Copyright This manual is copyrighted with all rights reserved. No portion of this manual may be copied or reproduced by any means without the prior written consent of BRADY. While every precaution has been taken in the preparation of this document, BRADY assumes no liability to any party for any loss or damage caused by errors or omissions or by statements resulting from negligence, accident, or any other cause.
BRADY Warranty Our products are sold with the understanding that the buyer will test them in actual use and determine for him or herself their adaptability to phisher intended uses. BRADY warrants to the buyer that its products are free from defects in material and workmanship, but limits its obligations under this warranty to replacement of the product shown to BRADY s satisfaction to have been defective at the time BRADY sold if.
Technical Support and Registration Contact Information For repair or technical assistance, locate your regional Brady Technical Support office by going ta: United States: bradyid.comiechsupport Canada: bradycardia contact-us Mexico: brad yid com mes-contactable Latin America: Europe: bradycardia. commiserates Australia: brad yid Asia Pacific: Registration Information To register your printer go to bradycardia.
Contents 1 = introduction Unpack Your Printer Accessories .. Register Your Printer . System Specifications .. Physics! and Environmental Characteristics External View Power Source... Battery Safely Loading AA Alkaline Batteries | Loading the Lithium lon Battery Pack Remove Lithium Battery AC Power Adapter Attaching the Adapter Charging the Lithium lon Battery Pag Media Cartridge. Changing the Label Cartridge | Recycling the Label Cartridge | Materials Power On...
inserting Text . Deleting Text .. Clear Data Cancel Functions Error Messages Font Size .. Printing a Label Multi-Print 3 « Formatting Symbols... Remove a Symbol International Character Set | Ate and Time... Timestamp Bar code Add a Bar code Data matrix and QR Codes Add a Material or OR Code Serialization... How Serialization Works Examples of Serialization . Using Letters in Serialization Multi-Letter Serialization Add Serialization 4 = File Management File Naming Standards.
Cleaning the Printer. Display Screen Internal Components A = Symbols Assorted Miscellaneous Miscellaneous {Russian only}. Greek. Lab B = Supported ASS Characters Bar codes .. Code 38 Code 128...
BRADY 1 Introduction The M210/M210 LAB Label Printer is a rugged, highly mobile printer designed to print on a variety of continuous and per-sized materials. With label widths from 25" to 757, this libeler meets the demands of rigorous job sites printing up to 100 labels per day. Key features include: « Pr-loaded application design guides to simplify label creation for common application types.
Unpack Your Printer The following items are included in the standard M21O/M210LAB Label Printer package: Accessories The following items are accessories available for the M210 Label Printer (M210-LAB Label Printer) . RS Sons M21-750-400 0.75" (19.1 mm) Multi-Purpose White Nylon Cartridge with the M210 or M21-750-7428 Chemical and Temperature Resistant Label Cartridge with the M210-LAB Quick Start Guide Label Printers.
System Specifications The M210/M2 LAB Labs! Printer has the following specifications: « Eighty 1.66 ibs {0.753 kg} « Thereat Transfer Print Mechanism, 203 DPI print resolution + Elastoplast ABC-style keypad «Print Width (18.1 mm) maximum label width + Maximum length for labels with alphanumeric characters: 98.9 inches (253.7 em} « Maximum characters that can be printed: 50 + Prints up lo 1800 x Z-inch (12. 7mm x 50.
External View 4 Power key 8 2 Function keys 9 3 Symbols and characters 10 4 Secondary function key 11 5 Navigation pad with ENTER key 12 8 Set language and unit defaults 13 7 Print key 14 Cutter lever Cartridge bay locking lever Cartridge bay with cartridge AC adapter port Cartridge eject button Battery compartment Finger tabs on battery compartment cover Note: There are NO PC connection pores on the printer, therefore it CANNOT be connected toa PU.
Power Source Power is supplied to the printer by six AA alkaline batteries, a Lithium fon (Lion) battery pack, power adapter. To maintain maximum printer performance use basic AA alkaline batteries, NOT rechargeable or Ultimate Lithium AA batted es. The optional Li-Kan battery pack is rechargeable, but must be removed from the printer and attached fo the AC power adapter for charging to take place.
battery terminals. ; WARMING Do not allow metal or other conductive materials to touch the Do not dismantle, open. or shred cells of batteries. Bo not expose cells or batteries to heat or fire. Av old storage in direct sunlight. Ba not short-circuit a cell or a battery. Do not store calls or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. Do not remove a cell or battery from its original packaging until required for dse.
Loading AA Alkaline Batteries On the back of the printer, insert 8 AA alkaline Re-insert the battery road squeeze the finger tabs batteries, observing correct hinge at the top of the located on both sides of polarity. (Do not use compartment and push the battery compartment rechargeable AA batteries down on the battery road, then swing the or Ultimate Lithium AA compartment door, battery compartment door batteries). snapping it into place. up and out. (The door will crane off.
Loading the Lithium lon Battery Pack When using an BATTERER Lithium lon battery pack, please consult the instructions enclosed with the battery pack for the charging procedure. Cn the back of the printer, squeeze the finger tabs located on both sides of the battery compartment door, then swing the battery compartment door up and out {The door will come off.
Remove Lithium Battery Squeeze the finger tabs Placing your thumb at the Grasp the raised battery acted on both sides of the base of the printer, use your and pull it up and out from battery compartment door, forefingers to gently pull up the bottom contact slots. then swing the battery on the raised portion of the compartment door up and battery. This releases the out. {The door will come top of the battery from the off} contacts.
AC Power Adapter The printer can be powered by an AC/DC power adapter. The AC/DC power adapter can also be used to recharge the BATTERER battery pack outside of the printer. Waking! Use only the OV DC. Brady ACIDIC adapters. shown below. for A sunning power to the M210/M210-L AB Label Printers. Attaching the Adapter The printer can be powered through a designated AT power adapter. Note: The lithium lon battery dues NOT charge within the printer when using the AC adapter.
Charging the Lithium fon Battery Pack The lithium on battery pack accessory cannot be charged in the printer. The battery pack must be removed from the printer and charged using the M210-AC AC adapter. To use the printer while charging the battery, insert & AA alkaline batteries in the battery compartment. Attaching the Adapter to the Battery Pack 1. insert the round end of the adapter cable into the plug-in port on the lower left side of the battery pack. 2.
Media Cartridge The M21 media and ribbon supplies are combined in a plastic cartridge for easy one-step loading and have been optimized for the Label Printers. Cartridges are offered as continuous tapes between 0.25" 0.75" {8.35mm 18. 1mm) or as per-sized labels in multiple material types. Note: For specific compatibility with older Brady Label Printers, please refer to information provided for each individual catalog number.
Changing the Label Cartridge To UNICEF the Rush the eject button Place a new cartridge in the cartridge, turn the on the back of the cartridge bay and push down ung] locking lever left to printer, then lift the the cartridge snaps inch place. the horizontal cartridge oul of the position. printer. Turn the locking lever right to the vertical position. Eject Button a Locking Lever flocked) Locking Lever {unlocked} if the cartridge is empty, recycle according lo local regulations.
Recycling the Label Cartridge Cartridges need fo be recycled in accordance with local regulations. Before recycling, the used cartridges must be pulled apart to release the individual components. These various components must then be recycled in the correct recycling bins. Materials «14-inch blade Flathead screwdriver « Safely Glasses + Safely Gloves CAUTION! ALWAYS wear Personal Protective Excitement when dismantling a A cartridges.
[on] 2 . Power On Printer Version Tuo turn the system on or off 1. Press Power Ea 2. Watch the screen closely for the version number which displays briefly. Note: Screen shown above is a sample only; version number on your product may differ. if you missed seeing the version number and need to know what it is? 3. Remove whichever type of batteries are installed. 4. Press and hold the power button for 10 seconds. 5. Reinstall batteries while watching the screen.
Editing Screen The editing screen enables you to view formatting features directly on the screen while you are entering and editing data.
Keypad Navigation and Editing Keys Bei Power Ascription Turns on the printer Navigation Keys Navigation keys: + Int a ne of text, move the cursor left or it a character ata lime, or up and down a line at a time. + In menus, move the selection up or down In primary menu choices; left or right through secondary menu choices {such as Symbols or International characters), if available. Function Key ENTER Key + Adds a new blank fine in label data. » Accepts menu selections and attributes.
[on] 2 . ale Be en Caps Lock Key Acts as a toggle to lock text into uppercase as data is entered. Clear Key Clears data from the screen. Decimal Point Adds a decimal point or period.
[on] 2 . Function Keys ee Beebe Feed Key Feeds the media through the printer. Serial Key Sets the start, end, and increment values for serialization. Menu Key Provides printer defaults language, units} and other print options not available on keys. Menu rems include symbols, international characters, bar code styles, and file options. Label Type Kay Accesses the different applications/label type templates installed wire marker, banner, terminal blocks, sic.
[on] 2 . Menus Additional functions not displayed on a key are available from the Menu key. Use the up or down navigation keys to access the different menu items displayed. When you have reached the last menu tier displayed, the menus cycle back w the first menu item. To access the menus: 1. Press MENU. The menu choices display in list. 2. Press the up/down navigation keys to highlight the menu ems. 3. Press Enter Rosette the menu item. To exit a2 menu without selecting i 4.
Data Fields For some menu rems, there may be data fields manifesting additional information. To enter the information: 1. Using navigation keys, navigate to the data field. 2. Enter data using the keyboard. OR Use the left/right navigation keys to goggle through a series of redesigned values. 3. Use navigation keys lo move off the field after entering data. 4.
Printer Defaults Printer defaults are set to provide a consistent operating environment for the work you do with your printer. nce the defaults are set, they will remain in effect until you change therm. The following printer default settings can be found using the Menu key. Language Units Set Clack Cut Mode Set Zero Style Back light Time Language The following languages can be found under the Language menu item. Note: Quick Start Guides are available electronically for all languages listed on the printer.
[on] 2 . Initial Language Setup When turning the printer on for the first time, Immediately go fo the Menu>Language function and choose the language in which you want ali printer menus, functions, and data displayed. 1. Press MENU. 2. Using navigation keys, choose Language. Note: The menu item “Language” is the 6th item in the menu fist and the word “Language” displays in the language that is currently set on your printer.
Clock Format Before sating the date and ime, set the Clock Format. This enables you to use a 12-hour clock or a 24-hour clock. To set the Clock Format: 1. Press MENU. 2. Navigate to Set Cluck, then press Enter oe . 3. Navigate to Clock Format, then press Enter. 4. Select the desired format, then press ENTER. Date Format You have four cholesterol for the date format. The date can be displayed in the American standard {MIDDAY) or the International Standard (DDVMMAYY).
[on] 2 . Time Format Next, choose the Time Format to use. The Time Format displays the time in hours and minutes, or hours, minutes, and seconds, To set the time: 1. Press MENU. 2. Navigate to Set Clock, then press Enter eo . 3. Navigate to Time Format, then press Enter. 4. Select the desired format, then press Enter. Set Date Ones you have set the date and time Format, you can now set the actual date and time. To set the date: 1. Press MENU. 2. Navigate to Set Clock, then press Enter eo . 3.
[on] 2 . Set Time To set the teems: 1. Press MENU. Navigate to Set Clock, then press Enter o . Navigate to Time, then press Enter. Navigate to various fields fo set the hour landlord minutes of the desired time. Note: When using the time format no field for seconds displays. The internal clock in the printer starts the seconds based on the minutes you have chosen. 5. Infer the tme from the keyboard OR use the rightist navigation key to decrease or increase the time, one hour or minute at a time.
Units The Units setting is used to configure label parameters for the printer. The units are: « Inches « Milometers Once configured, you do not have fo indicate “inches” or “millimeters” {or their globally accepted abbreviations or marks} when entering numbers in data fields. Likewise, in any scale or range of measurement field (as found under Label Type], the range of measurements will automatically configure to the units selected in the Menu function. To set the default units: 1. Press MENU. 2.
Cut Mode Set the Cut Mode default to determine when the printer should pause for cutting. There are two modes to choose from: » Cul Between Labels > Talented of Job in a multi print job (serialized label, terminal block, breaker box, sic.) cut mode determines if the printer should pause between each label for cutting the individual labels.
[on] 2 . Set Zero Style The Set Zero Style default determines if the number zero will print as an open zero Oy, or intersected by a ine as on a computer. To set the Zero Style defaults 1. Press MENU. 2. Navigate to Set Zero Style, then press Enter 0 . 3. Navigate to the desired zero style, then press Enter.
Back light Time The Back light Time less the back light auto-off me-oul. This refers fo the number of seconds of inactivity detected, after which the back light automatically shuts off. if you prefer © keep the back light on at all times while using the AG adapter, choose Always On. To tun it off completely, select Always Of. Otherwise set the number of seconds of inactivity the printer should detect before shutting off the back light. The options run from § seconds to 30 seconds, at second intervals.
About About identifies the printer type and the version of firmware installed. 1. Press MENU. 2.
BRADY 2 Getting Started This section describes the process of creating a text label with minimal formatting, using basic editing techniques, and printing the label Entering Text Before entering label text, be sure the media cartridge is based and the power is ON. The vertical bar on the display screen is the cursor and Is the starting point for every label you create. Begin entering text at the position of the cursor. The cursor moves across the screen as you enter data.
Deleting Text To remove characters, one at a time, from the position of the cursor TO THE LEFT (backwards): Press Backspace if you want to delete characters in the middies of the line of text, use the navigation keys to position the cursor to the right of the characters you want to delete, then press [BACKSPACE]L Clear Data The Clear key Is used to dear ali data from the screen.
Font Size Note: This printer provides a single typeface — the Brady Fixed Width Condensed typeface — that has different sizes and weights. Font size can be applied before or after data is entered, regardless of where the cursor is positioned. The font setting applies to all text on the label. You cannot change font size on individual lines of text. The following font sizes are available: Auto Auto Bold 6 & Bold 8 ¢ Bold 14 44 Bold 20 20 Bold 28 28 Bold 40 40 Bold To change the font size: 1. Press FONT SIZE.
Printing a Label To print & label 1. Press PRINT. A printing icon displays on the screen indicating that the label is printing and displays the amount of media left in the cartridge. When the icon disappears, you can out the label. 2. Squeeze the cutter levers to cut the label. Label exit chute eg Cutter levers The label exit chute contains plastic grips that hold the label in place after cutting so it will not fall off. 3. Gently pull the label away from the label exit chute.
[on] 2 . 3 Formatting Formatting refers to the layout, structure, and appearance of a label. Different formatting features can be found under the Menu and function keys. Symbols Symbols {graphics that can be used for a variety of applications are available on the printer. The number of symbols is printer dependent as outlined below: «M210 = 184 symbols «M210 with Cyrillic keyboard = 218 symbols + M210-LAB = 131 symbols To add a symbol to the able 1.
[on] 2 . You can also choose symbols through the Menu function. Press MENU. Navigate to Symbols, then press Enter oO Navigate to the desired symbol category, then press Enter. Using navigation keys, select the desired symbol, then press Enter. The symbol displays with the same font size that is currently in use. Remove a Symbol The symbol is the same as any other character. To remove a symbol 1. 2. Press Backspace Position the cursor to the right of the symbol.
[on] 2 . international Character Set The international Character Sef supplies characters specific fo some international alphabets with diacritical and accent marks incorporated into the characters. To add a character from the International Character Set 1. Post ion the cursor where you want the international character fo display. Press International key -—m OR Crass MENU | Navigate to International, then press Enter o 2. Navigate to the desired international character, then press Enter.
Date and Time To have the current date and/or ime inserted on a label: 1. Z. 3. Position the cursor on the label where you want the date landlord time to be inserted. Press ADD ox JEEP 10 display the date. OR Press ADD TIME wis i display the time. The printer inserts the Date or Time using the current system clock value at the time of printing and the teatime format defined in the Menu function. {For more information, see "Set Clock” settings ony page 3.
[on] 2 Bar code The printer supports Code 39 and Code 128 bar code symbology. You can use either Banner Landscape or Flag labs! type to insert a bar code. {See page 50 for information on changing the Label Type.} Bar code data can be displayed in the same ine as other data (text or symbols). Bar code data on the same line as ext will not overwrite the ext already on the fine but will be placed extinction it. Note: You cannot change the characteristics of the bar code except the font size.
if you want ko enter more data on the same line of text as the bar code: 1. Press the right navigation key to move off the bar code. 2. Enter the data. (Be sure to press Space before entering more data if you want to separate the data from the barhopped) ssc [IMAM ose 123 Bar code In fine of data Printed label of bar code in line of data Edit Bar code Data To audit bar code data: 1. Using the left or right navigation keys, position the cursor in the bar code text. 2.
3. Use the arrows fo scroll fo the desired code (Data matrix or QR) and size (small or large) and press Enter eo ” Data matrix fine of data Small Data matrix Large Datamation QR line of data Small OR Large OR 4. Enter data for the code. Use the left and right navigation keys to move within the data which is shown inside a box. 5. Press the right navigation key to move off the bar code [outside of the box) and stop adding data to the code.
[on] 2 Serialization Serialization {or sequencing) automatically adds a series of sequential numbers or letters to the printed labels. The Serial function consecutively places the next number or letter in the defined sequence on individual labels. The number of labels created is defined by the sequence values you enter. Serialization can be combined with other data on a label. Any data displayed on a labs! that includes serialization will be repeated on every label along with the serial data.
in the above example, the increment value of 2 is added to each previous sequence number. Therefore, +2 =8. cannot add 2 fo sequence number 9 because that would produce sequence number 11, which is higher than the end value of 10. Note: The M210 Label Printer can only process simple serializations, as in the above two examples. it can also process serializations using single or multiple letters. Using Letters in Serialization Sequencing letters occurs according to the letter's position in the alphabet.
[on] 2 . Edith Sequence Add Serialization To add serialization to infidels: 1. Position the cursor on the label where you want the serialization tw display. 2. Press serial ERIE + Dialog box displays where you car enter the start value of the serialization, the increment value, and the end value. For simple serialization: 3. With the cursor immediately displayed in the Start fled, enter the start value of the sequence. 4. in the Increment field, enter the increment value. 5. in the End.
BRADY 4 File Management A label can be saved as a file, fo be opened and reused at a later date. You can save up to 12 files. The files are retained and are not lost when removing the batteries. Note: The printer CANNOT be connected fo a PC. forefathers you cannot print PC label files on the printer. File Naming Standards Tu create a file the file must be given a name. Names can characters long and can consist of letters, numbers, and spaces.
[on] the Fife Name? field, enter a name for the file, then press Enter. When the file is saved, you are resumed to the Editing screen with the saved file still displayed. To remove the saved file from the screen: 8. press crier WERE Replace (Overwrite) a File You narc only save 12 files on the printer. To save another file, you need to replace {overwrite} one of the previously saved files. To replace, or overwrite, a file: Crass MENU. Navigate to File, then press enc GB) Navigate to Save, then press Enter.
[on] 2 . Open a File To open (recall) a saved file: 1. Press MENU. 2. Navigate to File, then press Enter e 3. Navigate to Open, then press Enter. A list of previously saved files displays. 4. Navigate to the file to open, then press Enter. Only one file can be displayed on the screen at a time. When opening a saved file, if the Editing screen contains data, the opened file overwrites that data. If the previous data on the screen was not saved, that data is lost.
Delete a File The display screen does not have to be cleared before deleting a file. A file can be deleted with other data steel on the screen. To delete a previously saved file: 1. Press MENU. 2. Navigate to File, then press Enter So 3. Navigate to Delete, then press Enter. A list of previously saved files displays. 4. Navigate to the file to delete, then press Enter. Delete confirmation message displays. 5.
BRADY 5 Label Types Label types provide templates that guide and control the layout for label formats and may require specific media. The able types available are: M210 and Belorussian Label Printer The M210-LAB Label Printer » Banner Portrait « Banner Landscape » Fixed Length « Custom Length » Vial « Wirehair » Terminal Block « Patch Panel » Panel-Residential « Flag » Breaker Box The printer is intended for laboratory environments and therefore contains only the following label types.
Banner Portrait Label Type Banner Portrait beeline type is used for creating basic labels, with no specific formatting. Banner portrait supports all media except Self lam and Supermassive. When you are using a specific label type, clearing the data removes the data you entered but the specific label type parameters remain. To exit out of the specific label type and return to the general editing mode of the Label Printer, select the Banner Portrait label type. 1. Press LABEL TYPE. 2.
Banner Landscape Label Type Banner Landscape label type allows vou fo enter a lung text string. Any media can be installed for Banner Landscape. If a label type is not supported for newly installed media, the label type automatically switches to Banner Landscape. To print & dong text string (Le. producing a “banners 1. Press LABEL TYPE. 2. Using navigation keys, choose Banner Landscape, then press Enter oS 3. Using navigation keys, choose Horizontal Text or Vertical Text, then press Enter.
Fixed Length if the label type is set to Banner landscape the label length will be as long as necessary to accommodate the font size and text entered. However, you can set the length of the media to a fixed length, which may restrict how much data you can enter on the label. Note: On all infidels, there exists a fixed margin that measures the distance between the edge of the print head and the cutter blade. This distance cannot be changed. To set a fixed label length: 1. Press LABEL TYPE. 2.
Custom Length Setting a custom length gives you the option to set smaller label lengths than what is available with the fixed length setting. The maximum length is 98.9 inches (2537 48mm) with the maximum number of characters at 50. Text will be centered on the label, regardless of length. To set a custom label length: 1. Press LABEL TYPE. 2. Navigate to Custom Length, and press Enter Se 3. Use the number keys to enter the desired length, and press Enter. Enter data as usual.
Vial The Vial label type can be used with any media except Flimflam or Supermassive. (if Flimflam or Supermassive media is installed, the Vial label type does not display.) The Vial label type fixes the length of the label based on the vial size selected and formats the data horizontally or vertically. To get the most data in a small area iris recommended to use a 2D bar code. Tu create a label using the Vial label type: 1. Press LABEL TYPE. 2. Navigate to Vial, then press Enter oS 3.
Wire Marker Label Type (M210) The Wire Marker label type is designed to repeat entered data down the length of the label. The data repeats as many times ag possible, considering the font size and the wire size selected. Bea BEGIN BEGIN SEG] BEG a Wirehair labs! type text on screen Wire Marker label ype printed text All media, except Supermassive, support Wire Marker label types. To use the Wire barker label type: 1. Press LABEL TYPE. 2. Using navigation keys, choose Winemaker, then press Enter e 3.
BEGIN END BEGIN END BEGIN END: BEGIN MIDDLE ENE BEGIN MIDDLE END Wire Marker label type multiple fines as displayed on screen Wire Marker label type multiple fines as displayed on print out User Manual 57
[on] 2 Terminal Block, Patch Panel (M210) Terminal Block and Patch Panel label types are designed to be used with any media, except Self Lam or Supermassive. If Self Lam or Supermassive is installed, these label types are not available. To use Terminal Block or Patch Panel 1. Press LABEL TYPE. 2. Navigate to the desired label type and press Enter eo Data fields display requesting additional information. {For a review of data fled navigation, ses page 21.
[on] T9923 Landscape printout rotation 0° Portrait printout rotation 20° 7. When finished, press Enter. Note: If serialization was muted OFF, proceed to Step 15. if serialization was muted ON, you are presented with the Medal screen. Continue with the following: B. With the cursor displayed In the Start field, enter the start value of the sequence. 9. in the Increment field. enter the increment value. The default increment is 1. If that is the desired increment, skip this entry field. 10.
[on] 2 . To cancel the deletion: 14. Press Backspace RE. again, Note: If serialization was turned OFF, the number of terminals (or ports} display in individual areas. The terminal areas display in the upper right comer of the editing screen. Terminal Block editing screen Pals Panel editing screen Serialization warned CFF Serialization muted OFF 15. Use the up and down navigation keys to navigate to the first numbered data field and enter the identifying information for they terminal. 16.
Panel Residential (M210) Allows you lo create labels for residential breaker box planeload using per-defined or user-defined terms. Labels print portrait if more than one line is used. For the best fit on a standard residential breaker box use font size © on 0.25 inch (8.35mm) width media. All labels are printed left justified with the same fixed width and accept up to 15 characters maximum.
5. {Optional} Navigate to Cut Between, use the right or left navigation key to toggle between YES or NG, then press Enter. Choosing “YES” on Cut Between will prompt you to “Cut” or "Press Print” after each label during printing. Note: Even if the printer is already set to cut between made, it still needs to be selected here. Note: Lis not possible fo return to the set-up menu after leaving it. To exit the application from the Sat-up menu, press STN 8.
Flags (M210) A Flag label wraps around a wire or cable, with the ends joined together to form a flag. The Flag label type is designed to work with any media except Self Lam or Supermassive. To use a Flay able type: 1. Press LABEL TYPE. 2. Navigate to Flag end press Enter a Data fields display requesting additional information. START Fragile Fig Flog gin Diarist (wraps auxin cable} Flag data fields Flag label on print out 3.
5. in the She: field, use the left or right navigation key fo display the eight different flag rotations. iE A Bia slg A Ee Ai lAE LEY 8. When finished, press Enter. Rotation is embedded in the template design, based on the flag design you pick. Justification defaults to center, middies. The font size remains whatever size is set when the flag label type is chosen.
[on] 2 . Breaker Box (M210) Breakers are usually arranged in two columns or along one row, depending on geographic regions. The breaker positions are numbered left-to-right or top-to-bottom, depending on label orientation. This numbering system is universal across various competing manufacturers of breaker panels. To create Breaker Box labels: 1. Press LABEL TYPE. 2. Navigate to Breaker Box, then press Enter Oo 3. in the Spacing: field, enter the width of a standard breaker. 4.
[on] 2 . On the Breaker Box editing screen, enter the number of poles for each breaker and the corresponding identifying data. The number of the breaker displays in the upper right corner of the editing screen. 8. Using the up and down navigation keys, navigate to the breaker number. 8. When on the breaker number, use the left or right navigation keys to toggle fo another breaker number. Breaker field accessed Pole field accessed 10.
BRADY 6 Troubleshooting Use the following table to troubleshoot and diagnose possible performance problems with your Label Printer. If the corrective action suggested does not work, contact Brady's Technical Support Group {see page 67). Problem = Saki ee Hardware Keyboard works intermittently or | One or more keys is stuck in identify any keys stuck in down not at all. depressed state. position. Repress key to UN-stick.
[on] 2 . ey Printer jammed, cannot feed labels en Label exit chute is blocked causing label material to back up inside printer Ble nt ey To clear the jam inside the printer « Slide the locking lever to the unlock position. Note: Unlocking retracts the platen so the cartridge can be removed. If there is a large jam, you may have to force the locking lever to the unlock position.) + Remove the cartridge. « Use tweezers or a deadline-nose pliers to clear label jam.
[on] Power NOMINEE © Banter not working Ble nt ey Printer does not power up when turned on. Battery pack is not charged. # using batteries, replace with 8 new AA batteries. OR, if using the lithium ion battery, remove the battery from the printer Daryl recharge using the AC adapter. Tex use the printer while charging the lithium ion battery, insert 6 AA alkaline batteries in the battery compartment. Screen freezes User interface error. +» Crass Power button to turn the printer off.
ey Printer frequently powers OFF. en Battery is low. Ble nt ey Note: The printer is programmed to shut off automatically after 10 minutes of inactivity. install 6 fresh AA batteries. OR Attach the AC Adapter to the printer Daryl plug info an electrical outlet. This wilt supply immediate power. # using the lithium jon bakery, remove the battery from the printer and recharge using the AC adapter.
[on] 2 . Problem Print Quality en Ble nt ey Door print quality Battery pack, or 6 AA batteries, may be worn out and not proper holding a charge. Battery life is approximately one lo three years, depending on its use and care. Order a replacement battery pack or insert 8 new AA batteries. Poor print quality. Dust or adhesives accumulated on the print head. Clean the print head. (Refer to page 75 for instructions on cleaning the printer) Door print quality Media not usable. Try another media cartridge.
ey Labels en Ble nt ey Printer will not feed labels. The leading edge of the label roll is uneven or form (not a straight edge}. Locking lever not engaged. Use a pair of scissors fo cut a straight leading edge on the label roll. Verify the locking lever is in the parterre position. Press Print but nothing feeds out Locking lever not engaged. Damaged label cartridge. Exit chute jammed. Verify the locking lever is in the correct position. insert a different label cartridge.
ey Program en Ble nt ey invalid terminal repeat value entered, The value entered is out of the range. The acceptable range is between the minimum of 4.2 inch (50.8mm} to the maximum of 40 inches {108mm}. Error "Cannot Fit’ Fort size and settings too large for label. « Change the font size to a smaller font. {See page 34.) « Delete some text. (See page 33) Error “Cannot Fit’ There are too many lines of text. The maximum number of lines slowed is four, but may be less when using per-sized labels.
ey Menu does not display all label types. en The only displays the label types that will work with the installed label material {cartridge). Fewer label types are supported when using per-sized cartridges. Ble nt ey Insert the proper label material (cartridge) for the labels you want to produce. Examples: + using Nylon, Vinyl or Polyester continuous labels, ail labels types will be shown, « if using Self-Lam labels the only label types displayed are Banner Landscape, Fixed Length and Wire.
Cleaning the Printer Cleaning the printer will improve print quality and legibility. It also increases cutout, machine life, printer reliability and performance. Display Screen 1. Lightly moisten a doff cloth with prophylaxis alcohol, 2. Gently wipe the display screen until clean. internal Components internal components that require cleaning are the print head, platen roller and sensor. 1. Turn the printer off. 2. Open the printer cover and remove any cartridge currently in the printer.
#2 BRADY A Symbols Symbols for all enabled applications are available for use on any label, regardless of the application/label type In use.
Greek rosin of printer.
[on] 2 Lab ¥ a symbol cannot print in 6 pt fount the "Cannot FI error message will display. Change font size 19 pl. Some symbols will display the editor.
[on] 2 BRADY C Regulatory Compliance Agency Compliance and Approvals United States Note This equipment has been tested arid found © comply with the miffs for a Class B digital device, pursuant fu part 15 of the FOC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
in accordance with the European WERE Directive, this device needs tube = Waste Electrical and Electronic Equipment Directive recycled in accordance with local regulations. WR R Ohs Directive 2011/65/EU, 2015/863/EU This product is CE marked and complies with the European Union's Directive 201 1/85/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
