Accessory Rack Assembly Instructions P/N 001-6930 RevB (07/2006)
Table of Contents Product Specifications ......................................................2 Safety Requirements ..........................................................3 Complete Rack Component Diagram ..............................4 Parts List ...............................................................................4 Assembly Steps...................................................................5 Storing Your Accessories ..................................................
�� � � � � � � � Safety Requirements IMPORTANT SAFETY INSTRUCTIONS ������������������������� The following definition applies to the word “Caution” found throughout this manual: ������� Used to call attention to POTENTIAL hazards that could result in personal injury or damage to equipment. READ ALL INSTRUCTIONS BEFORE USING THE EQUIPMENT. • Always read and follow the Safety labels attached to your Bowflex Ultimate® 2 Accessory Rack . Do not remove these labels.
Complete Rack Component Diagram � � �� � �� �� � � � � � � �� �� � �� � Hardware Parts # 4 Qty.
step 1 Parts: • Side Tubes (#9) • Bottom Bracket (#10) Hardware • 2 3/4" Bolts (#13) • Washers (#15) • Nuts (#14) � Qty 4 8 4 �� Tools: • Allen wrench (7/32”) • Wrench/Socket (9/16”) or Open End Wrench 1-1 �� Attach the Bottom Bracket (#10) to the Side Tubes (#9) using the hardware shown in Figure 1. Note: Do not tighten hardware at this time.
step 3 Parts: • Base Plate (#11) • Curl Mount (#6) Hardware • 7/8" Bolts (#12) • Washers (#15) � Qty 2 2 Tools: • Allen wrench (7/32”) 3-1 �� �� Attach the Preacher Curl Mount (#6) to the Base Plate (#11) using the hardware as shown in Figure 3. The Curl Mount should lean toward the U-shaped bars on the Base Plate. �� Figure 3 Tighten hardware completely.
Parts: • Rack base assembly from Step 4 • Right Curl Bar Hook (#2) • Left Curl Bar Hook (#3) • Bar Hook Brackets (#4) • Washer Hooks (#7) Hardware Qty • 2 3/4" Bolts (#13) • Washers (#15) • Nuts (#14) �� step 5 �� �� �� �� �� � � � � � 8 14 8 Tools: • Allen wrench (7/32”) • Wrench/Socket (9/16”) or Open End Wrench � � � � Figure 5 (Left Tube – Front View) 5-1 Install the Left Curl Bar Hook (#3) at the two top, outside bolt holes on the left Side Tube (#9) using the hardware shown in Figu
step 7 � � � � � � � Figure 7 �� � � � � � Parts: • Rack assembly from Step 6 • Flex Bag (#8) • Color-coded Dots (6 pairs) ������ 7-1 Fasten the Flex Bag (#8) to the Side Tube uprights below the Curl Bars, using the hook-and-loop straps. See Figure 7. 7-2 The pairs of colored dots will identify the storage locations for the Bowflex Ultimate® 2 accessory equipment listed in the guide chart below.
Your Bowflex Ultimate® 2 Accessory Rack is now complete. You are ready to store your equipment.
WARRANTY LIMITED WARRANTY FOR EXERCISE PRODUCTS All Bowflex® branded exercise products manufactured by Nautilus, Inc. are warranted to the retail purchaser to be free from defects in materials and workmanship. Warranty coverage valid to the original purchaser only and proof of purchase will be required. Any product sold or placed in an application not recommended by Nautilus will void any warranty coverage set forth by Bowflex® warranty policies and procedures.
IMPORTANT CONTACT NUMBERS If you need assistance, please have both the serial number of your rack and the date of purchase available when you contact the appropriate Nautilus, Inc. office listed below. WORLDWIDE CUSTOMER SERVICE • NORTH AMERICA OFFICE Nautilus, Inc. World Headquarters 16400 S.E. Nautilus Drive Vancouver, Washington, USA 98683 Phone: 800-NAUTILUS (628-8458) Fax: 877-686-6466 e-mail: cstech@nautilus.com INTERNATIONAL CUSTOMER SERVICE • SWITZERLAND OFFICE Nautilus International S.A.
16400 SE Nautilus Dr. Vancouver, Washington, USA 98683 1-800-NAUTILUS (800-628-8458) www.nautilus.com © 2006 Nautilus, Inc. All Rights Reserved. Bowflex, the Bowflex logo and Bowflex Ultimate are either registered trademarks or trademarks of Nautilus, Inc. Specifications subject to change.
