BOSSCOM Powerlink - Switch Stereo Audio Switch | Two Jacks | Automatic Switching | B&O® Compatible Installation Guide
Contents Page 3..........BOSSCOM DENMARK 4..........Examples of Use I. Converting LF-Signals (stereo RCA) to standard-conforming B&O® Powerlink signals 5..........Examples of Use Feed-in of LF-Signals (stereo RCA) to B&O® Systems with II. automatic switching 6..........Examples of Use Dolby Surround setup for LOEWE ® TV and B&O® Systems with automatic switching (with trigger signal) III. 8..........Safety Instructions 9.........Connections · Front 10.........Connections · Rear · Left 11........
. BOSSCOM BOSSCOM The digital world of consumer electronics offers high-quality devices, technologically sophisticated devices, devices with great design and easy-to-use devices. And there are a few devices that combine all these in one, to cater to all needs of the customer - like BOSSCOM devices of ip media systems GmbH. This requires exploring new and unconventional ways and being able to rely on years of experience.
. Examples of Use I. Converting LF-Signals (Stereo RCA) to Standard-Conforming ® B&O Powerlink Signals ® ® B&O Speakers ® e.g. BeoLab 8000 B&O Speakers ® e.g. BeoLab 8000 any stereo source such as BOSSCOM Powerlink-Switch ® SONOS Zoneplayer Connect any stereo source with an RCA cable to INPUT 1 of the BOSSCOM Powerlink-Switch, via the adapter cable (included) and use the device as a Powerlink converter.
. Examples of Use II. Feed-in of LF-Signals (Stereo RCA) to B&O® Systems with Automatic Switching (without trigger signal) ® ® B&O Speakers ® e.g. BeoLab 6000 BOSSCOM Powerlink-Switch B&O Speakers ® e.g. BeoLab 6000 Any stereo source, e.g. SONOS® Zoneplayer B&O® System e.g. BeoSound 9000® Interconnect the BOSSCOM Powerlink-Switch between your B&O® system and your B&O® speakers. Connect any stereo source with an RCA cable to INPUT 1 of the BOSSCOM Powerlink-Switch, via the adapter cable (included).
. Examples of Use III. Dolby Surround Setup for LOEWE® TV and B&O® Systems with Automatic Switching (with trigger signal) Front Speakers ® e.g. BeoLab 8000 Front Speakers ® e.g. BeoLab 8000 TV with Dolby Surround decoder, like ® LOEWE ® Individual ® B&O System e.g. ® BeoSound 3200 2 x BOSSCOM Powerlink-Switch Rear Speakers ® e.g. BeoLab 3 Rear Speakers ® e.g. BeoLab 3 Use two BOSSCOM Powerlink switches and connect for example your LOEWE ® TV to your B&O® system and your B&O® speakers.
. Examples of Use III. Your stereo source - in this example, a BeoSound 3200® - is going to be connected to INPUT 2 of both BOSSCOM Powerlink switches. You will need a Powerlink Y-cable. You can also create a trigger level, by connecting the adapter cable (included) to each INPUT 1 of the BOSSCOM Powerlink switch, if the audio source provides such, like the LOEWE® TV in the example shown.
. Safety Instructions Connect the device to the mains supply, via the supplied power cord. Do not repair damaged cables. The operating voltage must match the local mains voltage. Protect the device from humidity and moisture. Do not operate the device in the rain. The device may not be used near water, bathtubs, washbasins, kitchen sinks, wet rooms, swimming pools or damp rooms. Do not place objects filled with liquids such as vases, jars, bottles, etc. on the device.
. Connections Front 2 3 1 1 INPUT 1 8-pin DIN jack Pin Pin Pin Pin 1 - Trigger ON/OFF 2 - Ground 3 - Input right 4 - Input for trigger signal (5-15 V DC) to enable INPUT 1 Pin 5 - Input left 2 INPUT 2 (Powerlink Input) 8-pin DIN jack Pin Pin Pin Pin 3 2 3 4 5 - Ground Input right Powerlink mute circuit voltage (5 V DC) Input left OUTPUT (Powerlink Output) 8-pin DIN jack Pin Pin Pin Pin 2 3 4 5 - Ground Output right Powerlink mute circuit voltage (5 V DC) Output left
. Connections Rear 4 4 Mains Connection Connect the Euro-mains socket to the socket, with the included power cable.
. Connections Right side 6 7 Level Increase 6 right channel 7 left channel Signal amplification for devices with a reduced line-level, such as MP3 players like the Apple® iPod®, that are connected to INPUT 1, for adjusting the volume to the source INPUT 2. The right and left channel can be independently controlled. Counter-clockwise (left) turning raises the level up to 6 dB delivery condition is 0 dB (set fully clockwise).
. Block Diagram Schaltlogik = Switching Logic NF-Erkennung (Ausschaltverzogerung – 1 Min) = LFRecognition (switching off delay – 1 min.
. Technical Data Powerlink Signals INPUT 2 and OUTPUT are 100% B&O® compatible Remote Power INPUT 1 ON/OFF via external contact voltage (5-15 V DC) to 8-pin DIN input jack "ON" as soon as a low-frequency signal is present "OFF" (Standby), when no low-frequency signal is received for at least 1 minute Automatic Activation INPUT 1 Level Increase INPUT 1] Max.
