Brochure

ManualsBrandsBradford White ManualsGas Controls & ValvesSingle Element Conversion Kit (208v/2000w)

Table Of Contents

Light Duty Commercial Electric

Voltage and Wattage Conversion Instructions

Conversion to be performed by a Qualified Service Person only.

Underwriters Laboratories Inc. recognizes this procedure as herein presented and no

deviation from these instructions are allowed.

LD-20L

LD-30L

LD-30R

LD-40L

LD-40S

LD-50L

LD-50S

LD-65R

LD-80R

LD-120R

LE120L

LE130L

LE230S

LE140L

LE240S

LE150L

LE250S

LE265T

LE280T

LE2120T

LDWH‐6U

LDWH‐12U

LDWH‐20L

LDWH‐30L

LE16WV

LE112WV

LE120WV

LD-6U

LD-12U

LD-12UT

LD-20U

LD-30U

LE16U

LE110U

LE112T

LE115U

LE120U

238‐46411‐00F 4/19

Summary of content (8 pages)

PAGE 1
Light Duty Commercial Electric Voltage and Wattage Conversion Instructions Conversion to be performed by a Qualified Service Person only. Underwriters Laboratories Inc. recognizes this procedure as herein presented and no deviation from these instructions are allowed.
PAGE 2
The conversion procedure outlined in the instruction manual is to be executed only by Qualified Service Personnel. Read these instructions first before proceeding with the conversion. The purpose of this instruction manual is to instruct about the changing of wattage and voltage for Light Duty Commercial Electric water heaters manufactured by Bradford White Corporation. ETL recognizes this procedure as herein presented and no deviation from these instructions are allowed.
PAGE 3
Element(s) Removal: 1. Turn off electrical power to water heater, DISCONNECT FROM POWER SOURCE. Remove screw 2. Drain water heater. 3. Remove element access cover(s). Element access cover 4. Remove Insulation. Remove insulation 5. Remove thermostat(s) protector.
PAGE 4
6. Disconnect wire leads from element(s) terminal block. Element terminal block Disconnect wire leads from element terminal block 7. Remove element(s) from tank using 1½" deep well socket or wrench. Unscrew element(s) counter-clockwise to remove from tank. Unscrew element(s) counter-clockwise to remove from tank Element(s) Installation: 8. Check element terminal block for proper electrical rating. Note: Some elements have a dual rating, so be sure to check all surfaces on element terminal block.
PAGE 5
9. Apply new gasket(s) to new element(s) from conversion kit. Note: Make sure gasket is seated flat against element flange without rolls or gaps. Gasket 10. Thread new element(s) clockwise into tank. Tighten element(s) with a 1 ½" deep well socket or wrench. Do not over tighten. Over-tightening may damage gasket. Note: Clean any debris from element(s) fitting to tank. Lubricate element(s) threads as needed with thread lubricant. Element flange 11. Be sure tank is filled with water and check for leaks. 12.
PAGE 6
NOTES Page 6 of 8
PAGE 7
NOTES Page 7 of 8
PAGE 8
Ambler, PA For U.S. and Canada field service, Contact your professional installer or local Bradford White representative. Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2180 Technical Support/800-334-3393 Fax/269-795-1089 Warranty/800-531-2111 Fax/269-795-1089 International: Telephone/215-641-9400 Telefax/215-641-9750 Halton Hills, ON Sales & Technical Support /866-690-0961 905-203-0600 Fax/905-636-0666 Email parts@bradfordwhite.com techserv@bradfordwhite.com www.bradfordwhite.