User Manual
Table Of Contents
- Getting Started
- Formatting
- Font
- 1. Press Font .
- 2. Choose Size>font size desired.
- 1. Choose Custom and enter the font size.
- 1. Hold the [Shift] key and press the Up/Down navigation keys enough times to reach the desired font size.
- 1. Position the cursor where the attribute should take affect.
- 2. Press Font .
- 3. Choose the desired attribute, then choose ON.
- 5. Enter the text to be affected by the attribute.
- 1. Press Font .
- 2. Choose the attribute, then choose OFF.
- 2. Press Font .
- 3. Choose the attribute, then choose ON.
- 3. Choose the attribute, then choose OFF.
- 1. Position the cursor where Expand or Condense should take affect.
- 3. Choose Exp/Cond>percentage desired.
- 2. Press Font .
- 3. Choose Exp/Cond>percentage desired.
- Superscript/Subscript
- Symbols
- Date and Time
- Font
- Labels and Areas
- Serialization
- How Serialization Works
- Examples of Serialization
- Add Serialization
- 1. Position the cursor on the label where you want the serialization to display.
- 3. With the cursor immediately displayed in the Start Value field of Sequence #1, enter the start value of the sequence.
- 4. In the End Value field, enter the end value of the sequence.
- 5. In the Increment field, enter the increment value.
- 7. Complete Steps 1 through 6 above.
- 8. On the Editing screen, navigate to the next sequence location (cursor position) on the label.
- 9. Press Serial .
- 11. In the Sequence #2 Start Value field, enter the start value for that sequence.
- 12. In the Sequence #2 End Value field, enter the end value for that sequence.
- 13. In the Sequence #2 Increment field, enter the increment for that sequence.
- 14. Navigate to the Linked option box and press Enter .
- Edit a Sequence
- File Management
- Printing
- 1. Press Print .
- 2. Push the cutter lever down as far as it will go.
- 3. Gently pull the label from the rollers.
- Cancel a Print Job
- Print Preview
- Multi-Print
- 1. Press Multi-Print .
- 2. With the cursor in the No. of Copies field, enter the number of copies desired.
- 3. Navigate to the Collate option box and press Enter to remove the checkmark.
- 4. Navigate to the From field, under Print Range, and enter the number of the first label to be printed.
- 5. Navigate to the To field, under Print Range, and enter the number of the last label to be printed.
- 1. Navigate to the Mirrored Print option box and press Enter to place a checkmark in the field.
- 2. When finished with desired options, navigate to and press Enter .
- Label Types
- General Label Type
- WireMarker
- Terminal Block, Patch Panel, 66 Block
- 1. Press Label Type .
- 2. Navigate to the desired label type and press Enter .
- 4. Navigate to the Separator field and, from the drop down list, select the separator to use.
- 5. Navigate to the Orientation field and, from the drop down list, select the desired layout.
- 6. Navigate to the Terminal Repeat field and indicate the size of the gap between each terminal (with a minimum of 0.2 inches).
- 7. In the Number of Terminals field, enter the number of terminals on the block for which the label is intended.
- 9. Complete the Serialization values. (See “Add Serialization” on page 68 for more information.)
- Flags
- 1. Press Label Type .
- 2. Choose Flags and press Enter .
- 3. Navigate to the radio button of the desired layout and press Enter .
- 4. If continuous media is installed, navigate to the Flag Length field and enter the length of the flag (the part that contains the text).
- 5. Navigate to the Cable Diameter field and enter the diameter of the wire/cable to which the flag will be applied.
- 110-Block, Bix Block Label Type
- 1. Press Label Type .
- 2. Navigate to 110-Block or Bix block and press Enter .
- 3. In the Block Type field, from the drop down list, choose the pair configuration to use.
- 4. In the Sequence Type field, from the drop down list, select the Sequence Type to use.
- 5. In the Start Value field (except when “None” is selected in the Sequence Type field), enter the first number of the sequence.
- 6. In the # of Strips field, enter the number of strips (labels) to be created in the block configuration chosen.
- Vial
- DesiStrip
- Appendix A - Symbols