® Bowflex Xtreme® 2 SE Home Gym Assembly Manual ®
Congratulations on your commitment to fitness and your purchase of the Bowflex Xtreme® 2 SE home gym. Before assembling your Bowflex Xtreme® 2 SE home gym please read the Assembly Manual and follow the Important Safety Precautions. For information on how to use your Bowflex Xtreme® 2 SE home gym, refer to the Bowflex Xtreme® 2 SE Owner’s Manual. Table of Contents Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before Assembly . . . . . . .
Important Safety Instructions Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Before using this equipment, obey the following warnings: Read and understand all warnings on this machine. Carefully read and understand the Assembly Manual. • Keep bystanders and children away from the product you are assembling at all times. • Do not assemble this machine outdoors or in a wet or moist location.
Parts Important: Leave all Cables coiled and wrapped until your Bowflex Xtreme® 2 SE Home Gym is fully assembled. 10 8 C J O B 9 B C G 14 2 N Q 19 B 20 22 O 11 12 21 N D 21 M 15 E I B 13 K 14 B I 3 8 K E 18 A F O B P B 17 H B O 8 5 E L 16 D R 4 B 6 27 ? 26 25 Q B 23 B O 1 7 24 25 26 27 Note: Cables are not shown for clarity.
Parts Item Qty Description Item Qty Description 1 1 Base Frame Assembly 16 1 Lock Knob 2 1 Bfx Rod Pack 210# 17 1 Seat Backbone Assembly 3 1 Lower Lat Tower 18 1 Seat Bottom 4 1 Seat Support Rail 19 1 Ab Crunch Crossbar 5 1 Squat Frame Left 20 1 Ab Crunch Bracket 6 1 Squat Frame Right 21 2 Pulley, Pair Floating 7 1 Squat Platform 22 1 Lat Double Pulley / Housing 8 4 Pulley Slider, 4” w/o Decal 23 1 Leg Extension Backbone 9 1 Rear Lat Crossmember 24 1
Hardware (NOTE: Drawings not to scale.
Assembly Guide Step 1 Install Power Rod® Pack to Lower Lat Tower Assembly Parts: • L ower Lat Tower (3) • Rod Box with Power Rod® Pack (2) Hardware: 2 3 • 3 Phillips Screws #10 X 1” (F) • 3 Flat Washers 1/4”(A) Tool: Phillips Screw Driver 1-1 Lay parts on floor as shown. Firmly slide Rod Box into Lower Lat Tower frame. 1-2 Fasten the Rod Box to the Lower Lat Tower frame as shown. Tighten screws until snug.
Assembly Guide Step 3 Install Seat Support Rail Parts: • S eat Support Rail (4) • Base Frame Assembly Hardware: • 2 Button Head Screws 3/8” X 3/4” (I) • 2 Flat Washers 3/8” (B) Tool: 7/32” Hex Wrench 3-1 Slide the bottom of the Seat Support Rail onto the Base Frame connector as shown. 3-2 Slide the top of the Seat Support Rail onto the Lower Lat Tower Assembly connector as shown. Secure using screws and washers as shown. Finger tighten screws at this time.
Assembly Guide Step 4 Install Squat Pulley Frame Parts: • Left Squat Pulley Frame (5) • R ight Squat Pulley Frame (6) • Main Assembly • 2 Slider Pulleys w/o Decal (8) • Squat Platform (7) 8 5 O B Hardware: • • • • • 1 Button Head Screw 3/8" X 5" (H) 5 Nylock Nut 3/8" (O) 2 Button Head Screws 3/8" X 3/4" (I) 12 Washers 3/8" (B) 4 Button Head Screws 3/8” X 2 3/4” (Q) I B B 6 Tools: 7/32" Hex Wrench, Adjustable B O or Socket Wrench Q B 4-1 Place one Squat Pulley Frame on
Assembly Guide Step 5 Install Pulley Arms Parts: • R ight Pulley Arm (12) • Left Pulley Arm (13) • Main Assembly 12 N D M 13 Hardware: • 2 Threaded Studs 1/2" X 9 1/2" (M) • 4 Nylock Nuts 1/2" (N) • 4 Washers 1/2" (D) D Tools: 7/32" Hex Wrench, Rubber Mallet 5-1 Align the two holes in the Pulley Arms with those in the Lower Lat Tower Assembly and secure using threaded studs, 1/2” washers and nuts as shown.
Assembly Guide Step 7 Seat Assembly L Parts: • S eat Backbone (17) • Seat Bottom (18) E Hardware: • 4 Button Head Screws 5/16" X 3/4" (L) • 4 Washers 5/16" (E) 17 18 Tool: 3/16" Hex Wrench 7-1 Install the Seat Backbone to the underside of the Seat Pad using screws and washers as shown.
Assembly Guide Step 9 Install Leg Extension Assembly 16 Parts: • L eg Extension Assembly • Lock Knob (16) • Seat Assembly 9-1 Insert Leg Extension Backbone into open end of Seat Backbone as shown. 9-2 Align one hole of the Leg Extension with the hole in the Seat Backbone to fit your height and secure with the Lock Knob as shown.
Assembly Guide Step 11 Install Seat Assembly Parts: • S eat Assembly • Seat Locking Pin (P) • Main Assembly 11-1 Align the top two hooks on the Seat Backbone (17) with one of the pairs of pins on the Seat Support Rail (4), as shown in Detail 11a. 11-2 Tip seat front up and slide hooks onto pins. Rotate seat down and back to use. P 11-3 Slide the Seat Locking Pin through the holes in the Seat Backbone hooks to secure the seat assembly on the Seat Support Rail as shown in Figure 11b.
Assembly Guide Step 12 Upper Lat Tower Assembly 8 Parts: • U pper Lat Tower (11) • Lat Cross Bar (10) • Rear Lat Crossmember (9) Hardware: • • • • • • J 9 C O 10 B 2 Button Head Screws 3/8" X 3" (G) 4 Washers 3/8" (B) 2 Nylock Nuts 3/8” (O) 2 Button Head Screws 1/2" X 5 1/4" (J) 4 Wide Washers 1/2" (C) 2 Nylock Nuts 1/2” (N) B G C 8 Tool: 7/32" Hex Wrench and Adjustable Wrench 11 12-1 Align the two holes on the Lat Cross Bar with those on the Upper Lat Tower as shown.
Assembly Guide Step 14 I nstall Upper Lat Tower Assembly, Ab Crunch Station and Lat Pulley Parts: • • • • pper Lat Tower Assembly U Ab Crunch Station Lat Pulley Housing (22) Main Assembly Figure 14a Hardware: • 5 Button Head Screws 3/8" X 3/4" (I) • 5 Flat Washers 3/8" (B) Tool: 7/32" Hex Wrench 22 14-1 Slide the Upper Lat Tower Assembly onto the Lower Lat Tower as shown. 14-2 Place the Ab Crunch Bracket against back of the Lat Tower Assembly.
Assembly Guide Step 15 Cable and Pulley Routing – Overview The figure below shows all Pulleys on the Bowflex Xtreme 2 SE home gym. Subsequent images show how to connect and route each of the Cables through the Pulleys. (The Ab Crunch Station is not shown for clarity.) Connecting the Cables is much easier with a second persn assisting you. Note: A ll references to the right or left of the machine are from the viewpoint of standing in front of the machine facing the seat.
Assembly Guide 2 2 1 1 Step 16 Cable and Pulley Routing – Prepare Cables to be installed to the Lat Pulley Housing Locate the following items on the Lat Pulley Housing assembly: • ( 2) Pulleys – already installed, labeled as item 2 in figure • 3 /8” X 4 1/2” Hex Head Bolt – installed • 3 /8” Washer – already installed Note: Connecting the Cables is much easier with a second person assisting you.
Assembly Guide 2 2 1 1 Step 17 C able and Pulley Routing – Connect Pulleys and Cables to the Lat Pulley Housing Locate the following items for the Lat Pulley Housing assembly: • ( 2) Pulleys from step 16 • 3 /8” X 4 1/2” Hex Head Bolt – uninstalled in Step 16 • 3 /8” Washer – uninstalled in Step 16 Note: Connecting the Cables is much easier with a second persn assisting you. 17-1 Holding both Cables from Step 16 in place, align the 2 Lat Pulleys as shown in Figure 17.
Assembly Guide Step 18 Cable and Pulley Routing – Connect Rod Cables through the Right Floating and Lat Tower Pulleys Locate the following items for the Lat Pulley Housing assembly: • 3 & 8 Floating Pulleys (connected unit) • ( 2) Cable End Stop Balls with Core (see Detail) 18-1 Locate the Right Rod Cable that you ran through the Lat Pulley Housing. Thread the Cable through the (3) Floating Pulley, as shown.
Assembly Guide Step 18b Cable and Pulley Routing – Connect Cable End Stop Ball with Core Figure 18b - Detail Step 18c Cable and Pulley Routing – Connect Rod Cables through Left (3) Floating and Lat Tower Pulleys Figure 18c 18-4 Repeat with Left Rod Cable and (3) and (8) Floating Pulleys, as shown in Figure 18c. 5 4 Note: Once the Cable End Stop Balls are attached, hook each Rod Hook onto the Lat Pulley Housing as shown in Figure 18d.
Assembly Guide 10 8 6 9 7 Step 19 Cable and Pulley Routing – Connect Right Squat Cable through the Floating and Main Assembly Pulleys Slide the Right Squat Frame Pulley (6) to the furthest back hole, as indicated in Figure 19. Unwrap the Right Squat Cable from the (6) Pulley and guide the Cable, threading under and through the Rear Cross Bar Pulley (7), and up through the Floating (8) Pulley. Follow the arrows as indicated in Figure 19.
Assembly Guide 10 8 6 9 7 Step 19b Cable and Pulley Routing – Connect Left Squat Cable through the Floating and Main Assembly Pulleys Repeat the same procedure completed during Step 19 for the Left Squat Cable.
Assembly Guide 6 6 Step 20 Cable & Pulley Routing Attach the hooks on the ends of the Left and Right Squat Cables to the Hook installed onto the Leg Extension, as shown in Figure 20. Step 21 Final Inspection Inspect your machine to ensure that all fasteners are tight and components are properly assembled. Review all warnings affixed to machine. Be sure to record the serial number in the field provided at the front of the Owner’s Manual.
Nautilus® Bowflex® Schwinn® Fitness 8001515.010913.
