Installation manual

ManualsBrandsBradley ManualsHome building and DecorEXPRESS SS-3/AST/STD

P.O. Box 309, Menomonee Falls, WI 53052-0309

Phone: 1-800-BRADLEY Fax: 262-253-4161

www.bradleycorp.com

Installation

215-1494 Rev. E; ECN 07-814

Page 1 of 14 12/11/07

SS-3N/AST/STD

SS-3N/AST/WH

Express® Lavatory System SS-Series

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . . .2

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Supplies Required . . . . . . . . . . . . . . . . . . . . . . . .4

Dimensions............................... 4–5

Rough-Ins ...................................6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .7–10

Metering Air Valve Troubleshooting . . . . . . . . . .11

Vernatherm Mixing Valve Troubleshooting . . . . .12

Stop/Check Valve Troubleshooting . . . . . . . . . . .13

Cleaning and Maintenance for Terreon® . . . . . .13

Soap Dispenser Maintenance . . . . . . . . . . . . . .14

Express Lavatory Systems are ADA and TAS compliant

SS-3N/AST/STD/LSD-3

SS-3N/AST/WH/LSD-3

•

Summary of content (14 pages)

PAGE 1
Installation A •COM SS-3N/AST/STD/LSD-3 DA SS-3N/AST/STD SS-3N/AST/WH PL IANT Express® Lavatory System SS-Series Express Lavatory Systems are ADA and TAS compliant Table of Contents SS-3N/AST/WH/LSD-3 215-1494 Rev. E; ECN 07-814 © 2007 Bradley Corporation Page 1 of 14 12/11/07 Pre-Installation Information . . . . . . . . . . . . . . . . .2 Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Supplies Required . . . . . . . . . . . . . . . . . . . . . . . .4 Dimensions. . . . . . .
PAGE 2
SS-3N/AST/STD, SS-3N/AST/WH Installation IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Installation Packing List IS TH SIDE UP • • • • Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material.
PAGE 3
Installation SS-3N/AST/STD, SS-3N/AST/WH Components SPRAYHEAD COVER (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE). BOLT 5/16-18 160-371 SCREW 10-24 160-386 SPRAYHEAD BODY (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE). BOWL (PART NUMBER VARIES WITH COLOR OF UNIT. CONTACT YOUR LOCAL BRADLEY REP. FOR ASSISTANCE).
PAGE 4
SS-3N/AST/STD, SS-3N/AST/WH Installation Supplies Required: • (8) 3/8" wall anchors, bolts and 1" min. O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • STD. HEIGHT ONLY: (2) 3/8" wall anchors, bolts and 1" min. O.D.
PAGE 5
Installation SS-3N/AST/STD, SS-3N/AST/WH Dimensions - Side Views 21-1/8" (537mm) 11-1/2" (292mm) STANDARD HEIGHT 34" (864mm) 38-1/2" (978mm) 8-5/8" (219mm) 30" (762mm) 3" (76mm) 13-1/4" (337mm) A D CO M 21-1/8" (537mm) 11-1/2" (292mm) WALL-HUNG MOUNTED AT STANDARD HEIGHT 34" (864mm) IA NT 21-1/8" (537mm) WALL-HUNG MOUNTED AT JUVENILE HEIGHT AGES 6 THROUGH 12 38-1/2" (978mm) 8-5/8" (219mm) 30" (762mm) SCUFF BASE STANDARD HEIGHT ONLY A PL 11-1/2" (292mm) 35-1/2" (902mm) 31" (787mm) 8-5/8
PAGE 6
SS-3N/AST/STD, SS-3N/AST/WH 1 Installation Rough-Ins C L 38-1/2" (978mm) 38-1/2" (978mm) 24-3/8" (619mm) 24-3/8" (619mm) 8" (203mm) 2-3/4" 70mm) 4" (102mm) A, F B G B D1 D2 H A, F B 34" (864mm) E 32" (813mm) B 28-3/4" (720mm) 15" (381mm) B B 24" (610mm) 23" (584mm) 5-5/8" (143mm) 18" (457mm) C RIM HEIGHT SEE CHART BELOW C FLOOR 27-1/2" (699mm) 3-1/2 (89mm) CODE A 6 DESCRIPTION QTY. 3/8" Wall Anchors with a minimum pull-out force of 1,000 lbs.
PAGE 7
Installation 2 SS-3N/AST/STD, SS-3N/AST/WH Mount Frame to Wall Anchoring the frame to a wall that is not flat may cause the frame to bend, making it difficult to reinstall the access panels. If necessary, use shims to compensate for wall distortion. A SCUFF PANEL STANDARD HEIGHT FRAME ONLY Using a T20 torx key, remove the fasteners securing the access panel to the main frame, and remove the panel.
PAGE 8
SS-3N/AST/STD, SS-3N/AST/WH 4a Installation Connect the Supply — Hot and Cold Supply C A 4b The letter “H” on the Vernatherm™ Mixing Valve indicates hot water supply inlet. Connect one end of each hose to the Vernatherm™ valve (one on the hot side, one on the cold side). Connect the other swivel end to the stop/ check valves. Loosen but do not remove the two mounting screws holding the valve bracket to the frame. Slide the valve bracket up and lift it from the frame.
PAGE 9
Installation 5 SS-3N/AST/STD, SS-3N/AST/WH Install the Drains To Drain Stub-Out 6 240/208 or 277 voltage is required for hot water heater. Refer to the installation manual provided with the hot water heater for further installation information. Optional Electric Tankless Water Heater A B Hang the water heater on the right side frame member. Connect the 1/2" flexible hose from the cold water supply stub-out to the hot water heater inlet. Bradley Corporation • 215-1494 Rev.
PAGE 10
SS-3N/AST/STD, SS-3N/AST/WH 7 Installation Connect Supply and Tubing A B C Loosen the compression nuts. Push the sprayhead supply tubes firmly into the tube connectors until they are fully seated. Tighten the compression nuts by hand. Loosen the compression nuts. Push the matching color 1/8" tubes firmly into the tube connectors until they are fully seated. Tighten the compression nuts by hand. Reinstall the valve bracket. Turn on the water supply to the Express® and check for leaks.
PAGE 11
Installation SS-3N/AST/STD, SS-3N/AST/WH Troubleshooting – Metering Air Valve 8 Turn off water supplies to the unit before troubleshooting. 7 5 Item Qty.
PAGE 12
SS-3N/AST/STD, SS-3N/AST/WH Installation Troubleshooting – Vernatherm™ Thermostatic Mixing Valve: Part no. S01-524 Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions: • If stop/check valves are used, make sure that they are fully open. • Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-connections or leaking stop/check valves.
PAGE 13
Installation SS-3N/AST/STD, SS-3N/AST/WH Stop/Check Valve Troubleshooting Problem Cause Solution Water dribbles or does not flow from the sprayhead. Stop/Check Valves may not be functioning properly. 1. Close the stops and inspect the valves that supply water to the lavatory system. 2. Inspect the stop/check valves to see that they have been properly installed. 3. Remove the flexible hoses from the stop/check valves and inspect the strainers. Clean strainers, if necessary.
PAGE 14
SS-3N/AST/STD, SS-3N/AST/WH Installation Fill Soap Dispenser The soap valve will dispense vegetable/coconut oil liquid soaps, synthetic detergents, viscous lotion soaps, and antiseptic solutions. A 10-15% concentration is recommended for vegetable or coconut oil liquid soaps. Before filling, rinse out each soap tank with hot water to remove packing dust. Shake water out thoroughly and allow to dry. DO NOT OVERFILL! Leaf Spring will engage when soap tank is pushed into place.