AUDIO SYSTEMS k'a
-S M A N U channel Amplifier Power / Speaker Wiring Bridged Speaker Wiring Tri-mode Speaker Wiring Precautions B d a d * c "+
--. 1. . - MODEL -. RMS M t t s / C H at 4 dhms RMS Watts/CH at 2 Ohms RMS Watts/CH at 1 ohmsMAX Watts/(H at 0.
I-db-4 v k/ Congratulations on your purchase o ~ a 9 " & b d ( o ~ y & r i w ' mDRIVE ~ cC&io amplifier. POWER DRIVE amplifiers are designed, and engineered in the USA to the highest level of quality, and will afford you years of listening enjoyment. Ld -r 1 All POWER DRIVE amplifiers utilize fully-regulated MOSFET power supplies, whicn assure that switching response is extremely fast and output power is clean. / I Thank you for making 33S@Audio Systems your choice for car audio equipmer , - ~.
Electrical Wiring All 3 3 ~ POWER 9 DRIVE amplifiers are equipped with easy access screw terminals. These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following: . Use at least 4 gauge or heavier wires for power and ground connections. Connect the BATTERY-(+)terminal to the positive (+) terminal of the car battery.
Electrical Wiring All 3 3 s ' POWER DRIVE amplifiers are equipped with easy access screw terminals. These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following: . Use at least 4 gauge or heavier wires for power and ground connections. Connect the BAlTERY.(+) terminal to the positive (+) terminal of the car battery.
WARNINGS 1.HIGH CURRENT Amplifier (including this model) cab d S b e c o m e q u i t e hot, w h e n u s e d in poorly v e n t i l a t e d 1 areas or with i m p e d a n c e s l o w e r than that whl'&' is recommended. Please avoid s i t u a t i o n s w h i c h MAY contribute 4 .! : -/r 1 it^^ excessive heat build-up, resulting in possible damage to o t h e r areas of your automobile. 2. Please note that it is necessary to completely remove the end-caps before power connections can be made.
Tko Channel Ampl5fOer PowerISpeaker Wring ~ , - , d P D - 1 0 0 0 5 -?-L% - .-, Bridged Speaker Whhg , -,~. PD-2000, and PD-I - . 1J I d SPEAKER IMPEDAN 1-8 OHMS! I I - IFIER TERM= 'li 8 ttc, J .
Tri-mode Speaker Wiring PD.4000, PD-3000, PD-2000, and PD-1000 Tri-Mode Operational Output is a unique feature which allows two channels of an amplifier to drive a subwoofer operated in MONO mode, while simultaneously driving full range speakers in STEREO. To engage the amplifier in this mode, place the Crossover (Subwoofer) switch in the "FULL" position.
Precautions Before you drill or cut any holes, investigate your car's layout very carefully. Take care when you work near the gas tank, fuel lines, hydraulic lines and electrical wiring. Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident. Do not mount this amplifier so that the wire connections are unprotected or in a pinched condition, or likely to be damaged by nearby objects.
Troubleshooting If your amplifier is not operating properly, refer to the list below and follow the suggested procedures. Always test the speakers and check the wiring first. Confirm that all terminal strip connections are secure and tight. No output Check both in-line and built-in fuses. Both the "+I 2v" and the "REMOTE" terminals must have +12v referenced to chassis ground. Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal.
