Spec Sheet
Residential Through-The-Wall
Energy Saver Gas Water Heater
The TTW1 Models Feature:
■ P
ower Vented Heater—
D
esigned for installations where atmospheric
units cannot be used. Exhaust gases are vented under positive
pressure directly out of the building through the roof or the wall.
■ Powerful Blower Motor—Our design has higher torque for greater
resistance to outside winds and the power to eliminate problems with
difficult venting situations. This significantly quieter motor runs cooler
for a considerably longer operational life.
■ Spark-to-Pilot Ignition System—Eliminates the constant burning
pilot used on other water heaters. This device results in savings of
pilot gas during standby periods (110 VAC required to heater).
■ PVC, ABS or CPVC Venting—Horizontal and vertical venting up to
50 equivalent feet for 2" pipe, and up to 120 equivalent feet for 3"
pipe. See reverse side for specifics.
■ Vitraglas
®
Lining—Bradford White water heater tanks are protected
from the corrosive effects of hot water by a ceramic porcelain-like
coating. The exclusive high silica ceramic lining provides a tough
interior surface for our water heater tank.
■ Steel Tank—Heavy gauge steel automatically formed, rolled and
welded to assure a continuous seam for glass lining.
■ Protective Magnesium Rod—Provides added protection against
corrosion for long trouble-free service.
■ Factory installed Hydrojet
®
Total Performance System—Cold inlet
sediment reducing device. Helps prevent sediment build up in tank.
Increases first hour delivery of hot water while minimizing temperature
build up at top of tank.
■ Factory installed Heat Traps—Design incorporates a flexible disk
that reduces heat loss in piping and eliminates the potential for noise
generation.
■ Water Connections—3/4"NPT factory installed true dielectric fittings.
Extends water heater life and eases installation.
■ 1" Non-CFC Foam Insulation—Covers the sides and top of tank to
save energy by retarding loss of heat. Also increases jacket rigidity.
■ Electronic Gas Control Valve—The integrated, immersion gas
control valve offers more precise temperature control for higher first
hour delivery and also allows water temperature adjustment without
removing the cover. The control is equipped with an LED display to
aid in start-up and diagnostics.
■ Brass Drain V
alve
.
■ T&P Relief Valve Included.
■ Stainless Steel Flue Baffle—Designed to maximize the amount of
heat absorbed in the lower portion of tank. Reduces air movement in
the water heater during standby periods to retard heat loss up the
flue.
■ Design Certified by CSA International (formerly AGA and CGA).
MANUF
ACTURED UNDER ONE OR MORE OF THE FOLLOWING U.S. P
A
TENTS:
5,954,492; 5,761,379; 5,943,984; 5,081,696; 5,988,117; 6,142,216; 5,199,385; 5,574,822; 5,372,185; 5,485,879; 5,277,171;
(B1)5,341,770; 5,660,165; 5,596,952; 5,682,666; 4,904,428; 5,023,031; 5,000,893; 4,669,448; 4,829,983; 4,808,356; 5,115,767; 5,092,519; 5,052,346; 4,416,222; 4,628,184; 4,861,968; 4,672,919; Re. 34,534.
OTHER U.S. AND FOREIGN PATENT APPLICATIONS PENDING. CURRENT CANADIAN PATENTS: 1,272,914; 1,280,043; 1,289,832; 2,045,862; 2,112,515; 2,108,186; 2,107,012; 2,092,105.
V
itraglas
®
and Hydr
ojet
®
ar
e registered trademarks of Bradford White
®
Corporation.
©2006, Bradford White Corporation. All rights reserved. Printed in U.S.A.
1000-B 0506
6-Year Limited Warranty on Component Parts / 6 or 10-Year Limited Tank Warranties.
For more information on warranty, please visit www.bradfordwhite.com
For pr
oducts installed in USA, Canada and Puer
to Rico. Some states do not allow limitations on warranties. See complete
copy of the warranty included with the heater.
M-1-TW-40S6BN