2-In-1 Stand Assembly Instructions Model: BDS1642
Complete Stand Component Diagram � � �� �� � �� �� � � �� �� �� �� �� �� � �� �� �� � �� � �� �� �� � � �� �� �� 2
Parts Tools Required # Qty. Description 1 1 TUBE, BOTTOM CROSS BRACE 2 1 ASSEMBLY, REAR LEFT STABILIZER 3 1 ASSEMBLY, REAR RIGHT STABILIZER 4 2 ASSY, STAND LEG 5 1 WELDMENT, LEFT DUMBBELL PLATFORM 6 1 WELDMENT, RIGHT DUMBBELL PLATFORM 7 1 WELDMENT, TOWEL BAR 8 1 FOOT PEGS, SET OF FOUR 9 1 HOLD DOWN STRAPS, 2F 2M 10 20 NUT-NL 0.375-16 G2-BlkZ 11 36 WASHER-FLAT 0.375 REGULAR BLKZ 12 8 SCREW-BHCS 0.375-16x3.0 G2-BlkO 13 4 SCREW-BHCS 0.375-16x2.
step 1 � � �� �� �� �� Figure 1 Parts: • Stand Leg (#4) • Rear Left Stabilizer (#2) Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Qty 2 4 2 Tools: • Hex Key (7/32”) 1-1 Attach the Rear Left Stabilizer (#2) to the Stand Leg (#4) using the hardware shown in Figure 1. Note: Do not tighten hardware.
step 2 � �� �� � �� �� Figure 2 Parts: • Stand Leg (#4) • Rear Right Stabilizer (#3) Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Qty 2 4 2 Tools: • Hex Key (7/32”) 2-1 Attach the Rear Right Stabilizer (#3) to the Stand Leg (#4) using the hardware shown in Figure 2. Note: Do not tighten hardware.
step 3 � � �� �� � �� � � Figure 3 Parts: • Cross Brace (#1) • Left Stand Leg assembly from Step 1 • Right Stand Leg assembly from Step 2 Hardware • 3" Screws (#12) • Washers (#11) • Nuts (#10) Qty 4 8 4 Tools: • Hex Key (7/32”) 3-1 Attach the Bottom Cross Brace (#1) to the Rear Left Stabilizer (#2) and Rear Right Stabilizer (#3) using the hardware shown in Figure 3. Make sure that the narrower edge of the Cross Brace (#1) is closer to the Stand Leg (#4) uprights. Note: Do not tighten hardware.
step 4 �� �� �� �� �� �� �� �� �� Figure 4 Parts: • Stand Leg and Cross Brace assembly from Step 3 • Center Plate (#17) Hardware • 2.5" Screws (#14) • Washers (#11) • Nuts (#10) Qty 4 8 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 4-1 Install the Center Plate (#17) to both Stand Legs (#4) using the hardware shown in Figure 4. Note: Make sure that the Center Plate edges are on the outer sides of the legs, and that the logo on the Plate is right side up.
step 5 � �� �� �� �� Figure 5 Parts: • Stand base assembly from Step 4 • Left Dumbbell Platform (#5) Hardware • 2.75" Screws (#13) • Washers (#11) • Nuts (#10) Qty 2 4 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 5-1 Secure the Left Dumbbell Platform (#5) to left Stand Leg (#4) using the hardware shown in Figure 5. Note: Make sure the screw holes in the Platform are toward the center of the stand.
step 6 � �� �� �� �� Figure 6 Parts: • Stand base assembly from Step 5 • Right Dumbbell Platform (#6) Hardware • 2.75" Screws (#13) • Washers (#11) • Nuts (#10) Qty 2 4 2 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 6-1 Secure the Right Dumbbell Platform (#6) to right Stand Leg (#4) using the hardware shown in Figure 6. Note: Make sure the screw holes in the Platform are toward the center of the stand.
step 7 � �� �� �� �� �� �� Figure 7 Parts: • Stand assembly from Step 6 • Towel Bar (#7) Hardware • 1" Screws (#15) • Washers (#11) • Nuts (#10) Qty 4 4 4 Tools: • Hex Key (7/32”) • Wrench/Socket (9/16”) or Adjustable Wrench 7-1 Attach the Towel Bar (#7) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) using hardware shown in Figure 7. Hand tighten screws in a cross pattern, to ensure even fit. 7-2 Tighten all screws securely.
step 8 � �� � Figure 8 Parts: • Stand assembly from Step 7 • Foot Pegs (#8) or Caster Wheels (#16) • Hold Down Straps (#9) 8-1 Attach either Foot Pegs (#8) or Caster Wheels (#15) to the Rear Left Stabilizer (#2), the Rear Right Stabilizer (#3), and both Stand Legs (#4). See Figure 8. 8-2 Attach the Hold Down Straps (#9) to the Left Dumbbell Platform (#5) and the Right Dumbbell Platform (#6) as shown in Figure 8.
16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS www.nautilus.com © 2006 Nautilus, Inc. All Rights Reserved. Bowflex and Bowflex SelectTech are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change.
