Data Sheet

Thomann GmbH
Hans-Thomann-Straße 1 • 96138 Burgebrach
Germany • www.thomann.de
DocID: 477410_20.02.2020
EN
PSA 16PT2-TR1 Power Distributor 16A
Features
 19" rackable power distributor, 1RU
 LED indicator for voltage present per phase
 Housing material: Metal
 Outputs rear panel: 6×Power Twist TR1
(each 2 per phase)
 Input: CEE 16A plug with cable
(H07RN-F 5G2.5mm²)
 Cable length: 1.7m
Technical specications
 Supply voltage: 400V~50Hz
 Load capacity: 16A per phase
 Fuses 3×C16 circuit breaker
 Protection: IP20
 Dimensions W×H×D: 482×44×120mm
 Weight: 3.5kg
Safety instructions
Intended use
This device is meant to be used for the distribution of manins power to
multiple loads. Any other use or use under other operating conditions
is considered to be improper and may result in personal injury or prop-
erty damage. No liability will be assumed for damages resulting from improper
use.
Dangers for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not
within reach of babies and young children. Choking hazard! Ensure that children
do not detach any small parts (e.g. knobs or the like) from the unit. They could
swallow the pieces and choke! Never let children unattended use electrical de-
vices.
Operating conditions
This device has been designed for indoor use only. To prevent damage, never
expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt,
and strong vibrations.
Risk of re if the maximum current is exceeded
The device can power other devices via a lockable Power Twist output socket.
The current consumption of all serially connected other devices must not ex-
ceed 16 A, otherwise you risk injuries and irreparable damages of the device.
Connect just so many devices to the output socket that the maximum current
consumption is not exceeded.
Ensure the correct dimensioning (wire cross section) of the used power cords of
all serially connected devices.
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never
remove any covers. There are no user-serviceable parts inside.
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a
protective contact plug. Do not modify the mains cable or the plug. Failure to
do so could result in electric shock/death or re. If in doubt, seek advice from a
registered electrician.
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches
the voltage rating of the device and that the AC outlet is protected by a residual
current circuit breaker. Failure to do so could result in damage to the device and
possibly injure the user.
Unplug the device before electrical storms occur and when it is unused for long
periods of time to reduce the risk of electric shock or re.
Handling the power cord
Do not place the device or speaker boxes or similar on the power cord and be
careful not to pinch it. Never tie a knot in the power cord or tie it with other
cables. Route the power cord so that no one steps on or trips over it. A damaged
power cord can cause a re or electric shock. Replace any broken cables.
Protecting the environment
For the transport and protective packaging, environmentally friendly
materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of. Do not
just dispose of these materials with your normal household waste, but make
sure that they are collected for recycling. Please follow the notes and markings
on the packaging.
This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version. Do not dispose
of your old device with your normal household waste. Dispose of this
product through an approved waste disposal rm or through your local
waste facility. Comply with the rules and regulations that apply in your country.
If in doubt, consult your local waste disposal facility.