• I.D.
Features and capabilities • The I.D. Pro Plus is a highly portable self contained printing machine. • The I.D. Pro Plus uses three different material widths and can print on a variety of materials (i.e..paper, polyester, vinyl cloth, self-laminating vinyl, nylon cloth, Tedlar ? , polyimide, and heat shrinkable materials). • • • The I.D. Pro Plus allows printing up to eight lines of print and 15 characters on each line. It has three format settings and two font sizes.
Features BMXC LS2000 ID PRO PLUS Alignment, vertical & horizontal alignment of te xt No Yes Yes (vertical) Backing material out of unit No Power reverse Yes Bar code printing No No No Battery, N-Cad battery pack Yes Yes Yes Battery, plug-in type battery connector Yes Yes Yes Bold print No Yes Yes Built-in carrying handle No Yes No Case, durable injection mold No Yes Yes Case, hard carrying Included Optional Optional Case, soft Carrying N/A Optional N/A Case, upper
Small = 12 CPI, .09375"H Large = 8 CPI, .125"H Formats Strip - used when printing on Brady Strip series labels such that contain two or more butt cut pieces. Your text will show only once on the screen but will be duplicate the text to the number of strips indicated when printing. Center - automatically centers the text vertically to the total number of lines entered. Wire/Repeat - repeats the text entered for the entire length of the label. Keyboard Clear - clears all characters from the screen .
Bold printing is supported in both large and small font modes. To toggle the bold setting on or off: 1. Press the Shift-O key combination. 2. Press the Up arrow key to toggle bold printing on or off. 3. Press the Enter key to exit. Batch serialization To print a batch of serialized labels: 1. Position the cursor over the right-most character of the desired field, i.e. the number 8 in 99998. 2. Press the Shift-Serial key combination. 3. Enter a number from 1 to 99. 4.
To print 8 stip markers in pairs of 2 numbered from 0000 to 0003. 1. Enter “0000" in the left hand marker display field. 2. Enter “0001" in the right hand marker display field. 3. Press the Shift-Serial key combination. 4. Enter the number “2". 5. Press the Shift-Print key combination. 6. Enter the number “2". 7. Press the Enter or Print key to start printing. 8. The result will be 4 pairs of strip markers numbered 0000 to 0003. Refer to Figure 1B below.
Tutorial • Install the battery and charge it for 4-5 hours. Select the corresponding material guide setting to match the width of the label you are using (i.e. ½", 1", or 1-1/2). • Insert the labels onto the roll holder and place in the label holding area. • Turn the unit on and with the arrow keys select the appropriate size code. This information can be obtained from the inside of the label core and on the outside of the box. • Insert the labels into the material guides and press the feed key.
Cleaning and maintenance • • • • • Turn the unit off. Remove the labels and the bottom door. With a cotton swab and isopropyl alcohol clean the drive roller and the material guide nip roller. Drive roller cleaning - Turn the unit on. From the back of the unit run the cotton swab over the drive roller press ant Feed button (this will rotate the roller). Move the material guides to access all of the drive rollers. Continue this until the roller is clean.
• Ribbon installation - Hold the ribbon cartridge over the ribbon compartment with the exposed ribbon facing toward you. Tilt the left side of the cartridge down and position the ribbon along the left side of the printer. Gently move the ribbon cartridge down and press it into the ribbon compartment until you hear it click into place. Be sure that the ribbon is next to the edge of the printhead as shown on the inside of the roll door. Tighten the ribbon by advancing the turn knob in a clockwise directions.
Ribbon Pocket guide Charger User manual Q. What if the customer wants to print more than one of the same legend? A. Press the SHIFT key and the PRINT key at the same time, enter the number of labels needed, press PRINT. Q. Are there colored ribbons available for the I.D. PRO Plus? A. Only black ribbons are available. Q. What items are excluded from the I.D. PRO Plus? A. Electronic component labels (ECL); Terminal block markers (e.g. TB03); Rollform cable markers (both WRCM B637 and B330); Brady Tags (i.e.
Q. How is multiple serialization done? A. 1. Press the SHIFT-SERIAL key combination. 2. Enter a number from 1 to 99. 3. Press the SHIFT-PRINT key combination. 4. Enter a number from 1 to 99. 5. Press ENTER or PRINT to print or press CLEAR to cancel. More Troubleshooting Labels are not advancing a. Remove any stuck label that may be in the material path and clean the unit. b. Labels are not inserted into the material guides correctly. c. Drive roller platen, mask, or nip rollers are dirty. Clean. d.
