Instruction Manual

BN20914
SAVE?
P/W CHANNEL MEASURE SPEC MASTER CLASS RS232C ETC.
> 2 sec
(xxxx)
SOURCE EXT. M1 SELECT ON M1 NOMI.
ⓔ
M1 - MASTER
ⓓ
SELECT OFF SPEED 4800 GENERAL UNIT METRIC
CH-BUS OFF ON 9600 INCH
- TOLER
ⓕ
+ MASTER
ⓓ
19200
PRESET VALUE
CH-A RATIO= 0 ~ 5.000 BAR BOTTOM CLASS_No 4~100 DISPLAY
㎜
>0.5 sec
"
CENTER + TOLER
ⓕ
M2 - MASTER
ⓓ
DATA 7
㎛
M1
ⓐ
DIREC.= +
-10 → 0
START
ⓖ
8
- -APPRO
ⓕ
+ MASTER
ⓓ
INPUT
HBT
M2
ⓐ
"
B.FACT 0.1 ~ 5.00 STEP
ⓗ
PARITY NONE
LVDT
CH-D RATIO= 0 ~ 5.000 +APPRO
ⓕ
M3 - MASTER
ⓓ
ODD
CAP_1
M3
ⓐ
RANGE
ⓑ
EVEN
CAP_5
DIREC.= + M2 NOMI.
ⓔ
+ MASTER
ⓓ AIR
M4
ⓐ
- SENS.
±0.010~5.000
TERM
CRLF
- TOLER
ⓕ
M4 - MASTER
ⓓ CRLF
P/W PROGRAM ****
OR
RESOL
ⓒ
+ TOLER
ⓕ
+ MASTER
ⓓ
RTS
ON
CAL.P/W OFF
P/W CAL..M(X) MOUDLE CAL%
CH-EA RATIO= 0 ~ 5.000 FUNC
A OFF
ON ****
>0.5 sec
(xxxx)
"
B -APPRO
ⓕ
AVERAGE BAR 2~50
CAL＿
M1 NONE DIREC.= + C PRINT
BRIEF
- D +APPRO
ⓕ FULL
DIGIT 2~50
CAL￣
M2 VALUE 000%
"
A+B
CH-ED RATIO= 0 ~ 5.000 A–B M3 NOMI.
ⓔ
RSMODE
PRINT
A/D 2~20
xxxx M3 C+D
HOST
DIREC.= + (A+B)-C - TOLER
ⓕ
VERSION V 2.xx
xxxx M4 - (A+B+C)/3 ID_NO
0~255
(A+B+C+D)/4 + TOLER
ⓕ
(A+B)-(C+D)
+ ADJUST
-APPRO
ⓕ
>0.5 sec MODE STATIC
CH-A xxxx MAXIMUM +APPRO
ⓕ
" MINIMUM
" (M+m)/2 M4 NOMI.
ⓔ
CH-D xxxx (M-m)/2
M-m - TOLER
ⓕ
CH-EA xxxx
" M2 Same as M1 map + TOLER
ⓕ
Enter Key
"
CH-ED xxxx M3 Same as M1 map -APPRO
ⓕ
Left/Right Key
M4 Same as M1 map +APPRO
ⓕ
Up/Down Key
+ Power S/W
Menu Map for PC2200(V2.xx)
M1~M2~M3~M4 Transfer (Toggle key)
Data sending(Digital display Value)
NO(ESC)YES(ENTER)
Initialization of setup data
Reset in dynamic mode
Retun to upper menu in setup mode
Prog
Preset
Cal
Enter
Esc
S
M