table) Default Options (More information follows this table)
 10 1stStageFanControl HG FAN 1 HG FAN 1 Selectfor1ststageGasheating
[note 3] HE FAN 1 Selectfor1ststageElectricheating
 11 EmergencyHeat] HE EMER HE EMER SelectforElectricEmergencyHeat
  FanControl[note 4] HG EMER SelectforGasEmergencyHeat
 12 ReversingValve REVO REVO SelectforcoolactiveReversingValve(Oterminal)
  (O/BTerminal)[note 5] REVB SelectforheatactiveReversingValve(Bterminal)
 13 FossilFuel AE AUX AE AUX SelectforElectricAuxiliaryheat(withcompressor)
  BackupHeat[note 4] AG AUX SelectforGasAuxiliaryheat(withoutcompressor)
 14
CompressorPowerOutage oF CPOP oF CPOP DisablesPowerOutageLockoutDelay
  Protection [notes 4, 6] on CPOP EnablesPowerOutageLockoutDelay
 15 ACPowerInterrupt
AC oF MONR AC oF MONR DisablesACPowerInterruptWarning
  Warning[note 6] AC on MONR EnablesACPowerInterruptWarning
 16 CompressorShort 5 CSCP 5, 4, 3, 2or Selectacompressorshortcycleprotectiondelayof5, 
  CycleProtection[note 7] 0 CSCP  4,3,2or0minutes
 17 ResidualCooling 60 FAN 90, 60, 30  SelectaResidualCoolingFanDelayof90,60,
  FanDelay[note 7] or 0 FAN 30 or 0 seconds.
 18 AdaptiveRecovery oF REC oF REC DisablesAdaptive(early)Recoverymode
  Mode(ARM™) [note 8] on REC EnablesAdaptive(early)Recoverymode
 19 IndoorRemoteSensor I SENS I SENS Temperatureissensedfromthermostatonly.
  Control*[note 9] E SENS Temperatureissensedfromremotesensoronly.
A SENS Temperatureiscombinedwiththethermostatand 
the remote sensor.
 20 LockoutSecurityLevel 2 LOCK 2 LOCK Iflocked–Completelockoutisenabled
1 LOCK Iflocked–Partiallockoutisenabled(SpeedBar
®
is
        stillfunctional)
 21 AutoChangeover 3 BAND 2, 3, 4 or 5 SelectaDeadBandof2°,3°,4°or5˚F  
  DeadBand[note 10] BAND  (1°,2°or3°C)forAutoChangeovermode.
22 CompressorBalance NO BALC NO BALC DisablesBalancePoints
Point[notes 4, 11] 0-50 BALC SelectaCompressorBalancePointof0°-50°F
23 AuxiliaryHeatBalance NO BALA NO BALA DisablesBalancePoints
Point[notes 4, 11] 70-40 BALA SelectaAuxiliaryHeatBalancePointof70°-40°F 
24
HeatSetPointUpperLimit 90LIM 90-60 LIM SelectaHeatSetPointUpperLimitof90°-45°F
25 CoolSetPointLowerLimit 45LIM 45-80 LIM SelectaCoolSetPointLowerLimitof45°-90°F
[note 7]
26 Humidication OFF OFF DisablesHumidication
[note 12] DEP EnablesDependantHumidication
IND EnablesIndependentHumidication
 27 AutoHumiditySet AUTO AUTO Enablesautomatichumiditycontrolbasedon
  PointLimit[notes 11, 12] outdoor temperature.
MAN Enablesmanualhumiditycontrolfromthermostat.
 28 Dehumidication OFF OFF DisablesDehumidication
[note 12] NI  Normallyinactive(open)relay
NA Normallyactive(closed)relay
 29 InstallerClear CLR0 CLR0 ClearOff-Nochangesmadetosettings
CLR1 Clearsconnectionwithwirelessremotesensors
CLR2 Clearsconnectionwithcontrolmodule
CLR3 Clearsallthermostatsettings(factorydefaults)
NOTES - Installer Settings
1 OnlyavailableifResidentialprolewasselectedinoption1.
2 Onlyavailableifa2or3stagesystemtypewasselectedinoption6.
3 OnlyavailableifaConventionalsystemwasselectedinoption6.
4 Onlyavailableifa2or3stageHeatPumpsystemwasselectedinoption6.
5 OnlyavailableifaHeatPumpsystemwasselectedinoption6.
6 Onlyavailableifthermostatis24VACpowered(RandCterminals).
7 Notavailableifaheatonlyhydronicsystemisselectedinoption6.
8 Onlyavailableifaprogrammableprolewasselectedinoption2.
9 OnlyavailableifaBraeburn®indoorremotesensorwasconnected.
10 Onlyavailableifautochangeoverwasenabledinoption5.
11 OnlyavailableifaBraeburnoutdoorsensorwasconnected.
12 OnlyavailableifaBraeburnwirelesshumiditysensorwasconnected.
Detailed Explanation of Installer Settings (also see NOTES above):
1 Profile–Selectsaresidential(RES)orcommercial(COMM)prole.Ifresidentialisselected,4programming
 eventsperdayareavailable.Ifcommercialisselected,2event,7dayprogrammingisavailable.
2 Programming Mode [note 1]–Selectstheprogrammingmode,eitherfull7dayor5-2day(weekday/
 weekend)programmingornon-programmable.
3 Clock Type–Selectseithera12houror24hourclock.
4 Temperature Scale–Selectsatemperaturescaleofeither°For°C.
5 Auto Changeover–Selectsautochangeoveronoroff.Whenautochangeovermodeisenabledand
selected, thesystemautomaticallyswitchesbetweenheatingandcoolingmodes.Thereisa5minutedelay
 whenswitchingfromheatingtocoolingorcoolingtoheatinginautochangeovermode.
NOTE: Also see “Auto Changeover Dead Band” in option 21.
6 System Type–Selectsthesystemtypeforyourinstallation.NOTE: Changes made to this option will reset
options 7 through 15 back to their default values dependant on the system type.
7 1st Stage Differential–Selectsa1ststagetemperaturedifferential.
8 2nd Stage Differential [note 2]–Selectsa2ndstagetemperaturedifferential.
9 3rd Stage Differential [note 2]–Selectsa3rdstagetemperaturedifferential.
10 1st Stage Fan Control [note 3]–Selectsa1ststagefancontrolofeithergasorelectricheat.
11 Emergency Heat Fan Control [note 4]–Selectsemergencyheatfancontrolofeithergasorelectricheat.
12 Reversing Valve [note 5]–SelectstheoutputstateoftheO/Bterminal.SelectOforthisterminaltobe
 activeinthecoolmodeorselectBforthisterminaltobeactiveintheheatmode.
13 Auxiliary Fossil Fuel Heat Pump Control [note 4]–Whensettoelectric(AEAUX),boththecompressor
 (1ststage)andauxiliarystage(s)willrunwhenacallforauxiliaryheatismade.Whensettogas(AGAUX),
 thecompressorstage(s)willbelockedoutoneminuteafteracallforauxiliaryheat.NOTE: This option can
be overridden if setting an auxiliary heat balance point in Option 23.
14 Compressor Power Outage Protection [notes 4, 6]–Selectspoweroutageprotectiononoroff.When
 enabled,thisthermostatwillprovidecoldweathercompressorprotectionbylockingoutthecompressor
 stage(s)ofheatingforaperiodoftimeafterapoweroutagegreaterthan60minutes.
13 Installer Guide