Model# RS700 www.boxisautoshred.
A Revolution in Productivity Our innovative paper feeder mechanism grabs documents one at a time from the middle and shreds them into unreadable microcut particles. The Boxis™ AutoShred™ automates large shred jobs. It only takes seconds to load and start – destroys a full load in approximately 10-12 minutes – you no longer need to stand there while the paper is being shredded.
Table of Contents Warnings......................................................................................................................................2 Specifications...............................................................................................................................3 Installation....................................................................................................................................4 Safety Instructions..........................................
! WARNINGS ! CAUTION: KEEP THIS DEVICE AWAY FROM CHILDREN AND PETS! Place the paper shredder in an area less accessible to children. DO NOT PLACE FINGERS TOO CLOSE TO THE FEED SLOT AS SERIOUS INJURY MAY OCCUR. Paper shredders can pull children’s fingers into the shredder mechanism. AVOID GETTING LOOSE CLOTHING OR JEWELRY NEAR THE FEED SLOT. AVOID GETTING HAIR NEAR THE FEED SLOT. NEVER spray any aerosol-based products in or around the shredder.
The Boxis™ AutoShred™ RS700 Technical Specifications Model....................................................................................................................................RS700 Cutting Style...................................................................................................................Micro-Cut Shred Size.................................................................................................0.1” x 0.7” (3 x 20mm) DIN Security Level.............................
Installation • Refer to set-up instructions printed on carton box for proper assembly. • Only operate this product from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult an electrician. • Make sure the electrical outlet is easily accessible from the shredder. • Shredder must be operated only in upright position. • To make sure the shredder has proper ventilation, place it a minimum distance of 5cm (2 inches) from the wall or furniture.
Diagram Start Button LCD Panel Manual Stop Button Manual Manual Lubricate Forward & Lock & Reset Reverse Unlock Button Buttons Buttons Paper Tray Power Doors Switch Keypad (For security code) Manual Feed Slot Control Panel Handles for Paper Tray Doors Cabinet Access Door Ventilation Handles Manual Unlock (on right side of shredder) Contents inside cabinet: • Waste Bin • Key for Manual Unlock • User Quick Guides • User Manual • Lubrication Sheets • Waste Bin Liners Heavy-Duty Locking Casters 5
Operation Read instructions completely before operating shredder. Connect power cord to the power socket at the backside of the machine. Connect the power cord to any standard 120V AC, 60Hz outlet. Install waste bin • Open cabinet door and remove remove waste bin from the cabinet. • Place plastic waste liner around the basket (2 waste liners included). Allow bag edges to overhang. • Slide the waste bin into the cabinet and shut the cabinet door. • Store this operation manual in slot inside cabinet door.
Operation (cont’d) To manually feed paper (max. 6 sheets) or lubricant sheets. • The shredding process is initiated by photo sensors in the paper feed opening. Insert a maximum of 6 sheets of paper into the paper feed opening; shredding begins automatically. When shredding is complete, the cutting system automatically stops after approximately 3 seconds. • For maintenance, shredder lubricant sheets should be fed in the paper feed opening as well. To clear paper jam.
Operation (cont’d) AUTO Mode • The master power switch is located on the top right side of the cabinet. When switch is toggled ON, the LCD shows AUTO and the machine enters into AUTO mode. • In the AUTO mode, the shredder is ready to shred paper either by auto or manual feed. START Mode • Press the “Start” button and the machine starts shredding paper loaded in paper tray. The LCD shows AUTO with paper feeding. STOP Mode • Press the “Stop” button to interrupt the shred job. The LCD displays flashing STOP.
Locking for Secure Shredding The doors can be locked to avoid confidential papers from being taken out of the paper tray by other people. To LOCK a shred job. • Press “Lock” button. ENTER PASSWORD will flash on LCD. Enter any 4-digit PIN. Be sure to remember the PIN. Press “Enter” button. • COVER UNLOCK will change to COVER LOCK on the LCD. • Both doors will be locked mechanically. The locking process takes approximately 3 seconds.
InfoCenter™ LCD Panel FORWARD Mode • Pressing the “Forward” button during STOP mode will initiate the manual Forward function. Press and hold the “Forward” button in order to keep the motor running in forward. When the “Forward” button is released, the machine returns to STOP mode and the LCD displays flashing STOP. OVERLOAD Mode • If the shredder becomes overloaded during operation, the motor will stop running and sound an alert. The LCD will display OVERLOAD.
InfoCenter™ LCD Panel (cont’d) OVERHEAT Mode • If the shredder overheats, the LCD will show a flashing OVERHEAT icon. All functions will stop. When the shredder overheats, user may press Stop button to place the shredder in Standby mode. The shredder will not resume normal functioning until the temperature of the motor cools down to a safe temperature and LCD shows AUTO. BIN FULL Mode • If the waste bin is full, the motor will stop and sound an alert. LCD shows the character BIN FULL.
Maintenance LUBRICATION • After about one hour of accumulated shredder usage, the LCD will display “LUBRICATE”. This indicates that the shredding blades need to be lubricated using an approved shredder lubricant. Only shredder lubricant sheets or bottled lubricant designed specifically for shredders should be used. Follow the instructions provided with the shredder lubricant. NEVER USE AN AEROSOL LUBRICANT, or any lubricant that is flammable. Refer to the warnings provided in this shredder manual.
Warranty and Product Registration The manufacturer warrants the machine for a limited time to be free from defects in material and workmanship, does NOT include normal wear and tear. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at the manufacturer’s option and expense, of the defective part except for the postage. It is the responsibility of the consumer to return the machine to the manufacturer.
