Installation manual

ManualsBrandsBradley ManualsDomestic AppliancesSS-2/IR/STD

IMPORTANT

Read this entire installation manual to

ensure proper installation.

Flush all the water supply lines before

making connections.

Wall anchors used must have a minimum

pull-out rating of 1,000 lbs.

File these instructions with the owner or

maintenance department.

Product warranties may be found under

"Product Information" on our web site at

www.bradleycorp.com.

SS-2N/IR/STD

SS-2N/IR/WH

Express® Lavatory

System SS-Series

(Standard and Wall-Hung Pedestals)

Express® Lavatory Systems

are ADA and TAS compliant.

U.S. Patent Nos. 5,611,093, D447,224

Other Patents Pending

Installation

Instructions

215-1497 Rev. B; EN 03-808A

Page 1 of 20 4/16/04

Table of Contents

Pre-Installation Information . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . 5-11

Cleaning and Maintenance . . . . . . . . . . .12

Soap Dispenser Maintenance . . . . . .13-14

Assembly of Components . . . . . . . . .15-16

Solenoid Valve Troubleshooting . . . .17-18

Vernatherm™ Mixing Valve . . . . . .19-20

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY FAX: (262) 251-5817

http://www.bradleycorp.com

SS-2N/IR/STD

SS-2N/IR/WH

Summary of content (20 pages)

PAGE 1
Installation Instructions SS-2N/IR/STD SS-2N/IR/WH Express® Lavatory System SS-Series (Standard and Wall-Hung Pedestals) D A CO M Express® Lavatory Systems are ADA and TAS compliant. A SS-2N/IR/STD PL IA NT U.S. Patent Nos. 5,611,093, D447,224 Other Patents Pending Table of Contents SS-2N/IR/WH Pre-Installation Information . . . . . . . . . . .2 Dimensions . . . . . . . . . . . . . . . . . . . . . .3-4 Installation Instructions . . . . . . . . . . . 5-11 Cleaning and Maintenance . . . . . . . . .
PAGE 2
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Pre-Installation Information Barrier-free and ADA compliant - standard height mounting The SS-2N/IR Express® Lavatory System must have a rim height of 34" above finished floor to be compliant with Americans with Disabilities Act (ADA). When mounted at 34" rim height, the Express® meets ADA, ANSI and UFAS requirements for barrier-free clearances, reaches and controls.
PAGE 3
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions SS-2N/IR/STD and SS-2N/IR/WH Express® Lavatory System Dimensions 50" (1270mm) 8-5/8" (219mm) 15" (381MM) 15" (381MM) 8" (203mm) RADIUS 10" (254mm) RADIUS 38-1/4" (972mm) 7" (178mm) 21-1/4" (540mm) 30" (762mm) 36" (914mm) 38-1/4" (972mm) 7" (178mm) 30" (762mm) 36" (914mm) Bradley Corporation • 215-1497 Rev.
PAGE 4
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Express® Lavatory System Dimensions continued . . .
PAGE 5
Installation Instructions Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Step 1: Rough in IMPORTANT: Flush the supply lines before making connections. Debris in supply lines will cause the valves to malfunction. IMPORTANT: Dimensions shown in Figure 1 on page 6 are for a Standard and WallHung Pedestal Express® only. Make sure to follow appropriate dimensions based on configuration and required rim height. See Charts 1 and 2 on page 6 before beginning rough-ins. 1.
PAGE 6
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions SS-2N/IR Express® Lavatory System Dimensions CL 23-1/2" (597mm) 23-1/2" (597mm) 13-1/4" (337mm) OPTION #1* 9-3/8" (238mm) A COLD SUPPLY 9-3/8" (238mm) 3" (76mm) B OPTION #2** D B D 4" (102mm) F A 4" (102mm) E TEMPERED SUPPLY OPTION 32" (813mm) 28-3/4" (730mm) B B 25-3/4" (654mm) 2" (51mm) 20" (508mm) 19" (483mm) 13" (330mm) 22" (559mm) 15" (381mm) C C FLOOR 3-1/2" (89mm) * OPTION 1 - RECO
PAGE 7
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Installation Instructions continued . . . Step 2: Mounting frame to wall 1. Using a T20 Torx key, remove the six #10-24 flat head Torx screws and #10 finish washers securing the access panel to the main frame, and remove the panel (see Figure 2). 2. Position the main frame against the wall, ensuring that it is level.
PAGE 8
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Installation Instructions continued . . . Step 3: Installing bowl assembly WARNING: To prevent serious injury and/or damage to the bowl, move and position the bowl with the assistance of another person and always use appropriate lifting procedures. NOTE: Refer to Figure 4 below when installing the bowl assembly. NOTE: The sprayhead body has slotted holes for adjusting the fit-up with the bowl and wall. 1.
PAGE 9
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Installation Instructions continued . . . Step 4: Connecting supply and drain 1. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the valve bracket up until the larger cutout in the frame’s slot aligns with the screw head (see Figure 5c). Then lift up to remove the valve bracket from the frame. 2.
PAGE 10
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Installation Instructions continued . . . Step 5: Connecting optional hot water heater NOTE: 240/208 or 277 voltage is required for hot water heater. Refer to the installation manual provided with BRACKET the hot water heater for further installation information. 1. Remove the cover from the water heater.
PAGE 11
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Installation Instructions continued . . . Step 6: Connecting electrical and supply tubing WARNING: The Express® must be connected to the 24 VAC Class II plug-in transformer provided. Connection to 110 VAC can result in damage to the electronics and cause personal injury. CAUTION: Connection of leads other than shown may cause permanent damage to the sensor. 1.
PAGE 12
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Cleaning and Maintenance Instructions IMPORTANT: Strong alkaline or acid-based chemicals and cleansers should not be used to clean Terreon®. If these chemicals come in contact with the Terreon® surface, wipe off the surface immediately and flush with soapy water.
PAGE 13
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Soap Dispenser Maintenance Step 1: Fill soap dispenser The soap valve will dispense vegetable/coconut oil liquid soaps, synthetic detergents, viscous lotion soaps, and antiseptic solutions. A 10-15% concentration is recommended for vegetable or coconut oil liquid soaps. Synthetic detergents, lotion soaps, and antiseptic soaps require no dilution. 1.
PAGE 14
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Soap Dispenser Maintenance continued . . . Step 2: Change soap type 1. Pour out all of the soap from the dispenser. 2. Rinse the soap dispenser with hot water several times until all of the residue is removed, and pump the valve until clean water appears. 3. Rinse the dispenser with ethyl alcohol and allow to air dry. 4. After the dispenser is dry, pour the new soap into the soap dispenser.
PAGE 15
Installation Instructions Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Assembly of Components SPRAYHEAD COVER SPRAYHEAD BODY FASTENERS SPRAYHEAD/COVER (4) 160-386 BOWL PANEL FASTENERS (160-450) MAIN FRAME S17-325 WASHERS (142-002CA) (6) PLACES ACCESS PANEL GRAY (186-1455) PUTTY (186-1455A) COAL (186-1455B) SCUFF BASE PANEL GRAY (185-034) PUTTY (185-034A) COAL (185-034B) SCUFF FRAME S17-326 USED WITH STANDARD HEIGHT FRAME ONLY SCUFF PANEL FASTENERS (160-450) WASHERS (142-002CA) (4)
PAGE 16
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Assembly of Components continued . . . Sensor assembly and solenoid valve To access solenoids and sensors: Remove the four Phillips-head screws located in the bottom of the sprayhead body and lift the cover/shelf off (see components illustration on page 15 for locations).
PAGE 17
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Troubleshooting Solenoid Valve (VAC) CAUTION: Problem: Cause: Solution: Turn off water supplies to unit before troubleshooting. An individual operating station fails to shut off and drips. There is debris trapped between the diaphragm and the valve seat. Remove debris between diaphragm and the valve seat. 1. Remove the three #8 Phillips-head screws that hold the solenoid valve assembly together.
PAGE 18
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Solenoid Valve S07-068 (closed body) and S07-068A (thru body) REF. 1 1 2 3 4 5 6 7 8 9 10 8 7 8 QTY. 1 1 1 1 1 1 1 1 3 1 1 PART NO.
PAGE 19
Installation Instructions Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Thermostatic Mixing Valve Maintenance and Troubleshooting NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions: • If stop/check valves are used, make sure that they are fully open. • Make sure that the hot and cold inlet pipes are connected properly, and that there are no crossconnections or leaking stop/check valves.
PAGE 20
Express® Lavatory System SS-Series SS-2N/IR/STD, SS-2N/IR/WH Installation Instructions Vernatherm™ Thermostatic Mixing Valve S01-520 Repair Kit S65-259 Item Qty Description 2 1 Spring 3 1 Piston 4 1 Thermostat 6 1 O-Ring 7 1 O-Ring 10 2 Strainer (173-028) Strainer 9 Nut 3/8-24 Hex Jam 8 Cap 7 O-Ring 6 O-Ring 5 Stem 4 Thermostat 3 Piston 2 Spring 1 Valve Body 10 Strainer 10 Figure 10 20 4/16/04 Bradley Corporation • 215-1497 Rev.