Spec Sheet
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,682,666; 7,634,976; 5,660,165; 5,954,492; 6,056,542; 6,935,280; 5,372,185; 5,485,879; 5,574,822; 7,971,560; 7,992,526; 6,684,821; 7,334,419;
7,866,168; 7,270,087; 7,007,748; 5,596,952; 6,142,216; 7,699,026; 5,341,770; 7,337,517; 7,665,211; 7,665,210; 7,063,132; 7,063,133; 7,559,293; 7,900,589; 5,943,984; 8,082,888; 5,988,117; 7,621,238; 7,650,859; 5,761,379;
7,409,925; 5,277,171; 8,146,772; 7,458,341; 2,262,174. OTHER U.S. AND FOREIGN PATENT APPLICATIONS PENDING. CURRENT CANADIAN PATENTS: 2,314,845; 2,504,824; 2,108,186; 2,143,031; 2,409,271; 2,548,958; 2,112,515;
2,476,685; 2,239,007; 2,092,105; 2,107,012. Vitraglas
®
and Hydrojet
®
are registered trademarks of Bradford White
®
Corporation.
5-Year Limited Tank Warranties / 1-Year Limited Warranty on Component Parts.
For more information on warranty, please visit www.bradfordwhite.com
For products installed in USA, Canada, and Puerto Rico. Some states do not allow limitations on warranties. See complete
copy of the warranty included with the heater.
C555-F-1221 CANADA
Commercial PowerStor Series
®
Single-Wall Indirect Water Heater
The PowerStor Series
®
Single-Wall Models feature:
n Heat Exchanger—Single-Wall 1
1
⁄2" O.D. glass coated (Vitraglas
®
) carbon
steel coil. The coil has a heat transfer area of 27.2 sq. ft. (2.5m
2
) and a stored
water volume of 5.0 Gal. (19L). Maximum supply temperature from the boiler
must not exceed 240°F (116°C).
n Factory Installed Hydrojet
®
Total Performance System—Sediment
reducing device that also increases first hour delivery of hot water while
minimizing temperature build-up in tank.
n Vitraglas
®
Lining—An exclusively engineered enamel formula that provides
superior tank protection from the highly corrosive effects of hot water. This
formula (Vitraglas
®
) is fused to the steel surface by firing at a temperature of
over 1600°F (871°C).
n Immersed Adjustable Aquastat—Fast acting immersion aquastat for
automatic temperature control.
n Supply and Return Connections—1" (25mm) NPT female connections are
located on the front for both the boiler collector supply and return.
n Insulation System—2" (51mm) Non-CFC foam insulation covers the
sides and top of the tank, reducing heat loss. This results in less energy
consumption, improved efficiencies, and jacket rigidity.
n Potable Water Connections—1" (25mm) NPT factory installed true
dielectric fittings extend water heater life and eases installation.
n Three Protective Aluminum Anode Rods—Provide added protection
against corrosion for long trouble-free service.
n T&P Relief Valve—Installed.
n Low Restriction Brass Drain Valve—Tamper proof design.
n AHRI Certified—These water heaters are rated by the Air-Conditioning,
Heating, and Refrigeration Institute to provide accurate performance
data within the standards of the certification. This certification provides a
recognized standard for proper comparison of hydronic appliances.
Photo is of
SW-80C-5